Escolar Documentos
Profissional Documentos
Cultura Documentos
CHAPTER 2
LTE MOBILITY
The mobility procedures can be classified into two modes namely idle mode and
connected mode. The network controls transition of UE between the idle and RRC
(Radio resource control) mode according to its activity and mobility.
Idle mode UE, as the name suggests that UE is not actively communicate with the
network and have not been assigned the network resources. For example, when the UE
is turn on for the first time, it starts the initial cell selection procedure. It receives the
broadcast channels in the E-UTRAN cell of a Public Land Mobile Network
(PLMN).The UE start to check the network information received from the broadcast
channels and select a suitable cell with good radio quality. The main purpose of this
procedure is to ensure that the UE could connect to the network resources as soon as
possible. This procedure is known as Initial Cell Selection. Here it should be mentioned
that the UE may have some stored information about the available or carrier frequencies
and cells in the neighborhood. This information may get from the system or has been
acquired in the past by UE.
After this initial cell selection, the UE have to register itself to PLMN of the selected
cell. During a while, the UE will continue to find a better cell as compared to the present
one for reselection of cell.
16
Here the UE will use the cell reselection criterion. We may differentiate the cell
reselection into two types namely as Intra-frequency cell reselection and Inter-
frequency / RAT (Remote Access Technology) cell reselection.
Intra-frequency cell reselection is following the cell ranking criterion. The network
defines some neighbor cells to the UE in order to measure its radio quality for
reselection procedure. Cell ranking is used by UE to find a good radio quality cell for
camping. This ranking is based on the Rs criterion for the serving cell and Rn for the
neighboring cells. i.e
Rs = Qmeas,s + Qhyst
Rn = Qmeas,n + Qoffset
Whereas Qmeas is the Reference Signal Received Power (RSRP) measurement quantity,
Qhyst denotes the power domain hysteresis to avoid the UE ping-pong and Q offset is an
offset value to control different frequency or cell specific characteristics. Hence the UE
can reselect the best ranked neighbor cell if it has good radio quality then the serving
cell for a longer time than Treselction(gives the cell reselection timer value).
Similarly, the network may also not allow the UE to reselect some cell known as
blacklisted cells. Some limits have been defined [1] in order to minimize the number of
measurements. So if ‘SServingCell’ (Specify a threshold for intra frequency in dB) is high
enough, then UE are not allowed to do any intra-frequency, inter-frequency or inter-
system measurements. The range for intra-frequency measurements is that if
SServingCell ≤ SintraSearch.
17
In E-UTRAN LTE, Absolute priority based reselection method is introduced for the
inter-frequency/ RAT reselection. Here the UE will prioritize the different frequencies
or RATs in the form of layers. Each layer is being given priority and UE use those
criteria for reselection procedure. Hence if a UE wants to reselect another layer with
good services, so it will have check the threshold level denoted by Threshx, high.
Similarly, for the inter-frequency measurements, the following relation must come true
which is SServingCell ≤ SnonintraSearch.
Tracking Area is the area/cell tracked by an eNodeB. During the cell selection/
reselection procedure, there is a chance that UE may change its tracking area. This
tracking area is being controlled by the MME. The larger the tracking area, the lesser
the signaling load and vice versa. Similarly, the smaller tracking area has minimum
paging signaling. This tracking area in UTRAN is known as a Routing area.
Moreover, when the UE found a cell of good quality as compared to the current one, the
eNodeB allows the UE to handover to that cell. This LTE handovering from the eNodeB
to other cells, may from same LTE carrier (Intra-frequency handover), to LTE cells on
other carriers (Inter-frequency handover) as well as cells of different RAT.
E-UTRAN has the authority to make handovering of the UE. Hence the network
has to decide the time and cell for UE handovering.
E-UTRAN assigns the parameters to UE for measurement and UE send a
measurements report to network. After then the network decides the handover
according to the UE measurements.
After completing the handovering, the S1 connection between the target eNodeB
and the core network is also updated. This process is known as Late path switch.
While the core network have no control on the handovering of UE.
When the target eNodeB find the availability of resources, the source eNodeB will
command the UE to handover to target cell. The UE have the capability to make direct
connection with target eNodeB. As this whole procedure has been done on the
E-UTRAN level so the core network have no information regarding handovering.
Finally, the target eNodeB updated S1 connection with core network and the process is
named as late path switching.
The X2 based handover scenario will be explain in handover procedure section. The X 2
is the interface between the two eNodeB’s to communicate with each other. The X2-AP
is the protocol used for the communication over this interface. The X 2 based
handovering is performed between the two eNodeBs which are directly connected to
each other via X2 interface. Here the source eNodeB and target eNodeB is served by the
same MME and SGW.
The S1 interface provide the connectivity between the eNodeB and Evolved packet core
(EPC) which is further divided into two interfaces. One interface is used by the control
plane while other one is for user plane.S 1 based handover scenario take place when the
source and target eNodeB’s are served by different MME’s. It means that there will be
no direct X2 connectivity between the two eNodeB’s.
20
Here the source eNodeB will be serving by the source MME and source SGW and the
target eNodeB will be served by the target MME and target SGW. While the source and
target MME’s can communicate over S 10 interface. Hence all the handovers decision
will take place on the S1 interface, so it’s known as S1 based handover.
Here we will define the signaling messages which have been transferred between the
UE, E-UTRAN and core network elements (MME & GW). We can divide the procedure
into three parts namely as Handover preparation, Handover execution and Handover
completion.
Here the target eNodeB informs the MME about handovering of the UE by sending the
PATH SWITCH message. In the same way, the MME inform the Serving Gateway
(SGW) about the new location of UE via USER PLANE UPDATE REQUEST message.
Hence the SGW switches the downlink path to the target eNodeB and also inform the
MME via USER PLANE UPDATE RESPONSE message. Similarly, the MME
confirms the PATH SWITCH message with the PATH SWITCH ACK message.
Finally, the target eNodeB request the source eNodeB to release the UE related
resources by sending RELEASE RESOURCE message.
22
Inter-LTE handover have almost the same procedure as compared to the intra-LTE
handovering. But the main difference is that, upon inter-LTE handover the whole AS-
configuration have to be signaled while in Intra-LTE, there is no need of wide range of
signaling [2].
The procedure for Inter-LTE handover can be illustrated in figure 2-8. In the Inter-LTE
handover, the UE can send a MEASUREMENT REPORT message to source eNodeB
for handovering. Similarly, the source eNodeB may also request the target RAN (Radio
Access Network) for handovering by sending the HANDOVER PREPARATION
REQUEST. In this message, the source eNodeB also provides the information to target
RAN about the UE capabilities. Hence, the target RAN responds with HANDOVER
COMMAND to the source eNodeB.
During this while, the source eNodeB instruct the UE for handovering via MOBILITY
FROM EUTRA COMMAND message. On receiving this message, the UE start to make
connection with the target node.
23