Escolar Documentos
Profissional Documentos
Cultura Documentos
Outline:
-Built-up beams
1. Shear stress
Imagine that boards are stacked on top of each other as shown in Figure 1. In the first case there is no
bond between the boards so that during deformation they can slip over each other. In the second case the
boards are bonded together (by means of glue or nails) so that they doe not slip over each other and act
together as one unit.
(a) No bond between the boards (b) Boards are bonded together
Fig. 1 Beams stacked on top of each other
What is preventing slip in between the boards is the shear stress carried by the bond (glue or nails) as
shown in Figure 2.
(a) Slip between the unbonded boards (b) Shear stress between the bonded boards
As illustrated for the simply supported beam in Fig 1.a, when the boards slip over each other, at the
interface of the two boards the ends of the board on the top gets a head of the ends of the board on the
bottom as shown in Fig. 2(b). When the boards are bonded in order to prevent slip, the shear stress acting
at the bottom surface of the top board is pulling the ends of the beam back, on the other hand the stresses
1
Mechanics of Solids Dr Emre Erkmen
Lecture 5 1
acting at the top surface of the bottom beam is pushing the ends of the beam forward as shown in Fig.2 so
that they stay together as in Fig1. b.
Consider a small segment ∆x isolated from the loaded beam as shown in the Fig.3.
Vertical loads will cause internal shear force and bending moment. In Fig.4 notice that the internal forces
and the applied load are shown according to the positive sign convention on both sides of the beam
segment. If at x the internal shear force is V and bending moment is M, then at x + ∆x , they are V + ∆V
and M + ∆M because in general, for different coordinates along the axis of the beam there will be
different shear force and bending moments. Because ∆x is small, ∆M and ∆V are also small.
∆x
( M + ∆M ) − M − (V + ∆V ) ∆x − q∆x =0
2
Because ∆x is small, the terms ∆x 2 and ∆x∆V are very small so that they are negligible. As a result from
the equation above we can obtain a relation between the increment in the moment and the shear force as
∆M = V ∆x
The above equation states that if there is no internal shear force (due to applied loading) there is no
change in the bending moment.
Lecture 5 2
Longitudinal shear stress
The above equation states that if there is no internal shear force (due to applied loading) there is no
change in the bending moment.
My
By using the bending formula that we derived in lecture 4, i.e. σ = − we can express the normal
I
stresses acting on the left and right cross-sections as shown in Fig. 5.
σt σ t + ∆σ t
M y M+ M
NA
V V+ V
b b
b x
Notice that at coordinate is x the stress at the top fibre is σ t and at the bottom fibre is σ b due to internal
bending moment M, which become σ t + ∆σ t at the top fibre and σ b + ∆σ b at the bottom fibre is at
coordinate x + ∆x due to change in the bending moment.
If we cut the segment horizontally (shown with the dotted line in Fig.5) and consider the longitudinal
equilibrium for the free-body shown in Fig. 6 a, since the normal stress distribution is different on the left
and right cross-sections there should be an equivalent force acting on the bottom surface in tangential
direction Fs ,
q
σt σ t + ∆σ t
Fs
Fig. 6 Free-body diagram of a piece cut from the beam
Lecture 5 3
Consider the forces acting in the axial direction as shown on the Free-body diagram in Fig. 7. The cross-
sectional area of the piece cut from the segment ∆x is shown as A’.
σ = − My
I
A’
dA
y
σ + ∆σ = −
( M + ∆M ) y
∆x I
b
Fs Neutral axis
Fig. 7 Free-body diagram shown in perspective (only the forces in axial direction are shown)
Fs + ∫ (σ + ∆σ )dA − ∫ σ dA = 0
A' A'
By using the bending formula, stresses at a distance y from the neutral axis can be expressed in terms of
the moments and the above equations becomes
M + ∆M M ∆M
Fs = ∫ ydA − ∫ y dA = ∫ ydA
A'
I A' I A'
I
Notice that the width is shown as b in Fig. 7, and as in Lecture 4 the axis is passing through the neutral
axis. Also note that the cut of with be is not necessarily at the neutral axis. In Fig. 7, indeed it is a cut
above the neutral axis (also check Fig.5).
Remember from lecture 1 that the shear stresses τ can be calculated from the shear force Fs as
Fs
τ=
b∆x
From the above two equations the average shear stress at the cut surface can be expressed as
∆M V
τ=∫ ydA when ∆x → 0 τ=∫ ydA
A'
∆xbI A'
bI
When obtaining bending stresses we imposed kinematic conditions because it was a statically
indeterminate problem. When obtaining shear stresses we did not impose any further kinematic
conditions and we used only equilibrium. Thus obtaining shear stresses is a statically determinate
problem.
Lecture 5 4
New definition related to the cross-section
Since the shear force V, the moment of inertia I and the width b is independent of the coordinate y of a
point on the cross-section that is under axial stress, in the shear stress formula we can take them out of the
integration.
V V
τ=
bI ∫ ydA = bI Q
A'
The integral term (which will be shown as Q ) is the first moment of the cut area with respect to the
neutral (centroidal) axis of the whole section. The first moment of area can be written as
Q = yA '
in which y is the distance of the centroid of the cut section with area A’ to the neutral axis of the whole
section as shown in Fig. 8..
A’
Centroid of Area A’
Fig. 8 Distance from the neutral axis to the centroid of the cut section
Shear flow q is defined as the shear force per unit length, i.e
F V
q= s when ∆x → 0 q= Q
∆x I
Summary
VQ VQ
Shear stress: τ= Shear flow: q=
bI I
V is the internal resultant shear force, determined from the method of section and
equilibrium.
I is the moment of inertia of the entire cross-sectional area about the neutral axis.
b is the width of the member’s cross sectional area, measured at the point where
shear stress is to be determined.
Lecture 5 5
Summary of the procedure for finding longitudinal shear stress or shear flow
1. Determine the location of the neutral axis and calculate the moment of inertia I of the entire cross
sectional area about the neutral axis
2. Pass an imaginary horizontal section through the point where the shear stress (or flow) is to be
determined.
3. Measure the width of the area at this section
4. Calculate the first moment Q for the area laying either above or below the section
Example
Solution
Based on the plan view shown below it can be discussed that if the planks were glued together, on the
glue a shear force of F would be acting for a span of L cut from the beam. That force should now be
shared by nails.
q F q
Fn
L
For the given I shape cross-section the moment of inertia can be calculated as
Lecture 5 6
I = 121 ( 0.020 m )( 0.100 m ) + 2[ 121 ( 0.100 m )( 0.020 m ) + ( 0.020 m × 0.100 m )( 0.060 m ) ]
3 3 2
= 16.20 ×10−6 m 4
Calculating the first moment of area is the part of the solution that one must be most careful about since it
depends on the cut.
We are interested in the shear flow between the two planks, so we cut from there and look under the top
plank which forming the top flange. In this case the area above the cut is the area of the top flange.
Q = A' y
Q = ( 0.020 m × 0.100 m )( 0.060 m ) = 120 × 10−6 m3
(500N)(120 × 10−6 m3 )
q= = 3704 N
16.20 × 10 m
-6 4 m
For a length of L=25mm the shear flow will be equivalent to a shear force Fn = qL which is the area that
each nail covers, i.e.
Fn = (0.025 m)q = (0.025 m)(3704 N m = 92.6 N
What about the nail connecting the bottom flange with the web?
Lecture 5 7
Q = ( 0.020 m × 0.100 m )( −0.060 m ) = −120 ×10−6 m3
500 × (−120 ×10−6 )
q= = −3704 N The change of sign means the shear flow is in the opposite direction
16.20 × 10-6 m
Fn = (0.025 m)q = (0.025m)(−3704 N m = −92.6 N Since the section is symmetric about N.A the shear
force in each nail is same as the top nails however the direction is different,
Example
Find the shear flow in the welds holding a 150x10 plate on the top flange of the T-beams shown below to
carry 100N shear force.
150
10
11.36
C z welds
78.64
Izz = 2.084 x 106 mm4
Solution
The welds are providing the necessary shear force to hold the plate and the top flange together.
That means we should take a cut in between the plate and the top flange and look under the plate.
Thus the area that we should consider for the first moment of area Q is as shown in the figure below.
150
10
11.36 16.36
N.A
VQ 100 × 24,540
q= = = 1.178 N / mm
I 2.084 × 106
q / 2 = 0.59 N/mm
Lecture 5 8
Shear stress distribution on the cross-sectional surface
Can we find the shear stress distribution across the section (similar to the bending stresses in Lecture 4)?
dz
∆x Fs τ dy
τ
b
Fs
∆x
V dx
C C
By using the expression developed for the longitudinal shear stresses (in x direction) acting at the cut
surface we can find the shear stress distribution across-the section (in y direction).
For this purpose we should consider the moment equilibrium cut from the segment whose front surface is
on the cross-sectional surface and top surface is at the intersection of the top and bottom components.
As shown in the side view of this cube in Fig. 10 the shear stress acting at the intersection surface is
τ x and the shear stress acting at the front surface is τ y .
τx
dy τy
∑M A = 0 → (τ x dxdz ) × dy − (τ y dydz ) × dx = 0
From which we obtain τ x = τ y . Thus, longitudinal shear stress always has its associated transverse shear
stress acting on the cross-section and two stresses are equal.
Lecture 5 9
Shear stress distribution for rectangular section
Take a in a beam of solid rectangular cross section with width b and height h transmitting a vertical shear
V as shown in Fig. 11.
y
Neutral axis
The distribution of the shear stress throughout the cross section can be determined by computing the
shear stress at an arbitrary height y from the neutral axis as shown in Fig.12
VQ
τ=
bI
The first moment of area according to this arbitrary cut can be written as
1h h 1 h2
Q = A ' y ' = y + − y − y b = − y 2 b
2 2 2 2 4
VQ 6V h 2
τ= = 3 − y2
Ib bh 4
Thus, the shear stress is a quadratic function of y based on which the distribution across the section can be
shown as in Fig. 13.
Lecture 5 10
Fig. 13 Shear stress distribution on the rectangular cross-section
The minimum value is at the top and the bottom of the section , where y = h/2 → τ min = 0
6V h 2 3V V
The maximum value is at the neutral axis, where y = 0 → τ max = 3
= = 1.5
bh 4 2bh A
V
Remember the average shear stress is τ average =
A
The maximum shear stress is 50% greater than the average shear stress!
Example
A cantilever beam of length L=2m supports a load P=8kN. The beam is made of wood with cross-
sectional dimensions 120mm x 200mm. Calculated the shear stresses due to the load P at points located
25mm, 50mm, 75mm and 100mm from the top surface of the beam. From these results, plot a graph
showing the distribution of shear stresses from top to bottom of the beam
For rectangular sections we know that the shear stress distribution can be calculated as
6V h 2
τ= 3
− y2
bh 4
Lecture 5 11
Based on the above formula for shear stress distribution we can write
8000 2002
τ= 6
− y2
160 × 10 4
Similar to rectangular sections the shear stress is a quadratic function of the y coordinate, however
because of the sudden change in the width b, a jump occurs on the shear stress distribution as shown in
Fig. 15.
Lecture 5 12
Example
A wide-flange I beam is subjected to shear force of V=80kN. Plot the shear stress distribution acting over
the beam’s cross-sectional area. Also, determine the shear force resisted only by the web.
Solution
The shear-stress distribution will be parabolic and due to symmetry only the shear stresses at points B’,
shown in the figure below and the centroid of the whole section will be computed.
= 155.6 ×10−6 m 4
At point B’, width is b=0.3m and A’ is the dark shaded area shown in the figure above. The first moment
area can be calculated as
VQ 80 × 0.66 ×10−3
τ= = = 1.13 MPa
Ib 156 ×10−6 × 0.3
At point B, width is b=0.015m. A’ is the same dark shaded area shown in the figure above and because of
that the first moment area is the same as Q = yA′ = 0.66 × 10−3 m 3 .
Lecture 5 13
The shear stress at point B can be calculated as
VQ 80 × 0.66 × 10−3
τ= = = 22.6 MPa
Ib 156 × 10−6 × 0.015
At the centroid of the I-section the width is b=0.015m. The first moment of area can be calculated as
VQ 80 × 0.74 × 10−3
τ= = = 25.2 MPa
Ib 156 × 10−6 × 0.015
2
The shear force resisted only by the web Vweb = 22.6 × (15 × 200 ) + ( 25.2 − 22.6 ) × (15 × 200 ) = 73kN
3
91% of the shear force is carried by the web. Usually in thin-walled beams web carry the most of the
vertical shear force acting on the cross-section.
What if the shear flow (or stress) that we are concerned with is not the one on horizontal surface as in Fig
16 a but on the vertical surface as in Fig. 16b.
(a) Vertical nails are needed (b) Horizontal nails are needed
Fig. 16 Built-up sections
Lecture 5 14
In cases where we need to connect to pieces whose contact surface is vertical we can still determine the
shear flow (or stress) according to a vertical cut as shown in Fig. 17.
(a) I-section subjected to shear force (b) Free-body of a piece cut from the flange
In order to keep the dark shaded part shown in Fig. 17 a to the rest of the flange there has to be shear flow
acting as shown in Fig. 17 b. Similar to the previous calculations this shear flow can be calculated from
the longitudinal equilibrium of the free-body shown in Fig. 17 b.
At the front surface normal stresses due to bending moment add up to an equivalent force of F + ∆F . At
the back surface the normal stresses add up to an equivalent force of F. The shear flow on the side occurs
in order to balance that difference ∆F in longitudinal direction. If ∆x → 0 then ∆F → dF
Example
Nails having a total shear strength of 40 kN are used in a beam that can be constructed either as in the
case I or case II. If the nails are spaced at 9cm, determine the largest vertical shear that can be supported
at each case so that the fastener will not fail.
Lecture 5 15
Since the geometry is same in both cases the moment of inertia is the same, which can be obtained as
Case I
An horizontal cut that is the contact surface between the web and the flange should be made in order to
determine the shear flow
Thus whole flange should be considered in calculating the first moment of area
The shear strength of a nail is 40N which covers a span of 9cm. In this case the shear flow that can be
carried by the nails can be calculated as
VQ 40 V × 3.375
q= = =
I 9 20.58
From the above equation the shear force capacity can be calculated as V = 27.1N
Case II
A vertical cut that is the contact surface between the web and half the flange should be made in order to
determine the shear flow.
The shear strength of a nail is 40N which covers a span of 9cm. In this case the shear flow that can be
carried by the nails can be calculated as
VQ 40 V × 1.125
q= = =
I 9 20.58
From the above equation the shear force capacity can be calculated as V = 81.3 N
Lecture 5 16
Example
The timber beam is fabricated of four 30x150 mm boards glued together to form a box section 150mm
wide and 210mm deep. Maximum allowable shearing stresses in the timber and in the glue are 1.2N/mm2
and 0.8N/mm2 respectively. Determine the maximum possible value of w.
w kN/m 30mm
1.5w kNm
A C B 150mm
3m 3m 1m
30mm
As the first step maximum shear force that is acting along the beam should be calculated.
For this, the shear force diagram has to be drawn to pick the maximum shear force.
∑F Y =0→ R A +R B = 3w → R A = 2w
Lecture 5 17
Shear force diagram
The moment of inertia around the neutral axis of the box section can be calculated as
1
I= 150 × 2103 − 90 ×1503 = 90.45 ×106 mm 4
12
If the failure is assumed to occur in timber then the maximum shear stress occurs when y=0, because te
first moment of area Q is maximum.
If the failure is assumed to occur in the glue the shear stress should be calculated at the contact surface.
Lecture 5 18