Escolar Documentos
Profissional Documentos
Cultura Documentos
Frigorficos
Instrucciones de seguridad ............................................. 3 Cmo conectar la electricidad ......................................... 4 Los controles de temperatura ......................................... 5 El filtro de agua ................................................................ 6 Puertas del frigorfico ...................................................... 6 Estantes y recipientes ..................................................... 7 El compartimiento del congelador ................................... 9 Cajones y recipientes .................................................... 10 Cmo retirar los cajones ............................................... 10 Dispositivo automtico para hacer hielo ........................ 11 Dispensador de agua y hielos ...................................... 12 Cuidado y limpieza ........................................................ 12 Reemplazo de bombillas .............................................. 14 Instrucciones de instalacin .......................................... 15 Conexin a la toma de agua ......................................... 18 Sonidos normales de operacin .................................... 20 Antes de solicitar servicio .............................................. 21
Side by side
Escriba el modelo y los nmeros de serie aqu: Nmero de modelo Nmero de serie Estos nmeros se encuentran dentro del compartimento del frigorfico en la parte superior derecha.
PRECAUCIONES DE SEGURIDAD
Al utilizar aparatos elctricos se deben acatar un nmero de precauciones de seguridad bsicas, tales como: Antes de iniciar su utilizacin, este frigorfico debe instalarse y ubicarse correctamente de acuerdo con las Instrucciones de Instalacin. Tambin vea la seccin Cmo conectar la electricidad. No permita que los nios se suban o se cuelguen de los estantes del frigorfico. Podran daarlo y recibir heridas graves. No toque las superficies fras del compartimento del congelador si tiene las manos hmedas o mojadas. Su piel podra quedar adherida a estas superficies extremadamente fras. No almacene o use gasolina u otros vapores o lquidos inflamables cerca de este u otros aparatos elctricos. En los frigorficos con dispositivos automticos para hacer hielo, evite cualquier tipo de contacto con las piezas mviles del mecanismo eyector, o con el elemento de calefaccin ubicado en la parte inferior del dispositivo para hacer hielo. No toque este ltimo mecanismo mientras el frigorfico est enchufado. La instalacin del dispositivo para hacer hielo debe realizarla un tcnico calificado. Mantenga los dedos fuera de las "reas de pellizco"; los espacios entre las puertas y entre las puertas y el cuerpo del frigorfico son necesariamente pequeos. Tenga cuidado al cerrar las puertas cuando haya nios cerca. Desenchufe el frigorfico antes de limpiarlo y de hacer cualquier clase de reparacin. NOTA: Ante la necesidad de llevar a cabo alguna clase de reparacin, recomendamos enrgicamente que un tcnico calificado sea el encargado de realizarla. Antes de reemplazar una bombilla de luz quemada, el frigorfico debe desenchufarse a fin de evitar el contacto con un filamento con corriente elctrica. (Una bombilla de luz quemada puede romperse mientras se la reemplaza). NOTA: Aunque la configuracin de los dos controles se encuentre en 0 (apagado) todava hay electricidad en el circuito de la luz. No vuelva a congelar alimentos que se hayan descongelado por completo.
Refrigerantes
Todos los aparatos de refrigeracin contienen refrigerantes, los cuales se deben retirar antes de la eliminacin del producto de acuerdo con la ley. Si va a desechar algn aparato antiguo de refrigeracin, consulte con su Ayuntamiento. Este electrodomstico no est diseado para ser utilizado por personas con capacidades fsicas, sensoriales o mentales limitadas (nios incluidos), o que carezcan de la experiencia y el conocimiento necesarios, a menos que estn supervisados por una persona encargada de velar por su seguridad o hayan sido instruidas en la utilizacin del electrodomstico. Supervise a los nios para asegurarse de que no juegan con el aparato.
ADVERTENCIA!
CMO CONECTAR LA ELECTRICIDAD
Si el cable de alimentacin sufre algn tipo de dao, un representante del Servicio de Asistencia Tcnica de FAGOR debe reemplazarlo a fin de evitar un riesgo para la seguridad. Nunca desenchufe el frigorfico tirando del cable de alimentacin. Siempre tome con firmeza el enchufe del frigorfico y retrelo de la toma de corriente de la pared. Repare o reemplace inmediatamente todos los cables de alimentacin que se hayan desgastado o daado. Nunca utilice un cable que tenga daos por abrasin en toda su extensin o en los extremos del mismo. Cuando aleje el frigorfico de la pared, asegrese de no aplastar o daar el cable de alimentacin.
Antes de usar, asegrese de que exista una apropiada conexin a tierra
Los controles de la temperatura vienen preconfigurados de fbrica a 5 para los compartimientos del frigorfico y del congelador. Para ajustar la temperatura, pulse el botn "+" (ms caliente) o "-" (ms fro) en el lateral del congelador o del frigorfico. La luz de ajuste se encender. Pulse "+" (ms caliente) o "-" (ms fro) hasta alcanzar el ajuste deseado. Puede que sea necesario hacer varios ajustes. Cada vez que usted que usted ajuste los controles, deje pasar 24 horas desde el ajuste para que el frigorfico alcance el ajuste que usted ha seleccionado. Ajustar uno o ambos controles en 0 (apagado), detiene la refrigeracin tanto en el compartimento del frigorfico como en el del congelador, pero no interrumpe el suministro elctrico del frigorfico. Las configuraciones de los controles pueden variar dependiendo de las preferencias personales, uso y condiciones de funcionamiento, y pueden requerir ms de un ajuste. NOTA: El frigorfico se enva con una pelcula de proteccin que cubre los controles de la temperatura. Si esta pelcula no se retir durante la instalacin, hgalo ahora.
NOTA: La temperatura interna puede verse afectada por factores como la ubicacin del aparato, la temperatura ambiente y la frecuencia con que se abren las puertas. Ajuste los controles de temperatura segn lo requiera a fin de compensar estos factores.
El filtro de agua.
Instalar el cartucho del filtro
El cartucho del filtro de agua est ubicado en la esquina superior derecha trasera del compartimento del frigorfico. 3. Alinee la flecha del cartucho con el soporte del cartucho. Coloque la parte superior del nuevo cartucho hacia arriba dentro del soporte. No empuje el cartucho hacia arriba a dentro del soporte. 4. Gire el cartucho lentamente hacia la derecha hasta que el cartucho se pare. NO APRETAR MUY FUERTE. Mientras est girndolo, ste se alzar por s mismo en su posicin. El cartucho girar aproximadamente 1/2 de vuelta. 5. Deje correr el agua desde el dispensador durante 5 minutos para aclarar el sistema y para prevenir salpicaduras. NOTA: Un cartucho del filtro del agua recin instalado podra causar prdida de agua desde dispensador.
Soporte de cartucho
Ponga la parte superior del cartucho hacia arriba dentro del soporte del cartucho y grelo lentamente hacia la derecha.
Filtros de recambio: Para pedir cartuchos adicionales, pngase contacto con el distribuidor local.
Para remover este estilo de estante: 1. Levante el lado izquierdo del estante y deslcelo hacia la izquierda en el centro de los estantes de apoyo. 2. Gire el lado derecho del estante hacia arriba y hacia afuera de los estantes de apoyo.
El rendimiento del congelador est evaluado por calificaciones de estrellas definidas por el ESTNDAR Y RESUMEN ISO 8561 ESPECIFICADO A CONTINUACIN: TEMPERATURA DE LA CARGA CONGELADA (TEMPERATURA DE LOS ALIMENTOS) Por debajo de 6C. Por debajo de 12C. or Por debajo de 18C. 86
CDIGO:
Cajones y recipientes.
No todos los modelos tienen todas las caractersticas.
10
Tire de la parrilla superior del congelador hacia afuera para acceder al dispositivo de hacer hielo. Cercirese de reemplazar siempre la parrilla; puede usarse para almacenamiento.
2. Incline el compartimento para acceder al hielo o al interruptor de corriente. NOTA: Para poder aprovechar todas las ventajas del compartimiento inclinable de hielo, en la bandeja situada bajo el compartimento del hielo coloque exclusivamente elementos que no sean ms altos que el punto ms bajo del compartimento.
11
Alarma de puerta
La alarma de puerta suena si cualquiera de las puertas se mantiene abierta durante ms de 3 minutos. La alarma dejar de sonar tras cerrar la puerta. En los modelos con LCD, aparecer una pantalla emergente. La alarma puede silenciarse tocando la pantalla LCD.
Recogedor
Para bloquear el dispensador Presione el botn LOCK o LOCK CONTROL (control de bloqueo) durante 3 segundos para cerrar el dispensador y el panel de control. Para desbloquearlo, presione de nuevo el mismo botn durante 3 segundos.
12
En caso de mudanza
Asegure todos los elementos sueltos como entrepaos y recipientes pegndolos con cinta adhesiva en su lugar para evitar daos. Al usar una carretilla para mover el frigorfico, no haga descansar la parte frontal o trasera del frigorfico contra la carretilla. Esto podra daar el frigorfico. Manjelo slo desde los laterales del frigorfico. Asegrese de que el frigorfico se coloque en posicin vertical durante la mudanza.
13
Reemplazo de bombillas.
El colocar el control en posicin 0 (apagado) no remueve la corriente elctrica del circuito de la luz.
Dispensador
1. Desenchufe el frigorfico. 2. La bombilla est situada en el dispensador bajo el panel de control. Quite la bombilla girndola en sentido contrario a las agujas del reloj. 3. Cambie la bombilla por una bombilla del mismo tamao y potencia. 4. Conecte de nuevo el frigorfico a la corriente.
14
Instrucciones de instalacin
ANTES DE INICIAR
Lea estas instrucciones completa y cuidadosamente.
Frigorfico
CLAROS
Disponga el siguiente espacio para una fcil instalacin, apropiada circulacin del aire y conexiones de fontanera y elctricas: Lados: 4 mm Parte superior: 25 mm Parte posterior: 13 mm
Nota al instalador: Asegrese de dejar estas instrucciones al consumidor. Nota al consumidor: Conserve estas instrucciones para consultas posteriores. Nivel de destreza: La instalacin de este aparato requiere de destrezas mecnicas bsicas. Tiempo de ejecucin: Instalacin del frigorfico 15 minutos La instalacin apropiada es la responsabilidad del instalador. Las averas del producto causadas por una instalacin inadecuada no estn cubiertas por la garanta.
DIMENSIONES
A* B C** D E F 1733 mm 908 mm 738 mm 1156 mm 1214 mm 986 mm 1355 mm 994 mm
G H
F A
E B H D
15
Instrucciones de instalacin
RODILLOS
Los rodillos cumplen 3 funciones: Los rodillos se ajustan para hacer que la puerta se cierre con facilidad cuando est abierta aproximadamente a la mitad. (Elevando el frente a una distancia aproximada 16 mm del piso). Los rodillos se ajustan para que el frigorfico quede firmemente asentado sobre el piso y no se tambalee. Los rodillos permiten mover el frigorfico para retirarlo de la pared para su limpieza. Despus de instalar el frigorfico es necesario realizar algunos ltimos ajustes para nivelarlo. Para ajustar los rodillos: 1. Para quitar la parrilla de la base, abra las puertas, retire los tornillos de cada lado y tire de la misma hacia fuera. 2. Gire el rodillo frontal ajustando los tornillos en el sentido de las agujas del reloj para elevar el frigorfico y en el sentido contrario para bajarlo. Use una llave hexagonal de 3/ 8", o una llave de tuercas ajustable. 3. Estos modelos tienen tambin rodillos traseros ajustables para que pueda alinear el frigorfico con sus muebles de cocina. Use una llave de tubo de 5/16" de mango largo para girar los tornillos de los rodillos traseros en sentido de las agujas del reloj para elevar el frigorfico y en el sentido contrario para bajarlo. 4. Reinstale la base de la rejilla.
Para quitar la parrilla de la base, abra las puertas, retire los tornillos de cada lado de la parrilla y tire de la misma hacia fuera.
16
Instrucciones de instalacin
DIMENSIONES Y ESPECIFICACIONES
17
En modelos que usan la conexin de la vlvula de agua, retire la tapa flexible de plstico.
Coloque la tuerca de compresin y la frula (manga) al extremo del tubo, tal como se indica en la ilustracin. Inserte el extremo de la tubera en la conexin de la vlvula de agua hasta donde sea posible. Mientras usted sostiene el tubo, apriete el ajuste. Apriete la tubera en la abrazadera proporcionada para sostenerla en una posicin vertical. Quizs abrir la abrazadera requiera un pequeo esfuerzo. Una de las siguientes ilustraciones se asemejar a la conexin en su frigorfico.
18
Instrucciones de instalacin
2. ENCIENDA EL AGUA Y CONECTE EL FRIGORFICO
Arregle el rollo de tuberas para que no vibre contra la parte posterior del frigorfico o contra la pared. Empuje el frigorfico contra la pared otra vez.
NOTA: En el caso en que la presin del agua sea baja, la llave de paso del agua podra tardar hasta tres veces ms en llenar de agua suficiente el dispositivo para hacer hielo.
19
El nuevo compresor de alta eficiencia puede funcionar ms rpido y durante ms tiempo que el de su frigorfico anterior y puede escuchar un zumbido de tono alto o un sonido pulsante mientras opera. Puede escuchar un sonido de soplido cuando las puertas se cierran. Esto se debe a que la presin se est estabilizando dentro del frigorfico.
Puede escuchar los ventiladores movindose a gran velocidad. Esto pasa cuando el frigorfico se conecta por primera vez, cuando las puertas se abren frecuentemente o cuando se guarda gran cantidad de alimentos en los compartimientos del frigorfico o del congelador. Los ventiladores estn ayudando a mantener las temperaturas correctas. Si cualquiera de las puertas permanece abierta por ms de 3 minutos, puede escuchar los ventiladores para enfriar los focos de luz. Los ventiladores cambian la velocidad para suministrar enfriamiento ptimo y ahorrar energa.
SONIDOS DE AGUA
El fluido del refrigerante a travs de las bobinas puede producir un sonido de borboteo como de agua hirviendo. El agua que cae en el calentador de descongelacin puede causar un chisporroteo, estallido o zumbido durante el ciclo de descongelacin. Un ruido de agua cayendo se puede escuchar durante el ciclo de descongelado a medida que el hielo se derrite desde el evaporador y fluye hacia la bandeja de drenaje. El cierre de las puertas puede producir un sonido de gorgoteo debido a la estabilizacin de la presin. Para informacin adicional acerca de los sonidos de operacin de los dispositivos para hacer hielo o de los dispensadores de agua, consulte las secciones "El dispositivo automtico para hacer hielo" y "El dispensador de agua y hielo".
20
Causas posibles
Frigorfico en ciclo de descongelar. El control o controles de temperatura en posicin 0 (apagado). El frigorfico est desconectado. Fusible fundido/interruptor de circuito roto. El frigorfico est en el modo de exhibicin.
Qu hacer
Espere 30 minutos para que la descongelacin se termine. Mueva los controles de temperatura hasta un ajuste la de temperatura. Empuje el enchufe a fondo en la toma de corriente. Cambie el fusible o reajuste el interruptor. Desconecte el frigorfico y enchfelo otra vez. Consulte la seccin "Rodillos". Espere 24 horas para que el frigorfico se enfre completamente. Eso es normal. Revise si un paquete mantiene la puerta abierta. Eso es normal. Consulte la seccin "Controles". Consulte la seccin "Controles". Coloque el control de temperatura un paso ms fro. Consulte la seccin "Controles". Revise si hay un paquete que mantiene la puerta abierta. Revise si hay un paquete que mantiene la puerta abierta.
Vibraciones o sacudidas (una vibracin ligera es normal) El motor trabaja por periodos prolongados o arranca y se detiene con frecuencia. Los frigorficos modernos con un espacio de almacenamiento mayor y un congelador ms grande requieren de un tiempo ms largo de operacin. Arrancan y se detienen frecuentemente para mantener temperaturas uniformes) Compartimento del frigorfico o del congelador demasiado clido
Los rodillos requieren un ajuste. Es normal cuando el frigorfico se acaba de instalar en su casa. Ocurre cuando hay grandes cantidades de alimentos en el frigorfico. Se dej abierta la puerta. Clima caluroso o aperturas frecuentes de la puerta. Controles de temperatura colocados en el punto ms fro. El control de la temperatura no se coloc en una posicin suficientemente fra. Clima caluroso o aperturas frecuentes de la puerta. Se dej abierta la puerta.
Escarcha o cristales de hielo sobre alimentos congelados (la escarcha dentro de los paquetes es normal) El divisor entre el compartimento del frigorfico y del congelador se siente tibio Dispositivo automtico para hacer hielo no funciona
Se dej abierta la puerta. Aperturas de puertas demasiado frecuentes o largas. El sistema automtico de ahorro de energa hace circular un lquido tibio por la parte delantera del congelador. El interruptor de alimentacin elctrica del dispositivo automtico para hacer hielo est en la posicin de apagado. El agua est cerrada o no est conectada. El compartimento del congelador es muy clido. Cubos apilados en el recipiente apaga el dispositivo para hacer hielo. Cubos de hielo atascados en dispositivo para hacer hielo. (La luz verde de corriente en dispositivo de hielo est destellando).
Coloque el interruptor de alimentacin elctrica en la posicin de encendido. Vea Instalar la lnea de agua. Espere 24 horas para que se enfre el frigorfico. Nivele los cubos con la mano. Apague el dispositivo de hielo, retire los cubos y vuelva a poner el dispositivo en marcha.
21
Problema
Zumbido frecuente
Causas posibles
El interruptor del dispositivo para hacer hielo est en la posicin de encendido, pero el suministro de agua hacia el frigorfico no est conectado. El recipiente para los cubos necesita limpieza. Alimentos transmitiendo olor/sabor a los cubos. El interior del frigorfico requiere limpieza.
Qu hacer
Fije el interruptor de corriente en la posicin de apagado; mantener el interruptor en la posicin de encendido daar la vlvula del agua. Vace y limpie el recipiente. Deseche los cubos. Envuelva bien los alimentos. Vea Cuidado y limpieza. Reemplace el cartucho del filtro por uno nuevo o instale un tapn. Revise si hay un paquete que mantiene la puerta abierta. Consulte la seccin "Controles".
Filtro de agua obstruido. Se dej abierta la puerta. El control de temperatura no es suficientemente fro.
Dispositivo de hielo apagado o suministro de agua est cerrado. Los cubos de hielo se congelaron sobre el brazo sensor. Bloques irregulares de hielo dentro del contenedor de almacenamiento.
Encienda el dispositivo de hielo o abra el suministro agua. Remueva los cubos de hielo. Rmpalos con los dedos y deseche los cubos restantes. El congelador puede estar demasiado clido. Ajuste el control a una posicin ms fra una posicin a la vez hasta que no se formen bloques. Presione el botn LOCK CONTROL (BLOQUEAR CONTROLES) durante tres segundos. Dispense agua hasta que todo el sistema del agua se llene de nuevo. Espere 24 horas para que el frigorfico se enfre por completo. Dispense el agua hasta que todo el sistema del agua se haya renovado. Deje pasar varias horas para que el suministro repuesto se enfre. Consulte "Instalando la lnea de agua". Reemplace el cartucho del filtro o retire el filtro e instale un tapn. Presione el brazo del dispensador por dos minutos por lo menos. Presione el botn LOCK CONTROL (BLOQUEAR CONTROLES) durante tres segundos. Deje correr el agua desde el dispensador durante 3 minutos (aprox. 6 litros). Llame al servicio tcnico. Coloque el control de temperatura en una posicin ms clida.
El dispensador de agua no se ha usado por mucho tiempo. Normal con un frigorfico recin instalado. El dispensador de agua no se ha usado por mucho tiempo. El sistema de agua se ha drenado
Lnea de suministro de agua cerrada o no conectada. Filtro de agua obstruido. Aire atrapado en el sistema de agua. El dispensador est BLOQUEADO.
El agua en el depsito est congelada. El control de temperatura est en una posicin demasiado fra.
22
Problema
No sale agua y no hay produccin de cubos de hielo
Causas posibles
Lnea de agua o llave de paso obstruidas. Filtro de agua obstruido. El dispensador est BLOQUEADO.
Qu hacer
Llame a un fontanero. Reemplace el cartucho del filtro o remueva el filtro e instale un tapn. Presione el botn LOCK CONTROL (BLOQUEAR CONTROLES) durante tres segundos. Se quedaron unos cuantos cubos en el triturador, de la seleccin anterior. Esto es normal.
Se seleccion CUBED ICE (HIELO EN CUBOS) pero se dispens CRUSHED ICE (HIELO PICADO). Brillo anaranjado en el congelador El frigorfico huele
El calefactor de descongelado est encendido. Alimentos transmitiendo olores al frigorfico. El interior requiere limpieza.
Eso es normal.
Los alimentos de olor fuerte deben estar tapados. Guarde una caja abierta de bicarbonato de sodio en el frigorfico; cmbiela cada tres meses. Consulte "Cuidado y limpieza". Aplique cera de parafina contra la cara del empaque.
El empaque de la puerta del lado de la bisagra se pega o se dobla sobre s mismo. Un anaquel de la puerta est chocando con unas de las parrillas dentro del frigorfico.
Se forma humedad en el exterior del frigorfico Se acumula humedad en el interior (en clima hmedo el aire lleva humedad al interior del frigorfico al abrir las puertas). La luz interior no funciona
Normal durante perodos con alto grado de humedad. Se abren las puertas con demasiada frecuencia o durante demasiado tiempo. No hay energa en el contacto elctrico. Bombilla fundida.
Seque la superficie.
Reemplace el fusible o reacondicione el disyuntor de circuitos. Consulte la seccin "Reemplazando las bombillas". Empuje los cubos hacia el vertedero con una cuchara de madera.
Agua en el piso de la cocina o en el fondo del congelador Sale aire caliente por la parte inferior del frigorfico
Cubos de hielo atrapados en el conducto. Flujo normal de aire para enfriar el motor. En el proceso de refrigeracin es normal que salga calor por la parte inferior del frigorfico. Algunos recubrimientos de piso son demasiado sensibles y se decoloran a estas temperaturas, que son normales y seguras. El sistema de descongelado adaptivo mantiene al compresor funcionando cuando se abren las puertas. Una puerta est abierta.
El frigorfico nunca se apaga pero las temperaturas estn bien El frigorfico pita
Esto es normal. El frigorfico se apaga despus de que la puerta permanece cerrada por 2 horas. Cierre la puerta.
23
Problema
Los alimentos no se descongelan o enfran
Causas posibles
Envoltorio. Seleccin incorrecta de peso. Alimento con alto contenido de grasa. No est usando la bandeja para enfriar o descongelar.
Qu hacer
Aumente el tiempo o envuelva de nuevo el artculo en plstico. Seleccione un peso mayor. Seleccione un peso mayor. Coloque los alimentos en la bandeja y deje espacio entre ellos para permitir un mejor flujo del aire. Deje que transcurran 24 horas para que el sistema se estabilice. Deje que transcurran 24 horas para que el sistema se estabilice. Deje que transcurran 24 horas para que el sistema se estabilice. Deje que transcurran 24 horas para que el sistema se estabilice. Esto es normal. Para reducir el consumo de energa elctrica, la funcin Select Temp se apaga cuando el control de temperatura del frigorfico se coloca en la posicin ms clida.
Se acaba de conectar la unidad al suministro de energa. Se dej abierta una puerta durante demasiado tiempo Se introdujo comida tibia al frigorfico. El ciclo de descongelado est en proceso
El control de temperatura del compartimiento del frigorfico est colocado en la posicin ms clida.
24
Refrigerators
Important Safety Information ......................................... 26 How to connect electricity ............................................. 27 About the temperature controls ..................................... 28 Water filter ..................................................................... 29 Refrigerator doors ......................................................... 29 Shelves and bins ........................................................... 30 Freezer compartment .................................................... 32 Crispers and pans ......................................................... 33 Automatic Icemaker ...................................................... 34 Ice and water dispenser ................................................ 35 Care and cleaning of the refrigerator ............................ 35 Replacing the light bulbs ............................................... 37 Installation Instructions ................................................. 38 Normal Operating Sounds ............................................ 43 Before you call for service ............................................. 44
Side by Side
Write the model and serial numbers here: Model # Serial # Find these numbers on a label inside the refrigerator compartment at the top on the right.
25
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following: This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used. Also see the How to Connect Electricity section. Do not allow children to climb, stand or hang on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves. Do not touch the cold surfaces in the freezer compartment when hands are damp or wet. Skin may stick to these extremely cold surfaces. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the icemaker. Do not place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in. Installation of the icemaker must be done by a qualified service technician. Keep fingers out of the "pinch point" areas; clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area. Unplug the refrigerator before cleaning and making repairs. NOTE: We strongly recommend that any servicing be performed by a qualified individual. Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a live wire filament. (A burned-out light bulb may break when being replaced.) NOTE: Setting either or both controls to 0 (OFF) does not remove power to the light circuit. Do not refreeze frozen foods which have thawed completely.
26
WARNING!
HOW TO CONNECT ELECTRICITY
The power cord of this appliance is equipped with an earthing plug which mates with a standard earthed wall outlet to minimize the possibility of electric shock hazard from this appliance. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly earthed. Where an unearthed wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly earthed wall outlet. The refrigerator should always be plugged into Make sure proper earthing exists its own individual elecbefore using. trical outlet. This provides the best performance and also prevents overloading Earthing house wiring circuits plug which could cause a fire hazard from overheated wires. Please refer to the rating plate on the refrigerator for the correct voltage, wattage and frequency. If the product plug does not fit your outlet, the product should be fitted with a new plug. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. IMPORTANT: The refitting of electric plugs and cables should be done by a qualified technician or service agent. In some countries the refitting of electric plugs and cables is only permitted when the work is completed by a qualified technician. If the power supply cord becomes damaged, it must be replaced by a qualified service agent in order to avoid a safety hazard. Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.
27
The temperature controls are preset in the factory at 5 for both the refrigerator and freezer compartments. To adjust the set point temperature, press the "+" (warmer) or "-" (colder) button on either the Freezer or Refrigerator side. The set point light will come on. Press "+" or "-" until the desired setting is reached. Several adjustments may be required. Each time you adjust controls, allow 24 hours after each adjustment for the refrigerator to reach the setting you have selected. Setting either or both controls to 0 stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator. Control settings will vary based on personal preferences, usage and operating conditions and may require more than one adjustment. NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now.
NOTE: Internal temperature may be affected by such factors as the location of the refrigerator, ambient temperature and frequency of door openings. Adjust temperature controls as required to compensate for these factors.
28
Place the top of the cartridge up inside the cartridge holder and slowly turn it to the right.
When the door is only partially open it will automatically close. Beyond this stop the door will stay open.
29
30
Freezer Baskets
To remove, slide out to the stop position, lift the front past the stop position and slide out. Make sure you push the baskets all the way back in before you close the door. WARNING: Poor performance may occur if freezer baskets are not used. Storage of items in the freezer without using baskets may result in poor temperature performance due to restrictions of air flow within the freezer compartment.
To remove this type of shelf: 1. Lift up the left side of the shelf and slide it left into the center of the shelf supports. 2. Rotate the right side of the shelf up and out of the shelf supports.
31
Freezer Performance
This Refrigerator/Freezer has an overall "Four Star" rating.
Freezer performance is classified by star ratings defined by ISO 8561 STANDARD AND SUMMARY BELOW: FREEZINGLOAD TEMP. (FOOD TEMPERATURE) Below 6C. Below 12C. or Below 18C.
CODE
32
Crisper Removal
The top crispers can easily be removed by pulling the drawer straight out and lifting the drawer up and over the stop location. If the door prevents you from taking out the drawers, first try to remove the door bins. If this does not offer enough clearance, the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out. To remove the bottom crisper: 1. Pull the drawer out to the stop position. 2. Rotate all four swing locks to the unlock position. 3. Lift the front of the drawer up and out. To replace the bottom crisper: 1. Make sure all four swing locks are in the unlock position. 2. Place the sides of the drawer into the drawer supports, making sure the swing locks fit on the drawer slots. 3. Lock all four swing locks by rotating them to the lock position.
33
Automatic Icemaker
The icemaker will produce seven cubes per cycle approximately 100130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions. To access the icemaker: Pull the shelf above the ice drawer straight out. Always be sure to replace the shelf. If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the O position. When the refrigerator has been connected to the water supply, set the power switch to the l position. You will hear a buzzing sound each time the icemaker fills with water. The icemaker will fill with water when it cools to 10C. A newly-installed refrigerator may take 12 to 24 hours to begin making ice cubes. Throw away the first few batches of ice to allow the water line to clear.
Pull the upper freezer shelf straight out to access the icemaker. Always be sure to replace the shelf. The shelf can be used for storage.
1. Lift the bin, then pull it forward until the bin stops.
2. Lower the bin to access ice or reach the power switch. NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.
Be sure nothing interferes with the sweep of the feeler arm. When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together. If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink. If ice cubes get stuck in the icemaker, the green power light will blink. To correct this, set the power switch to O and remove the cubes. Set the power switch to I to restart the icemaker. After the icemaker has been turned on again, there will be a delay of about 45 minutes before the icemaker resumes operation. NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.
34
Dispenser Light
The LIGHT pad turns the night light in the dispenser on and off. The light also comes on when the dispenser cradle is pressed. On some models, if this light burns out, it should be replaced with a 6 watt 12 V maximum bulb.
Door Alarm
Use Door Alarm to sound if either door is open for more than 3 minutes. The alarm will stop once the door is closed. For LCD models, a popup screen will appear. The alarm can be silenced by touching the LCD screen.
Spill Shelf
35
Preparing to Move
Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage. When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator. Be sure the refrigerator stays in an upright position during moving.
36
Freezer Compartment
1. Unplug the refrigerator. 2. Remove the shelf just above the light shield. (The shelf will be easier to remove if it is emptied first.) On some models, a screw at the top of the light shield will need to be removed. 3. To remove the light shield, press in on the sides, and lift up and out. 4. Replace the bulb with an appliance bulb of the same or lower wattage, and reinstall the light shield. When reinstalling the light shield, make sure the top tabs snap securely into place. Replace the screw (on some models). 5. Reinstall the shelf and plug the refrigerator back in.
Dispenser
1. Unplug the refrigerator. 2. The bulb is located on the dispenser under the control panel. Remove the light bulb by turning it counterclockwise. 3. Replace the bulb with a bulb of the same size and wattage. 4. Plug the refrigerator back in.
37
Installation Instructions
BEFORE YOU BEGIN
Read these instructions completely and carefully. IMPORTANT inspectors use. IMPORTANT nances. Note to Installer the Consumer.
Refrigerator
Models 21, 23, 25, 27 & 29
CLEARANCES
Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections: Sides Top Back 4 mm 25 mm 13 mm
Save these instructions for local Observe all governing codes and ordi Be sure to leave these instructions with Keep these instructions for future
DIMENSIONS
A* B C** D E F G 1733 mm 908 mm 738 mm 1156 mm 1214 mm 986 mm 1355 mm 994 mm
Skill level Installation of this appliance requires basic mechanical skills. Completion time Refrigerator Installation 15 minutes. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Warranty.
F A
REFRIGERATOR LOCATION
Do not install the refrigerator where the temperature will go below 16C because it will not run often enough to maintain proper temperatures. Do not install the refrigerator where the temperature will go above 43C because it will not perform properly. Install it on a floor strong enough to support it fully loaded. B H D
38
Installation Instructions
ROLLERS
The rollers have 3 purposes: Rollers adjust so the door closes easily when opened about halfway. [Raise the front about 5/8" (16 mm) from the floor.] Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble. Rollers allow you to move the refrigerator away from the wall for cleaning. Final leveling adjustments should be made after the refrigerator has been installed. To adjust the rollers: 1. Remove the base grille by opening the doors, removing the screws at each end, and pulling it straight out. 2. Turn the front roller adjusting screws clockwise to raise the refrigerator, counterclockwise to lower it. Use a 3/8" hex socket or wrench, or an adjustable wrench. 3. These models also have rear adjustable rollers so you can align the refrigerator with your kitchen cabinets. Use a long-handled 5/16" socket wrench to turn the screws for the rear rollersclockwise to raise the refrigerator, counterclockwise to lower it. 4. Replace the base grille.
DOOR ALIGNMENT
After leveling, make sure that the refrigerator door is 1/16" higher than the freezer door. To align the doors, adjust the refrigerator door. 1. Using a 7/16" socket wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it. (A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.) 2. After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.
39
Installation Instructions
DIMENSIONS AND SPECIFICATIONS
40
Installation Instructions
BEFORE YOU BEGIN
Follow these recommendations carefully to minimize the risk of expensive water damage. Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator. If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position. Do not install the icemaker tubing in areas where temperatures fall below freezing. When using any electrical device (such as a power drill) during installation, be sure the device is insulated or wired in a manner to prevent the hazard of electric shock. All installations must be in accordance with local plumbing code requirements. Installation of the icemaker must be done by a qualified service technician. On models using the refrigeration connection at the water valve, remove the plastic flexible cap.
Insert the end of the tubing into the water valve connection as far as possible. While holding the tubing, tighten the fitting. Fasten the tubing into the clamp provided to hold it in a vertical position. You may need to pry open the clamp. One of the illustrations below will look like the connection on your icemaker.
41
Installation Instructions
2. TURN THE WATER ON AND PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall.
NOTE: In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.
42
The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a high-pitched hum or pulsating sound while it is operating. You may hear a whooshing sound when the doors close. This is due to pressure equalizing within the refrigerator.
You may hear the fans spinning at high speeds. This happens when the refrigerator is first plugged in, when the doors are opened frequently or when a large amount of food is added to the refrigerator or freezer compartments. The fans are helping to maintain the correct temperatures. If either door is open for over 3 minutes, you may hear the fans come on in order to cool the light bulbs. The fans change speeds in order to provide optimal cooling and energy savings.
WATER SOUNDS
The flow of refrigerant through the freezer cooling coils may make a gurgling noise like boiling water. Water dropping on the defrost heater can cause a sizzling, popping or buzzing sound during the defrost cycle. A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan. Closing the door may cause a gurgling sound due to pressure equalization.
For additional information on normal icemaker and dispenser operating sounds, see the About the automatic icemaker and About the ice and water dispenser sections.
43
Possible Causes
Refrigerator in defrost cycle. Either or both controls set to 0 (off). Refrigerator is unplugged. The fuse is blown/circuit breaker is tripped. The refrigerator is in showroom mode.
What To Do
Wait about 30 minutes for defrost cycle to end. Set the controls to a temperature setting. Push the plug completely into the outlet. Replace fuse or reset the breaker. Unplug the refrigerator and plug it back in. See Rollers. Wait 24 hours for the refrigerator to completely cool down. This is normal. Check to see if package is holding door open. This is normal. See About the controls.
Vibration or rattling (slight vibration is normal) Motor operates for long periods or cycle on and off frequently. (Modern refrigerators with more storage space and a larger freezer require more operating time. They start and stop often to maintain even temperatures).
Rollers need adjusting. Normal when refrigerator is first plugged in. Often occurs when large amounts of food are placed in refrigerator. Door left open. Hot weather or frequent door openings. Temperature controls set at the coldest setting.
Temperature control not set cold enough. Warm weather or frequent door openings. Door left open.
Set the temperature control one step colder. See About the controls. Check to see if package is holding door open.
Frost or ice crystals on frozen food (frost within package is normal) Divider between refrigerator and freezer compartments feels warm
Door left open. Too frequent or too long door openings. Automatic energy saver system circulates warm liquid around front edge of freezer compartment. Icemaker power switch is in the off position. Water supply turned off or not connected. Freezer compartment too warm.
Wait 24 hours for the refrigerator to completely cool down. Level cubes by hand.
Piled up cubes in the storage bin cause the icemaker to shut off. Ice cubes stuck in icemaker. (Green power light on icemaker blinking).
Turn off the icemaker, remove cubes and turn the icemaker back on.
44
Possible Causes
Icemaker power switch is in the on position, but the water supply to the refrigerator has not been connected. Ice storage bin needs cleaning. Food transmitting odor/taste to ice cubes. Interior of refrigerator needs cleaning.
What To Do
Set the power switch to the off position. Keeping it in the on position will damage the water valve. Empty and wash bin. Discard old cubes. Wrap foods well. See Care and cleaning. Replace filter cartridge with new cartridge or with plug. Check to see if package is holding door open. See About the controls. Turn on icemaker or water supply.
Water filter clogged. Door left open. Temperature control not set cold enough.
Icemaker turned off or water supply turned off. Ice cubes are frozen to icemaker feeler arm. Irregular ice clumps in storage container.
Remove cubes. Break up with fingertip pressure and discard remaining clumps. Freezer may be too warm. Adjust the freezer control to a colder setting, one position at a time, until clumps do not form. Press and hold the LOCK CONTROL pad for 3 seconds. Dispense water until all water in system is replenished.
Dispenser is LOCKED. Water has poor taste/odor Water dispenser has not been used for a long time. Normal when refrigerator is first installed. Water dispenser has not been used for a long time. Water system has been drained. Water dispenser does not work Water supply line turned off or not connected. Water filter clogged. Air may be trapped in the water system. Dispenser is LOCKED. Water spurting from dispenser Newly-installed filter cartridge.
Wait 24 hours for the refrigerator to completely cool down. Dispense water until all water in system is replenished.
Allow several hours for replenished supply to chill. See Installing the water line. Replace filter cartridge or remove filter and install plug. Press the dispenser arm for at least two minutes. Press and hold the LOCK CONTROL pad for 3 seconds. Run water from the dispenser for 3 minutes (about six liters). Call for service. Set to a warmer setting. Call a plumber. Replace filter cartridge or remove filter and install plug. Press and hold the LOCK CONTROL pad for 3 seconds.
Water is not dispensed but icemaker is working No water or ice cube production
Water in reservoir is frozen. Refrigerator control setting is too cold. Supply line or shutoff valve is clogged. Water filter clogged. Dispenser is LOCKED.
45
Problem
CUBED ICE was selected but CRUSHED ICE was dispensed Orange glow in the freezer Refrigerator has odor
Possible Causes
Last setting was CRUSHED ICE. Defrost heater is on. Foods transmitting odor to refrigerator.
What To Do
A few cubes were left in the crusher from the previous setting. This is normal. This is normal. Foods with strong odors should be tightly wrapped. Keep an open box of baking soda in the refrigerator; replace every three months. See Care and cleaning. Apply paraffin wax to the face of the gasket. Move the door bin up one position. Wipe surface dry.
Interior needs cleaning. Door not closing properly Door gasket on hinge side sticking or folding over. A door bin is hitting a shelf inside the refrigerator. Moisture forms on outside of refrigerator Moisture collects inside (in humid weather, air carries moisture into refrigerator when doors are opened) Interior light does not work Not unusual during periods of high humidity. Too frequent or too long door openings.
Replace fuse or reset the breaker. See Replacing the light bulbs. Poke ice through with a wooden spoon.
Water on kitchen floor or on bottom of freezer Hot air from bottom of refrigerator
Normal air flow cooling motor. In the refrigeration process, it is normal that heat be expelled in the area under the refrigerator. Some floor coverings are sensitive and will discolor at these normal and safe temperatures. Adaptive defrost keeps compressor running during door openings. Door open. Packaging. Wrong weight selected. Item with high fat content. Not using Chill/Thaw tray. This is normal. The refrigerator will cycle off after the door remains closed for 2 hours. Close door. Increase time or re-package in plastic. Select a larger weight. Select a larger weight. Place items on tray and allow space in between items for better air flow. Allow 24 hours for system to stabilize. Allow 24 hours for system to stabilize. Allow 24 hours for system to stabilize. Allow 24 hours for system to stabilize. This is normal. In order to minimize energy usage, the Select Temp feature is disabled when the refrigerator temperature control is set at the warmest setting.
Refrigerator never shuts off but the temperatures are OK Refrigerator beeping Food isnt thawing/chilling
Unit just plugged in. Door open for too long. Warm food added to refrigerator. Defrost cycle is in process.
46
47
48