Escolar Documentos
Profissional Documentos
Cultura Documentos
Refer to the exhibit. Which route will appear in the routing table?
3
What will be the two wildcard masks required in an extended access list statement that
blocks traffic to host 192.168.5.45 from the 172.16.240.0/27 network? (Choose two.)
0.0.0.0
255.255.240.0
255.255.255.255
0.0.31.255
255.255.255.240
0.0.0.31
4
Which bandwidth allocation technique minimizes bandwidth waste by reallocating unused
time slices to communicating users?
VPN
NCP
TDM
STP
STDM
5
Which two statements are true about RIPv1 and RIPv2? (Choose two.)
Both versions support the features of split horizon and poison reverse.
Refer to the exhibit. A network administrator must manually summarize all IP addresses on
the POP router for the ISP. Which one is the correct summary address?
192.168.0.0/22
192.168.0.0/23
192.168.0.0/24
192.168.0.0/25
7
After comparing a previous baseline to current network statistics, the network engineer has
discovered a significant increase in unwarranted traffic to the extranet. Which two steps
simplify administration and control the unwanted traffic? (Choose two.)
add an ACL at the router in the enterprise edge to block the traffic
configure all hosts with the same default gateway to eliminate unnecessary broadcasts
deploy one core ISP router to reduce the delay in path determination
8
What do companies gain from the services performed at the enterprise edge?
enhanced performance and reliability through VLANs and redundant trunk links
Refer to the exhibit. What two pieces of information can be gathered from the output of this
command? (Choose two.)
All subnets are being advertised because default summarization was disabled.
The output verifies that EIGRP is advertising only the networks in the same AS.
The 172.16.1.0/24 network is directly attached to the router that produced this output.
The Null0 interface indicates that this is not an actual path, but a summary for advertising
purposes.
10
Refer to the exhibit. Assuming that the RIPv1 routing protocol is enabled and that all
networks are being advertised, which statement is true?
None of the packets from H1 that are destined to H2 will arrive at H2.
Approximately half the traffic from H1 that is destined to H2 will reach R3.
Some of the packets from H1 that are destined to H2 will be sent to the switch that is
connected to network 192.168.3.64/26.
11
Which statement is accurate about the CIR in Frame Relay?
It is important to purchase a CIR that matches the highest bandwidth requirements of the
enterprise.
The CIR can be no lower than the port speed of the local loop.
The CIR defines the contracted maximum rate available from the service provider on the
Frame Relay circuit.
12
What are two characteristics of an extended ACL? (Choose two.)
IP is used to specify all TCP/IP protocols including TCP, UDP, ICMP and routing protocols.
Traffic can be filtered on source and destination address, protocol, and specific port
number.
13
Refer to the exhibit. In what sequence (from first to last) does an OSPF router check the
parameters listed when selecting the DR?
C, B, A, D
D, C, B, A
A, B, C, D
A, C, B, D
B, C, A, D
14
Refer to the exhibit. What three facts represent the result of DR and BDR elections in this
OSPF network? (Choose three.)
15
Which two statements describe how the information contained in a BPDU is used by a
switch? (Choose two.)
16
If a modem is being used to connect to an ISP, which WAN connection type is being used?
leased line
cell switched
circuit switched
packet switched
17
Refer to the exhibit. A network administrator enters the command ip route 10.10.4.16
255.255.255.248 s0/0/1 into the router. What will be the result of this configuration?
A static route to 10.10.4.16/29 is placed into the routing table if interface FastEthernet0/1
goes down.
A static route pointing to 10.10.4.16/29 is only placed into the routing table if the route to
10.10.4.0 is removed.
A static route is not placed into the routing table because a RIP route that includes the
destination network already exists.
18
Refer to the exhibit. What is represented by the Null0 route for the 128.107.0.0 network?
19
What are two ways VLAN memberships can be created in an enterprise network? (Choose
two.)
implementing an access list that specifies which devices are placed into specific VLANs.
20
If an authentication protocol is configured for PPP operation, when is the client or user
workstation authenticated?
21
Refer to the exhibit. R1 is connected to the Internet through its serial 0/0/0 interface. Hosts
on the 192.168.100.0/24 LAN on R1 cannot communicate with hosts on the Internet. What
two NAT configuration issues might explain this failure? (Choose two.)
The access list does not include the group of IP addresses that are supported by the inside
network.
23
Refer to the exhibit. Which IP addressing scheme would be correct for the network?
H1-172.18.0.10/16
H2-172.18.0.11/16
H3-172.18.0.12/16
H1-172.18.0.10/16
H2-172.19.0.10/16
H3-172.18.0.11/16
H1-172.18.0.10/16
H2-172.18.0.11/16
H3-172.19.0.11/16
H1-172.18.0.10/16
H2-172.19.0.11/16
H3-172.19.0.11/16
24
Refer to the exhibit. Internet access is crucial for the company network shown. Internet
access is provided by two ISPs. ISP1 is the primary provider and ISP2 is the backup
provider. The network administrator configures BorderR as the border router so that in
normal operations, all Internet traffic goes through ISP1. However, if the link to ISP1 fails,
then BorderR will automatically forward Internet traffic to ISP2. The administrator
configures two default routes:
However, when the administrator issued the show ip route command to verify the
configuration, only the second default route is in the routing table. Why is the first default
route not showing?
This is expected because the link to ISP1 is active. If the link to ISP1 goes down, then the
first default route will be installed into the routing table.
The first default route cannot be installed into the routing table unless the administrator
manually disables the second default route with the no ip route 0.0.0.0 0.0.0.0 172.16.1.1
command.
25
Which command should a network administrator issue to disable default summarization in
an EIGRP network?
Router(config-if)# no ip summary-address
Router(config-router)# no ip summary-address
Router(config-if)# no auto-summary
Router(config-router)# no auto-summary
26
The headquarters of a corporation uses static routes to connect to three branch offices.
What are two advantages of using static routes for the WAN connections? (Choose two.)
Static routes have higher administrative distances than dynamic routing protocols.
The metrics of a static route need adjusting only if the bandwidth of the WAN connection
changes.
They are more stable and less susceptible to network changes in the interior gateway
protocol.
27
What two statements are true regarding EIGRP tables? (Choose two.)
The topology table shows whether a route is in the passive or active state.
The routing table shows the amount of time elapsed since a router adjacency was formed.
The neighbor table shows all adjacent Cisco devices.
28
Refer to the exhibit. A company has recently installed a new switch (S2) into their network.
After several minutes, the network administrator notices that the new VLAN information is
not being propagated to the new switch. Given the show vtp status command output, what
is the possible problem that prevents the information from being received by the new
switch?
29
Refer to the exhibit. An administrator is adding a new router to the network. The IP address
192.168.13.6/30 has been assigned to the connecting serial interface on R2. What IP
address must the administrator assign to the serial interface of the new router?
192.168.13.4/30
192.168.13.5/30
192.168.13.7/30
192.168.13.58/30
192.168.13.61/27
192.168.13.63/27
30
Refer to the exhibit. A network support technician has been asked to set an IP address on
one of the FastEthernet interfaces on a new router. What is causing the interface to reject
the address?
to eliminate the need to block broadcast packets at the edge of the local network
32
Refer to the exhibit. RIPv2 is configured in the network shown. Hosts in the network have
access to all internal networks but do not have Internet access. On which router should the
commands, shown in the exhibit, be added to provide Internet access for all hosts in the
network?
R1
R2
R3
ISP
33
Refer to the exhibit. If R4 is announcing all shown internal networks as a summary address
to the ISP, which summary address will be most specific?
192.168.1.0/22
192.168.4.0/21
192.168.6.0/23
192.168.8.0/21
192.168.4.0/22
34
When MD5 authentication is used for OSPF routing protocol authentication, what two facts
are known about the key? (Choose two.)
35
What are two benefits of implementing VLANs in an enterprise network? (Choose two.)
allows for the propagation of broadcasts from one local network to another
36
Refer to the exhibit. Because of continuing instability of one of the serial links in the OSPF
network, a network administrator configures router ASBR as shown. Which two statements
will be a result of this configuration? (Choose two.)
Traffic intended for destinations across unstable serial links will be forwarded by ASBR
even when the links are down.
Serial links in range 192.168.0.0 255.255.252.0 will be forced into a passive state.
Networks connected to the unstable serial links will be placed in an unreachable state.
37
Refer to the exhibit. OSPF is enabled and the network has completely converged. Which
two routers will be designated as DROTHER routers? (Choose two.)
R1
R2
R3
R4
38
Refer to the exhibit. Users on the 172.30.20.0/24 network are unable to access any of the
servers located on the 192.168.0.0/23 network. Given the network topology and OSPF
configuration, what two problems exist in this network? (Choose two.)
39
Which two statements are true about the native VLAN on a switch? (Choose two.)
Untagged frames that are received on a trunk become members of this VLAN.
40
In which VTP mode can a switch create VLANs, ignore VTP messages, and not pass local
VLAN information to other VTP domain members?
client
server
pruning
transparent
41
Assuming VLSM is not being used, what impact will adding the command ip route
172.16.64.0 255.255.240.0 serial0/0 have on a router that is already operational in a
network?
All packets with a destination address between 172.16.64.1 and 172.16.80.254 will be
forwarded out serial0/0.
All packets with a destination address between 172.16.64.1 and 172.16.255.254 will be
forwarded out serial0/0.
All packets with a destination address between 172.16.64.1 and 172.16.79.254 will be
forwarded out serial0/0.
All packets with a destination address between 172.16.0.1 and 172.16.64.254 will be
forwarded out serial0/0.
42
What is the term for the value 2172416 that is highlighted in the output of the show ip eigrp
topology command?
43
Refer to the exhibit. R1 and R2 are connected via serial interfaces. Both interfaces show
that there is Layer 2 connectivity between them. The administrator verifies that CDP is
operational; however, pings between the two interfaces are unsuccessful. What is the
cause of this connectivity problem?
no set loopback
incompatible bandwidth
incorrect IP address on R1
incompatible encapsulation
44
Which two statements are true regarding a PPP connection between two Cisco routers?
(Choose two.)
Refer to the exhibit. All routes in the exhibit are available to a router. Which two routes will
be placed into the routing table? (Choose two.)
46
Which two criteria are used by STP to select a root bridge? (Choose two.)
memory size
bridge priority
number of ports
switch location
switching speed
47
Refer to the exhibit. What two conclusions can be drawn from the displayed output?
(Choose two.)
A packet with a destination IP address of 172.20.1.14 will exit the router via the Serial 0/1/0
interface.
Network 172.20.1.4 can be reached through two possible routes of equal cost.
The router connected to Serial 0/1/1 is advertising four separate routes through EIGRP to
this router.
48
Refer to the exhibit. The network is using OSPF as the routing protocol. A network
administrator issues the show ip ospf neighbor command to check the status of operation.
Which statement is true?
RA and RB can not form an adjacency because they are stuck in the 2-way state.
49
Hosts A and B can reach each other, but cannot reach hosts C and D or the server.
Hosts A, B, C, and D can reach each other, but cannot reach the server.
50
Refer to the exhibit. Assuming that all three routers are configured with the EIGRP routing
protocol and sharing information, what information can be gathered from the show
command output?
51
A sales representative is preparing to send sensitive information to corporate headquarters
from a hotel room using the Internet. Prior to the trip, the IT staff made the necessary
provisions to allow secure Internet access. What solution was implemented for the sales
representative?
VPN
Frame Relay
52
Refer to the exhibit. A network administrator wishes to deny Internet access to all R2 LAN
hosts, while allowing these hosts to reach all other devices on the company networks.
Where should the ACL shown in the exhibit be placed to meet these requirements?
53
Which three statements are true about RSTP? (Choose three.)
RSTP can fall back to STP to provide support for legacy equipment.
RSTP views all ports that are not discarding as part of an active topology.
54
A company is using a Class B IP addressing scheme and expects to need as many as 150
networks. What is the correct subnet mask to use with the network configuration?
255.255.0.0
255.255.240.0
255.255.254.0
255.255.255.0
255.255.255.128
255.255.255.192
55
A sales representative is using a wireless connection to make a VoIP call. Which protocol
will be used to transport the voice packets?
TCP
UDP
PPP
HDLC
56
Refer to the exhibit. What is the purpose of the command: RouterA(config)# access-list 1
permit 192.168.16.0 0.0.0.255?
It identifies traffic on all inside interfaces to be translated and given access to the ISP
router.
It identifies traffic from the fa0/1 interface to be translated and given access to the ISP
router.
It allows traffic from the ISP to reach all of the inside interfaces.
It identifies traffic from the fa0/0 interface to be translated and given access to the ISP
router.
57
Refer to the exhibit. Server7 has been added to the server farm network. The hosts can
ping Servers 2 and 3 and Server2 and Server3 can ping each other. Server7 cannot ping
the other servers connected to the switch. What is the cause of this problem?
The switch port used for Server7 is not in the same VLAN as Server2 and Server3.
The Fa0/0 interface of the router has not been configured for subinterfaces to support inter-
VLAN routing.
58
Which three IP addresses are valid host addresses in the 10.200.0.0/20 network? (Choose
three.)
10.200.11.69
10.200.16.1
10.200.0.255
10.201.0.55
10.200.15.240