Escolar Documentos
Profissional Documentos
Cultura Documentos
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445 STYLE NUMBER: FW8307WT
www . quoizel . com
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (1) 100W A19 medium base bulb .
● Helpful Tools (not included): Wire strippers.
1 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FW8307WT
STEP 1:
a. Locate the Shade inside of the Cage, over the Socket. Lock Screw
b . Attach the Tab onto the Shade lip, line up the hole on it Tab
onto the Mounting Hole on the top edge of the Cage.
Using screwdriver, thread the Lock Screw into the
Mounting Hole and hand-tighten until snug to secure
the Shade.
Shade
Mounting
Hole
Cage
Socket
STEP 2:
a. Install the correct bulb referring to fixture markings and/or labels for maximum wattage.
2 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FW8307WT
STEP 3:
a. Locate the Bolts in the bottom of the Fixture Hood
through the holes on the top edge of the Cage. Secure Fixture
by threading the Lock Balls onto the Bolts. Hand- Hood
tighten until snug.
Bolt
Lock
Ball
Cage
STEP 4:
a. Screw the Mounting Screws into the Crossbar, place Mounting Screw
Crossbar
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as Hex Nut
shown. Secure the position of the Mounting Screws by
tightening the Hex Nuts against the Crossbar.
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws.
Lock Washer
Outlet Box
Outlet Box Screw
STEP 5:
Use Wire Connectors (not supplied) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires.
a. Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side). BLACK (OR RED) WIRE BLACK OR SMOOTH
c. Connect the House Black (or Red) Wire to the Fixture FROM FIXTURE
FROM HOUSE
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the GROUND WIRE GROUND WIRE
Outlet Box.
FROM HOUSE FROM FIXTURE
3 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FW8307WT
Mounting
Screw
Backplate
STEP 7:
a. Refer to the following information for caulking instructions:
MOUNTING BALL
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation instructions,
proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking. Using
EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were the FIXTURE
BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of backplate and down
other side. DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE to ensure proper moisture drainage.
4 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER: FW8307WT
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5 OF 5