Escolar Documentos
Profissional Documentos
Cultura Documentos
For Parts and Service, contact our authorized distributor: call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
I. GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade. Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. Never carry passengers. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either the entire grass catcher or the guard in place. Slow down before turning. Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove keys before dismounting. Turn off blades when not mowing. Stop engine before removing grass catcher or unclogging chute. Mow only in daylight or good artificial light. Do not operate the machine while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways. Use extra care when loading or unloading the machine into a trailer or truck. Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mowerrelated injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury. II. SLOPE OPERATION
Slopes are a major factor related to loss-of-control and tipover accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
DO: Mow up and down slopes, not across. Remove obstacles such as rocks, tree limbs, etc. Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. Follow the manufacturers recommendations for wheel weights or counterweights to improve stability. Use extra care with grass catchers or other attachments. These can change the stability of the machine.
Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope.
DO NOT: Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. Do not mow on wet grass. Reduced traction could cause sliding. Do not try to stabilize the machine by putting your foot on the ground. Do not use grass catcher on steep slopes. III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. Keep children out of the mowing area and under the watchful care of another responsible adult. Be alert and turn machine off if children enter the area. Before and when backing, look behind and down for small children. Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. Never allow children to operate the machine. Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision. IV. SERVICE Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. - Use only an approved container. - Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not smoke. - Never refuel the machine indoors. - Never store the machine or fuel container inside where there is an open flame, such as a water heater. Never run a machine inside a closed area. Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition. Never tamper with safety devices. Check their proper operation regularly. Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing. Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. Never make adjustments or repairs with the engine running. Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when necessary. Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. Check brake operation frequently. Adjust and service as required.
SAFETY RULES
Safe Operation Practices for Ride-On Mowers
Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. Never carry passengers or children even with the blades off. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Never carry children. They may fall off and be seriously injured or interfere with safe machine operation. Keep children out of the mowing area and under the watchful care of another responsible adult. Be alert and turn machine off if children enter the area. Before and when backing, look behind and down for small children. Mow up and down slopes (15 Max), not across. Remove obstacles such as rocks, tree limbs, etc. Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles. Use slow speed. Choose a low gear so that you will not have to stop or shift while on the slope. Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly straight down the slope. If machine stops while going uphill, disengage blades, shift into reverse and back down slowly. Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
Look for this symbol to point out important safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. CAUTION: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. CAUTION: Do not coast down a hill in neutral, you may lose control of the tractor. CAUTION: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Operate only at the lowest possible speed when on a slope. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.
WARNING
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
WARNING
Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
TABLE OF CONTENTS
SAFETY RULES ........................................................ 2-3 PRODUCT SPECIFICATIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ...................... 4, 15-18 ASSEMBLY ................................................................ 6-8 OPERATION ............................................................. 9-14 MAINTENANCE SCHEDULE ....................................... 15 SERVICE AND ADJUSTMENTS ............................. 19-23 STORAGE ................................................................... 24 TROUBLESHOOTING ............................................. 25-26 REPAIR PARTS - TRACTOR .................................. 28-43
PRODUCT SPECIFICATIONS
GASOLINE CAPACITY AND TYPE: OIL TYPE (API-SF-SJ): OIL CAPACITY: SPARK PLUG: (GAP: .030") GROUND SPEED (MPH): TIRE PRESSURE: CHARGING SYSTEM: BATTERY: 1.25 GALLONS UNLEADED REGULAR SAE 30 (above 32F) SAE 5W-30 (below 32F) 3.4 PINTS CHAMPION RN4C FORWARD: REVERSE: FRONT: REAR: 5.2 2.7 14 PSI 12 PSI
CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/department. We have competent, well-trained technicians and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly. Always observe the SAFETY RULES.
CUSTOMER RESPONSIBILITIES
Read and observe the safety rules. Follow a regular schedule in maintaining, caring for and using your tractor. Follow the instructions under Customer Responsibilities and Storage sections of this owners manual.
3 AMPS BATTERY 5 AMPS HEADLIGHTS AMP/HR: MIN. CCA: CASE SIZE: 25 190 U1R
WARNING: This tractor is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engines exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. A spark arrester for the muffler is available through your nearest authorized service center/department (See REPAIR PARTS section of this manual).
UNASSEMBLED PARTS
Steering Wheel
Steering Wheel Adapter
Seat
(1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Lockwasher 3/8 Steering Wheel Insert (1) Lock Washer 1/2
(1) Bolt
Key
(2) Keys
Slope Sheet
ASSEMBLY
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
INSERT 3/8 HEX BOLT 3/8 LOCK WASHER LARGE FLAT WASHER
TABS
ADAPTER
FIG. 1
TERMINAL
FIG. 2
ASSEMBLY
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment bolt. Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan. Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor. Pivot seat and pan forward and assemble adjustment bolt, lockwasher and flat washer loosely. Do not tighten Lower seat into operating position and sit on seat. Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down. Get off seat without moving its adjusted position. Raise seat and tighten adjustment bolt securely.
TO ROLL TRACTOR OFF SKID (See Operation section, page 10, for location and function of controls)
Press lift lever plunger and raise attachment lift lever to its highest position. Release parking brake by depressing clutch/brake pedal. Place freewheel control in freewheeling position to disengage transmission (See TO TRANSPORT in the Operation section of this manual). Roll tractor forward off skid. Remove banding holding deflector shield up against tractor.
TO DRIVE TRACTOR OFF SKID (See Operation section, page 10, for location and function of controls)
WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects. Be sure all the above assembly steps have been completed. Check engine oil level and fill fuel tank with gasoline. Place freewheel control in "transmission engaged" position. Sit on seat in operating position, depress clutch/brake pedal and set the parking brake. Place motion control lever in neutral (N) position. Press lift lever plunger and raise attachment lift lever to its highest position. Start the engine. After engine has started, move throttle control to idle position. Release parking brake. Slowly move the motion control lever forward and slowly drive tractor off skid. Apply brake to stop tractor, set parking brake and place motion control lever in neutral position. Turn ignition key to "OFF" position. Continue with the instructions that follow.
SEAT
SEAT PAN
SHOULDER BOLT
ADJUSTMENT BOLT
FIG. 3 NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.
ASSEMBLY
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. Reduce tire pressure to PSI shown in PRODUCT SPECIFICATIONS section of this manual.
3CHECKLIST
BEFORE YOU OPERATE AND ENJOY YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: All assembly instructions have been completed. No remaining loose parts in carton. Battery is properly prepared and charged. (Minimum 1 hour at 6 amps). Seat is adjusted comfortably and tightened securely. All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory). Be sure mower deck is properly leveled side-to-side/ front-to-rear for best cutting results. (Tires must be properly inflated for leveling). Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers. Check wiring. See that all connections are still secure and wires are properly clamped. Before driving tractor, be sure freewheel control is in drive position. WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS: Engine oil is at proper level. Fuel tank is filled with fresh, clean, regular unleaded gasoline. Become familiar with all controls - their location and function. Operate them before you start the engine. Be sure brake system is in safe operating condition. It is important to purge the transmission before operating your tractor for the first time. Follow proper starting and transmission purging instructions (See TO START ENGINE and PURGE TRANSMISSION in the Operation section of this manual).
OPERATION
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
BATTERY
CAUTION OR WARNING
REVERSE
FORWARD
FAST
SLOW
ENGINE ON
ENGINE OFF
OIL PRESSURE
LIGHTS ON
FUEL
CHOKE
MOWER HEIGHT
UNLOCKED
MOWER LIFT
P
ATTACHMENT CLUTCH ENGAGED REVERSE NEUTRAL HIGH LOW PARKING BRAKE
15
15
15
IGNITION
SLOPE HAZARDS
OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
ATTACHMENT CLUTCH LEVER
IGNITION SWITCH
THROTTLE/CHOKE CONTROL
CLUTCH/BRAKE PEDAL
FIG. 4
Our tractors conform to the safety standards of the American National Standards Institute. ATTACHMENT CLUTCH LEVER: Used to engage the mower blades, or other attachments mounted to your tractor. LIGHT SWITCH: Turns the headlights on and off. THROTTLE/CHOKE CONTROL: Used for starting and controling engine speed. CLUTCH/BRAKE PEDAL: Used for declutching and braking the tractor and starting the engine. PARKING BRAKE: Locks clutch/brake pedal into the brake position. FREEWHEEL CONTROL: Disengages transmission for pushing or slowly towing the tractor with the engine off. MOTION CONTROL LEVER: Selects the speed and direction of tractor. ATTACHMENT LIFT LEVER: Used to raise and lower the mower deck or other attachments mounted to your tractor. LIFT LEVER PLUNGER: Used to release attachment lift lever when changing its position. IGNITION SWITCH: Used for starting and stopping the engine.
10
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD).
NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause browning of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas. CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty grass catcher, etc.
Always operate engine at full throttle. Operating engine at less than full throttle reduces the battery charging rate. Full throttle offers the best bagging and mower performance.
"BRAKE" POSITION
MOTION CONTROL LEVER CLUTCH/BRAKE PEDAL "DRIVE" POSITION PARKING BRAKE "DISENGAGED" POSITION
FIG. 5
ENGINE Move throttle control to slow position. NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to backfire. Turn ignition key to OFF position and remove key. Always remove key when leaving tractor to prevent unauthorized use. Never use choke to stop engine.
11
OPERATION
TO ADJUST GAUGE WHEELS (See Fig. 6)
Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. Adjust gauge wheels with tractor on a flat level surface. Adjust mower to desired cutting height (See TO ADJUST MOWER CUTTING HEIGHT in the Operation section of this manual). With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely. Repeat for opposite side installing gauge wheel in same adjustment hole.
GAUGE WHEEL MOUNTING BRACKET
TO OPERATE ON HILLS
CAUTION: Do not drive up or down hills with slopes greater than 15 and do not drive across any slope. Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills. If slowing is necessary, move throttle control lever to slower position. If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake. Move motion control lever to neutral (N) position.
IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.
To restart movement, slowly release parking brake and clutch/brake pedal. Slowly move motion control lever to slowest setting. Make all turns slowly.
FIG. 6
FIG. 8
FIG. 7
12
OPERATION
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped, from the factory, already filled with summer weight oil. Check engine oil with tractor on level ground. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until FULL mark on dipstick is reached. Do not overfill. For cold weather operation you should change oil for easier starting (See OIL VISCOSITY CHART in the Customer Responsibilities section of this manual). To change engine oil, see the Customer Responsibilities section in this manual. Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. Insert key into ignition and turn key clockwise to START position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.
ADD GASOLINE
WARM WEATHER STARTING (50 F and above) When engine starts, move the throttle control to the fast position. The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above. COLD WEATHER STARTING ( 50 F and below) When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature. AUTOMATIC TRANSMISSION WARM UP Before driving the unit in cold weather, the transmission should be warmed up as follows: Be sure the tractor is on level ground. Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position. Allow one minute for transmission to warm up. This can be done during the engine warm up period. The attachments can also be used during the engine warm-up period after the transmission has been warmed up. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See TO ADJUST CARBURETOR in the Service and Adjustments section of this manual.
IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32F(0C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.
WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.
PURGE TRANSMISSION
CAUTION: Never engage or disengage freewheel lever while the engine is running. To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.
Place tractor safely on level surface with engine off and parking brake set. Disengage transmission by placing freewheel control in freewheeling position (See TO TRANSPORT in this section of manual).
13
OPERATION
Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal. Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times. NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system. Move motion control lever to neutral (N) position. Shutoff engine and set parking brake. Engage transmission by placing freewheel control in driving position (See TO TRANSPORT in this section of manual). Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal. Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times. Your tractor is now purged and now ready for normal operation.
MOWING TIPS
Mower should be properly leveled for best mowing performance. See TO LEVEL MOWER HOUSING in the Service and Adjustments section of this manual. The left hand side of mower should be used for trimming. Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting. When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 9). If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height. Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing. Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired. When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.
FIG. 9
14
CUSTOMER RESPONSIBILITIES
MAINTENANCE SCHEDULE
FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation Check Tire Pressure Check Operator Presence and Interlock Systems Check for Loose Fasteners Sharpen/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Check Transaxle Cooling Adjust Blade Belt(s) Tension Adjust Motion Drive Belt(s) Tension Check Engine Oil Level Change Engine Oil
1,2,3 2 2 5 5 6 4 7
DATES
T R A C T 0 R
E N G I N E
Clean Air Filter Clean Air Screen Inspect Muffler/Spark Arrester Replace Oil Filter (If equipped) Clean Engine Cooling Fins Replace Spark Plug Replace Air Filter Paper Cartridge Replace Fuel Filter
1, 2 2
1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. 3 - If equipped with oil filter, change oil every 50 hours. 4 - Replace blades more often when mowing in sandy soil.
5 - If equipped with adjustable system. 6 - Not required if equipped with maintenance-free battery. 7 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum. Do not overtighten.
GENERAL RECOMMENDATIONS
The warranty on this tractor does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain tractor as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tractor. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. Once a year you should replace the spark plug, clean or replace air filter, and check blades and belts for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer.
SPINDLE
ZERK
LUBRICATION CHART
SPINDLE
ZERK BEARING ZERK
FRONT WHEEL
BEARING ZERK
15
CUSTOMER RESPONSIBILITIES
TRACTOR
Always observe safety rules when performing any maintenance.
TRAILING EDGE UP BLADE CENTER HOLE LOCK WASHER MANDREL ASSEMBLY
BRAKE OPERATION
If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See TO ADJUST BRAKE in the Service and Adjustments section of this manual).
TIRES
Maintain proper air pressure in all tires (See PRODUCT SPECIFICATIONS section of this manual). Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.
STAR
*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.
FIG. 10
BLADE CARE
For best results mower blades must be kept sharp. Replace bent or damaged blades.
5/8" BOLT OR PIN BLADE
FIG. 11
BATTERY
Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. Keep battery and terminals clean. Keep battery bolts tight. Keep small vent holes open. Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.
Reassemble hex bolt, lock washer and flat washer in exact order as shown. Tighten bolt securely (27-35 Ft. Lbs. torque).
16
CUSTOMER RESPONSIBILITIES
TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to leak power. Open battery box door. Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. Rinse the battery with plain water and dry. Clean terminals and battery cable ends with wire brush until bright. Coat terminals with grease or petroleum jelly. Reinstall battery (See REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level. TO CHANGE ENGINE OIL (See Figs. 12 and 13) Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ. Be sure tractor is on level surface. Oil will drain more freely when warm. Catch oil in a suitable container. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. Remove cap from bottom fitting of drain valve and install the drain tube onto the fitting. Unlock drain valve by pushing inward and turning counterclockwise. To open, pull out on the drain valve. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see PRODUCT SPECIFICATIONS section of this manual. Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at FULL line on dipstick.
OIL DRAIN VALVE
V-BELTS
Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.
TRANSAXLE COOLING
The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. Inspect cooling fan to be sure fan blades are intact and clean. Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins.
ENGINE
LUBRICATION
Only use high quality detergent oil rated with API service classification SF-SJ. Select the oils SAE viscosity grade according to your expected operating temperature.
SAE VISCOSITY GRADES SAE 30 5W-30 F C
-20 -30 -20 0 -10 30 32 40 0 10 60 20 80 30 100 40
CAP
DRAIN TUBE
FIG. 13
FIG. 12
17
CUSTOMER RESPONSIBILITIES
AIR FILTER
Your engine will not run properly using a dirty air filter. Remove cartridge every 25 hours of operation and tap to clean. Replace paper cartridge once a year or after every 100 hours of operation, more often if used in very dusty, dirty conditions. Remove knobs and cover. Remove foam pre-cleaner element by sliding it off of the paper cartridge. NOTE: Do not attempt to clean or oil the paper cartridge. Replace paper cartridge once a year or after every 100 hours of operation; more often if used in very dusty or dirty conditions. Wash foam pre-cleaner in liquid detergent and water. Wrap foam pre-cleaner in cloth and squeeze dry. Lightly coat foam pre-cleaner with clean engine oil. Squeeze in towel to remove excess oil. Do not saturate. Install foam pre-cleaner over paper cartridge. Reassemble cover and tighten knobs securely.
MUFFLER
Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage.
SPARK PLUGS
Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in PRODUCT SPECIFICATIONS section of this manual.
FUEL FILTER
FIG. 15
CLEANING
Clean engine, battery, seat, finish, etc. of all foreign matter. Keep finished surfaces and wheels free of all gasoline, oil, etc. Protect painted surfaces with automotive type wax. We do not recommend using a garden hose to clean your tractor unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in a shortened engine life.
FIG. 14
18
TRACTOR
TO REMOVE MOWER (See Fig. 16)
Mower will be easier to remove from the right side of tractor. Place attachment clutch in DISENGAGED position. Move attachment lift lever forward to lower mower to its lowest position. Roll belt off engine pulley. Remove small retainer spring, and lift clutch spring off pulley bolt. Remove large retainer spring, slide collar off and push housing guide out of bracket. Disconnect anti-swaybar from chassis bracket by removing retainer spring. Disconnect suspension arms from rear deck brackets by removing retainer springs. Disconnect front links from deck by removing retainer springs. Raise lift lever to raise suspension arms. Slide mower out from under tractor. IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME.
GROUND LINE
FIG. 17
SQUARE HOLE
HOUSING GUIDE
BRACKET
FIG. 16
19
NUT "E"
FIG. 20
To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position. Check adjustment on right side of tractor. Measure distance D directly in front and behind the mandrel at bottom edge of mower housing as shown. Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8". If links are not equal in length, adjust one link to same length as other link. To lower front of mower loosen nut E on both front links an equal number of turns. When distance D is 1/8" to 1/2" lower at front than rear, tighten nuts F against trunnion on both front links. To raise front of mower, loosen nut F from trunnion on both front links. Tighten nut E on both front links an equal number of turns. When distance D is 1/8" to 1/2" lower at front than rear, tighten nut F against trunnion on both front links. Recheck side-to-side adjustment.
MANDREL
MANDREL PULLEY
FIG. 21
"D" "D"
FIG. 19
20
NUT A
JAM NUT
OPERATING ARM DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/DEPARTMENT
FIG. 22
ADJUSTMENT BOLT
FIG. 24
TRANSMISSION REMOVAL/REPLACEMENT
Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See PURGE TRANSMISSION in the Operation section of this manual.
If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the Assembly section of this manual.
21
CHASSIS
FIG. 26
FIG. 25
TO ATTACH JUMPER CABLES Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis. Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery. Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery. TO REMOVE CABLES, REVERSE ORDER BLACK cable first from chassis and then from the fully charged battery. RED cable last from both batteries.
FIG. 27
22
ENGINE
HEX BOLT
FIG. 28
THROTTLE CABLE
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.
CLAMP SCREW
HOLE A
FIG. 30
HEADLIGHT WIRE CONNECTOR
TO ADJUST CARBURETOR
The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual. High speed stop is factory adjusted. Do not adjust - damage may result.
FIG. 29
IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.
23
STORAGE
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.
ENGINE
FUEL SYSTEM
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.
TRACTOR
Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. Clean entire tractor (See CLEANING in the Customer Responsibilities section of this manual). Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual). Lubricate as shown in the Customer Responsibilities section of this manual. Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. Touch up all rusted or chipped paint surfaces; sand lightly before painting.
Drain the fuel tank. Start the engine and let it run until the fuel lines and carburetor are empty. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. Use fresh fuel next season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See ENGINE in the Customer Responsibilities section of this manual).
BATTERY
Fully charge the battery for storage. After a period of time in storage, battery may require recharging. To help prevent corrosion and power leakage during long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see TO CLEAN BATTERY AND TERMINALS in the Customer Responsibilities section of this manual). After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals. If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.
CYLINDER(S)
Remove spark plug(s). Pour one ounce of oil through spark plug hole(s) into cylinder(s). Turn ignition key to START position for a few seconds to distribute oil. Replace with new spark plug(s).
OTHER
Do not store gasoline from one season to another. Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. If possible, store your tractor indoors and cover it to give protection from dust and dirt. Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.
24
TROUBLESHOOTING POINTS
PROBLEM
Will not start
CAUSE
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Out of fuel. Engine not CHOKED properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. Loose or damaged wiring. Carburetor out of adjustment. Engine valves out of adjustment. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
CORRECTION
Fill fuel tank. See TO START ENGINE in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Drain fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. Check all wiring. See To Adjust Carburetor in Service Adjustments section. Contact an authorized service center/department.
Hard to start
1. 2. 3. 4. 5. 6. 7. 8.
Dirty air filter. Bad spark plug. Weak or dead battery. Dirty fuel filter. Stale or dirty fuel. Loose or damaged wiring. Carburetor out of adjustment. Engine valves out of adjustment.
1. 2. 3. 4. 5. 6. 7. 8.
Clean/replace air filter. Replace spark plug. Recharge or replace battery. Replace fuel filter. Drain fuel tank and refill with fresh gasoline. Check all wiring. See To Adjust Carburetor in Service Adjustments section. Contact an authorized service center/department.
1. 2. 3. 4. 5. 6. 7. 8. 9.
Clutch/brake pedal not depressed. Attachment clutch is engaged. Weak or dead battery. Blown fuse. Corroded battery terminals. Loose or damaged wiring. Faulty ignition switch. Faulty solenoid or starter. Faulty operator presence switch(es).
1. 2. 3. 4. 5. 6. 7. 8. 9.
Depress clutch/brake pedal. Disengage attachment clutch. Recharge or replace battery. Replace fuse. Clean battery terminals. Check all wiring. Check/replace ignition switch. Check/replace solenoid or starter. Contact an authorized service center/department.
1. 2. 3. 4.
Weak or dead battery. Corroded battery terminals. Loose or damaged wiring. Faulty solenoid or starter.
1. 2. 3. 4.
Recharge or replace battery. Clean battery terminals. Check all wiring. Check/replace solenoid or starter.
Loss of power
Cutting too much grass/too fast. Throttle in CHOKE position. Build-up of grass, leaves and trash under mower. Dirty air filter. Low oil level/dirty oil. Faulty spark plug. Dirty fuel filter. Stale or dirty fuel. Water in fuel. Spark plug wire loose. Dirty engine air screen/fins. Dirty/clogged muffler. Loose or damaged wiring. Carburetor out of adjustment. Engine valves out of adjustment.
Set in Higher Cut position/reduce speed. Adjust throttle control. Clean underside of mower housing. Clean/replace air filter. Check oil level/change oil. Clean and regap or change spark plug. Replace fuel filter. Drain fuel tank and refill with fresh gasoline. Drain fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. Connect and tighten spark plug wire. Clean engine air screen/fins. Clean/replace muffler. Check all wiring. See To Adjust Carburetor in Service Adjustments section. Contact an authorized service center/department.
Excessive vibration
1. 2. 3.
1. 2. 3.
Replace blade. Tighten blade bolt. Replace blade mandrel. Tighten loose part(s). Replace damaged parts.
25
TROUBLESHOOTING POINTS
PROBLEM
Engine continues to run when operator leaves seat with attachment clutch engaged
CAUSE
1. Faulty operator-safety presence control system.
CORRECTION
1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
1. 2. 3. 4. 5.
Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, and trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels.
1. 2. 3. 4. 5.
Replace blade. Tighten blade bolt. Level mower deck. Clean underside of mower housing. Replace blade mandrel. Clean around mandrels to open vent holes.
1. 2. 3. 4.
Obstruction in clutch mechanism. Worn/damaged mower drive belt. Frozen idler pulley. Frozen blade mandrel.
1. 2. 3. 4.
Remove obstruction. Replace mower drive belt. Replace idler pulley. Replace blade mandrel.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Engine speed too slow. Travel speed too fast. Wet grass. Mower deck not level. Low/uneven tire air pressure. Worn, bent or loose blade. Buildup of grass, leaves and trash under mower. Mower drive belt worn. Blades improperly installed. Improper blades used. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
Place throttle control in FAST position. Shift to slower speed. Allow grass to dry before mowing. Level mower deck. Check tires for proper air pressure. Replace/sharpen blade. Tighten blade bolt. Clean underside of mower housing. Replace mower drive belt. Reinstall blades sharp edge down. Replace with blades listed in this manual. Clean around mandrels to open vent holes.
1. 2. 3. 4. 5.
Switch is OFF. Bulb(s) burned out. Faulty light switch. Loose or damaged wiring. Blown fuse.
1. 2. 3. 4. 5.
Turn switch ON. Replace bulb(s). Check/replace light switch. Check wiring and connections. Replace fuse.
1. 2. 3. 4.
Bad battery cell(s). Poor cable connections. Faulty regulator (if so equipped). Faulty alternator.
1. 2. 3. 4.
Loss of drive
1. 2. 3.
Freewheel control in disengaged position. Motion drive belt worn, damaged, or broken. Air trapped in transmission during shipment or servicing. Engine throttle control not set at SLOW position for 30 seconds before stopping engine.
1. 2. 3.
Place freewheel control in engaged position. Replace motion drive belt. Purge transmission.
1.
1.
Move throttle control to SLOW position and allow to idle for 30 seconds before stopping engine.
26
RED
BLACK
BATTERY
A AMMETER (OPTIONAL)
RED
RED
M STARTER
BLACK
FUSE
WHITE
SOLENOID
RED
B G L
BLACK
A1 A2
WHITE
IGNITION SWITCH
BLACK BLACK
BLACK
BLACK
BLACK
BLACK
BLUE
FUEL LINE
IGNITION UNIT
CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM RED LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM
DIODE
ALTERNATOR
NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST. IGNITION SWITCH
POSITION CIRCUIT MAKE NONE A2+L NONE NONE
BROWN
BLACK
HEADLIGHTS
NON-REMOVABLE CONNECTIONS
REMOVABLE CONNECTIONS WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.
27
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
ELECTRICAL
21 22
42 24 41
43 27
27 26 40
27
27
25
16
16
33
30
D. C.
AM PE RE S
52
45
29 28
27
2 1
28
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
ELECTRICAL
KEY NO.
PART NO.
DESCRIPTION
1 144925 Battery 12 Volt 25 Amp 2 74760412 Bolt Hex Hd 1/4-20unc X 3/4 8 156417 Case Battery 16 153664 Switch Interlock Push -In 21 166181 Harness Asm Light W/4152J 22 4152J Bulb Light #1156 24 108423X Cable Battery 6 Ga 16"red 25 146147 Cable Battery 6 Ga w/16 wire,red 26 175158 Fuse 27 73510400 Nut Keps Hex 1/4-20 unc 28 4207J Cable Ground 6 Ga 12" black 29 121305X Switch Plunger Nc Gray 30 175566 Switch Ign 33 140401 Key Ign 40 170217 Harness Ign 41 71110408 Bolt Blk Fin Hex 1/4-20 X 1/2 42 131563 Cover Terminal Red 43 175141 Solenoid 45 121433X Ammeter Rectangular 52 141940 Protection Wire Loop NOTE: All component dimensions give in U.S. inches 1 inch = 25.4 mm.
29
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
CHASSIS AND ENCLOSURES
212
17 30 24 29
18 24 12
28
26 26 31 3 209
25 25 5 5 53 51 52 55 57
207 6 26 3 35 37 33 10 3 145 37 16 1 13
2
3 38
206
35 34 26 208
3
38 3
30
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
CHASSIS AND ENCLOSURES
PART NO. 169831 169061 17060612 155272 155923 155138 168348X012 72140608 155927 145660 172107X010 74180512 73510500 159639X550 126938X 156437 124028X 74780616 19131312 73800600 150407 150209X599 169467X550 136619 105476X550 105475X550 72110606 17490508 169834 73800400 19091416 144697 161464 144696 74780412 156524 170165 17670508 17670608 17000612 156494 5479J
DESCRIPTION Chassis Drawbar Screw 3/8-16 x 3/4 Bumper Hood/Dash Saddle Flat Lt Fender Shift Clip Retainer Slide-On Dash Bolt RdHd Sqnk. 3/8-16 Unc x 1 Panel Asm. Dash Lh Clip Tinnerman Grile P/L Panel Dash Rh Screw Mach Trhd 5/16-18 Unc x 3/4 Nut Keps 5/16-18 Unc Hood Bumper Hood Plate Mtg Battery/Fuel Tank Fr Bushing Snap Nyl Blk Fuel Line Bolt Fin Hex 3/8-16 Unc x 1 Gr. 5 Washer 13/32 x 13/16 x 12 Ga. Nut Lock Hex w/Insert 3/8-16 UNC Grill/Lens Asm Lens Quadra Fender Asm Bracket Fender Footrest Lh Footrest Rh Bolt RdHd Sht. Sqnk. 3/8-16 x 3/4 Screw Thdrol 5/16-18 x 1/2 Tyt Bracket Asm. Pivot Mower Rear Nut Lock Hex W/Ins. 1/4-20 Washer 9/32 x 7/8 x 16 Ga. Bracket Grille LH Screw Hex Wshd 8-18 x 7/8 Bracket, Grille RH Bolt Fin Hex 1/4-20 x .75 Rod Pivot Chassis/Hood Bolt shoulder 5/16-18 Screw Thdrol 5/16-18 x 1/2 Screw Thdrol 3/8-16 x 1/2 Screw Hex Wsh Thdrol 3/8-16 Insert Lens Reflector Plug Btn Blk
31
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
DRIVE
51 51 57
89
63
212 70 69
197
169 198 171 164 161 159 158 162
116
66 59 65 61
83 14 163 168
42 56 41 42 40
50
64
81
27 42 39 49 47
10 21
82 165 156
166
38 35
61
32
30 52
62 36 52 32 34 37
16
120 36 35 53
95 103 205 16 77 24 19 25 26 15 96 26 1 77 74 75 61 71 30 26 61
28 26 29 22 16 84 27 55 200 61 199
75 78
73 76
16
32
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
DRIVE
KEY NO. 1 PART NO. ------KEY NO. 65 66 69 70 71 72 73 74 75 76 77 78 81 82 83 84 89 95 96 103 116 120 150 151 156 158 159 161 162 163 164 165 166 168 169 171 197 198 199 200 202 205 PART NO. 10040700 154778 142432 134683 169183 19132012 169182 137057 121749X 12000001 123583X 121748X 165596 123782X 19171216 169843 169373X428 170201 4497H 73940800 72110610 73900600 165850 19133210 166002 165589 165494 72140406 73680400 74780416 19091010 165623 166880 165492 165581 17490608 169613 169593 169612 72140508 72110612 19171616
DESCRIPTION Transaxle Hydro Gear Model 322-0510 (Order parts from transaxle manufacturer) Rod Shift Fender Adjust LT Pin Cotter 1/8 x 1 CAD Washer Lock Hvy Helical Bolt, Hex FLGHD 5/16-18 Gr. 5 Nut Lock Hex W/Ins 5/16-18 Unc P Nut Lock Hex W/Wsh 3/8-16 Unc Knob, Round 1/2-13 Rod, Brake Hydro Nut Spring, Brake Rod Washer Pin Cotter 1/8 x 3/4 CAD. Rod, Parking Brake Cap, Parking Brake Bracket, Transaxle Bolt Hex Hd 5/16-18 Unc x 3/4 Shaft, Foot Pedal Bearing, Nylon Washer Pin, Roll Pulley, Idler, Flat Bolt Spacer, Split Keeper, Belt Idler Washer 13/32 x 13/16 x 12 Gauge Pulley, Idler, V-Groove Bellcrank Clutch Grd Drv Stl Retainer, Belt Bolt Nut Crownlock 3/8-16 UNC Nut Crownlock 5/16-18 UNC Link, Clutch Spring, Return, Clutch Bolt Fin Hex 3/8-16 UNC x 1-1/4 V-Belt, Ground Drive Keeper, Center Span Screw 3/8-16 x 3/4 Cover, Pedal Pulley, Engine Bolt, Hex
DESCRIPTION Washer Keeper Belt Engine Hydro Screw Keeper Belt Engine Strap Torque Lh Hydro Washer 13/32 x 1-1/4 x 12 Gauge Strap Torque Rh Hydro Spacer, Axle Washer 25/32 x 1-1/4 x 16 Gauge E-Ring Key, Square Washer 25/32 x 1-5/8 x 16 Gauge Shaft Asm Cross Tapered Spring Torsion T/A Washer 17/32 x 3/4 x 16 Ga. Link, Transaxle Hydro Console, Hydro Control Asm Bypass Hydro Retainer Spring 1" Zinc/Cad Nut Hex Jam Toplock 1/2-20 Unf Bolt Rdhd Sq Neck 3/8-16 x 1.25 Nut Lock Flg. 3/8-16 Unc Bushing Bellcrank Grd Drive Washer 13/32 x 2 x 10 Ga. Washer Srrted 5/16 ID x 1.125 Bracket Shift Mount Hub Tapered Flange Shift LT Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5 Nut Crownlock 1/4-20 Unc Bolt Hex Fin 1/4-20 Unc x 1 Gr. 5 Washer 5/8 x .281 x 10 Ga. Bracket Pivot Lever Screw 5/16-18 x 5/8 Bolt Shoulder 5/16-18 x .561 Plate Fastening LT Screw Thdrol 3/8-16 x 1/2 TY-TT Nyliner Snap-In 5/8 Id Washer Nyl 7/8 Id x .105 Bolt Shoulder5/16-18 Unc Bolt Rdhd Sqnk 5/16-18 Unc x 1 Bolt Carr Sh 3/8-16 x 1-1/2 Gr. 5 Washer 17/32 x 1 x 16 Ga.
8 10 14 15 16 19 21 22 24 25 26 27 28 29 30 32 34 35 36 37 38 39 40 41 42 47 48 49 50 51 52 53 55 56 57 59 61 62 63 64
165619 76020416 10040400 74490544 73800500 73800600 106933X 169498 73350600 106888X 19131316 76020412 145204 71673 174973 74760512 155071 120183X 19211616 1572H 131494 74760644 4470J 165838 19131312 127783 154407 123205X 74760624 73680600 73680500 105710X 105709X 74760620 140294 169691 17060612 8883R 140186 71170764
33
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
STEERING ASSEMBLY
38 63 11 39
41
42 37 37 36
62 51
44 54
27
17
18
68
19 46 8 23 22 6 9 2 40 66 7 29 25 9 5 80
85 85
67
67
47
13 65
67
46 8 6 9
47 7
11
79
3
68 29
82
32 11 26
9 5
4 43
15
40
15 29
43 28 10 30
6 8
15
34
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
STEERING ASSEMBLY
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 13 15 17 18 19 22 23 25 26 27 28 29 30 32 36 37 38 39 40 41 42 43 44 46 47 51 54 62 63 65 66 67 68 79 80 82 85
PART NO. 133741X428 154427 169840 169839 6266H 121748X 19272016 12000029 3366R 169832 10040600 136518 145212 156546 57079 160395 165857 165851 154406 126847X 136874 19131416 17060612 76020412 130465 155099 152927 133742X428 19133812 7810H 100711L 145054X428 121749X 153720 121232X 6855M 73800500 74780520 167902 74780616 160367 154404 72140618 169827 19132012 74950612 169835 133835
DESCRIPTION Wheel Steering Axle Asm Front Spindle Asm Lh Spindle Asm Rh Bearing Race Thrust Harden Washer 25/32 X 1 5/8 X 16ga Washer 27/32 X 1 1/4 X 16 Ga Ring Klip #t5304-75 Bearing Col Strg Blk Link Drag Extended Lockwasher Spacer Bearing Axle Front Hex Flange Lock Shaft Asm Strg 5/8 X 15 19 Lt Washer Thrust 515x 750x 033 Support Shaft Screw Hex Wsh Hd Torx Shaft Asm Pittman Bracket Steering Bushing Rod Tie Blk Lt Gear Sector Washer 13/32 X 7/8 X 16ga Screw 3/8-16x3/4 Pin Rod Tie Wire Form 19 75 Mech Bushing Strg 5/8 Id Dash Screw TT #10-32 x 5 x 3/8 Flange Insert Cap Strg Washer 13/32 x 2-3/8 x 12Ga Locknut Center Adaptor Wheel Strg 640/ 635id Boot Dash Steering Washer 25/32 X 1 1/4 X 16 Ga Extension Steering Non-Adjust Cap Spindle Fr Top Blk Fitting Grease Nut Lock Hex W/Ins. Bolt Fin Hex 5/16-18 Unc P Kit Steering Assembly Service Bolt Fin Hex 3/8-16 Unc x Gr. 5 Spacer Brace Axle Bearing Arm Pittman Bolt Rdhd Sq 3/8-16 Unc x 2-3/4 Brace Axle Washer 13/32 x 1-1/4 x 12 Ga Bolt Hex Nylon 3/8-16 x 3/4 Bracket Susp Chassis Front Fastener Christmas Tree
35
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
ENGINE
13 4
62 85 78 16 81 32 44 46 78 38 14
33 31 40 33 37 23 45
29
36
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
ENGINE
KEY NO. 1 2 3 4 13 14 16 23 29 31 32 33 37 38 40 44 45 46 62 78 81 85
PART NO. 170551 17720410 -----137351 149272 148456 11050600 169837 137180 174642 140527 123487X 137040 148315 124028X 17670412 17000612 19091416 10040500 17060620 73510400 123528X
DESCRIPTION Control Throt/Ch Screw Hex Thd Cut 1/4-20x5/8 T Engine Tec, Model OHV165 (Order parts from engine manufacturer) Muffler Tec 13.5/17 Lt Gasket Tube Drain Oil Easy Washer Lock Ext Tooth 3/8 Shield Browning Arrestor Spark Tank Fuel 2.00 Fr Cap Asm Fuel Clamp Hose Blk Line Fuel 20" Plug Drain Oil Easy Bushing Snap Nyl Blk Fuel Line Screw Hexwsh Thdrol 1/4-20x3/4 Screw 5/16-18 x 3/4 Washer 9/32 X 7/8 X 16ga Washer Lock Hvy Hlcl Spr 5/16 Screw 3/8-16x1-1/4 Nut Flange 1/4-20 Starter Nut Bolt Hex Hd Phillips
37
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
SEAT ASSEMBLY
1
8 9
14 10
8 9 7
5 6 22 21
2 24 5 26 16 25 15 23
4 13 17 12 3
KEY NO. 1 2 3 4 5 6 7 8 9 10 12 13
PART NO. 140116 140551 71110616 19131610 145006 73800600 124181X 17000616 19131614 174894 121246X 121248X
DESCRIPTION Seat Bracket Pnt Pivot Seat (blk ) Bolt Washer 13/32 x 1 x 10 Ga Clip Push-In Hinged Nut Spring Seat Cprsn 2 250 Blk Zi Screw 3/8-16 x 1.5 Washer 13/32 x 1 x 14 Ga Pan Pnt Seat (blk ) Bracket Pnt Mounting Switch Bushing Snap Blk Nyl 50 Id
KEY NO.
PART NO.
DESCRIPTION
14 72050412 Bolt Rdhd Sht Nk 1/4-20 x 1-1/2 15 134300 Spacer Split 28 x 96 Yel Zinc 16 121250X Spring Cprsn 1 27 Blk Pnt 17 123976X Nut Lock 1/4 Lge Flg Gr 5 Zinc 21 171852 Bolt Shoulder 5/16-18 Unc Blkz-2A 22 73800500 Nut 23 71110814 Bolt Hex Black 24 19171912 Washer 17/32 x 1-3/16 x 12 Ga 25 127018X Bolt Shoulder 5/16-18 x 62 26 10040800 Lockwasher NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
38
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
DECALS
12 1 2 3 7 7 4 10 12 16
11
20 14
KEY NO. 1 2 3 4 7 9 10 11
PART NO. 156868 162970 164578 164579 164425 171448 157002 4900J
DESCRIPTION Decal Instruction Operat English Decal Ins Strg Wh Decal Hood Rh Decal Hood Lh Decal Panel Side Decal Fender Logo Decal Danger English Decal Clutch/brake English
DESCRIPTION Decal Fender Decal V-belt Schematic 42" Decal Battery Danger/Poison Decal HP Engine Decal Lift Handle Decal Bypass Lt Hydro Manual Owners English
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 --
PART NO. 59192 65139 106222X 59904 106732X427 278H 9040H 106108X427 124635X 7152J 104757X428 144334
DESCRIPTION Cap Valve Tire Stem Valve Tire F Ts 15 X 6 0 - 6 Service Tube Front (Service Item Only) Rim Asm 6"front White Service Fitting Grease (Front Wheel Only) Bearing Flange (Front Wheel Only) Rim Asm 8"rear White Service Tire R Ts 18x8.5-8 C Service Tube Rear (Service Item Only) Cap Axle Blk 1 50 X 1 00 Sealant, Tire (10 oz. Tube)
7 3,9 6 11
39
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
MOWER LIFT
7 8
13 4 6 11 12 13 19 13 20 2
6 5 4
15 31 32 13 31 32
20
17 18 20 16
19
20 15
40
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
MOWER LIFT
KEY NO. 1 2 3 4 5 6 7 8 11 12 13 15 16 17 18 19 20 31 32
PART NO. 159460 159471 105767X 12000002 19211621 120183X 109413X 124526X 139865 139866 4939M 173288 73350800 130171 73800800 139868 163552 169865 73540600
DESCRIPTION Wire Asm Inner/Sprg w/Plunger Shaft Asm Lift Pin Groove E Ring #5133-62 Washer 21/32 x 1 x 21 Ga. Bearing Nylon Grip Handle Button Plunger Link Lift Lh Link Lift Rh Retainer Spring Link Front Nut Jam Hex 1/2-13 Unc Trunnion Blk Zinc Nut Lock w/Wsh 1/2-13 Unc Arm Suspension Rear Retainer Spring Bearing Pvt Lift Nut Crownlock 3/8-24
41
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
MOWER DECK
68
157 158 156 151 152 153 154 153 155 67
44
56 53 52 55 51 48 147 142 49 50 54
59
148
146 33 32 31 30
9091 92 93
94 93 92
95
34
21 21
90
1 147 142
113 111 114 115 117
2 21 21 22 23
24 25 26
116
2 16 15 14 28 20 18 29
121
119 118
121
27
3 4 5 149 13
18
114 112
115
6 19 21 10 9
118 11 119
117 116
113
42
REPAIR PARTS
TRACTOR - - MODEL NUMBER S165H42A
MOWER DECK
KEY NO. 1 2 3 4 5 6 8 9 10 11 13 14 15 16 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 40 44 45 46 48 49 50 51 52 53 54
PART NO. 165892 72140506 138017 165460 4939M 130832 850857 10030600 140296 138498 137645 128774 110485X 140329 72140505 132827 159770 73680500 134753 131267 105304X 123713X 110452X 130968X428 19111016 131491 157722 129963 153535 137266 72110614 133835 131494 19131316 73680600 140088 4497H 137729 133944 174284 131340 69180 139888 131845 133943
DESCRIPTION Mower Deck Assembly, 42" Bolt Bracket Asm Fr. Sway Bar 3/42 Bracket Asm Deck 42" Sway Bar Retainer Spring Arm, Suspension, Rear Bolt 3/8-24 x 25 Grade 8 patched Washer, Lock Washer, Hardened Blade Shaft Assembly, Mandrel, Vented Housing, Mandrel, Vented Bearing, Ball, Mandrel Stripper, Vented Mower Deck Bolt, Carriage 5/16-18 x 5/8 Bolt, Shoulder Baffle, Vortex Nut Stiffener Bracket Bracket, Deflector Mower 42" Cap, Sleeve 80 x 112 Blk Mower Spring, Torsion, Deflector 2 52 Nut, Push Phos & Oil Shield, Deflector 42" Blk Washer 11/32 x 5/8 x 16 Gauge Rod, Hinge 42" 6 75 W/G Screw Thdrol Washer Head Washer, Spacer Mower Vented Pulley, Mandrel Nut, Toplock 9/16 Bolt Fastener, Christmas Tree Pulley, Idler, Flat Washer 13/32 x 13/16 x 16 Gauge Nut Guard, Mandrel, LH Retainer Screw, Thdrol 1/4-20 x 5/8 T Washer, Hardened Roller Assembly, Cam Follower Bolt, Shoulder #10-24 Grade 5 Locknut Bolt, Shoulder 5/16-18 UNC Arm Assembly, Pad, Brake Washer, Hardened
KEY NO. 55 56 59 67 68 90 91 92 93 94 95 111 112 113 114 115 116 117 118 119 121 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 --
PART NO. 155046 165723 141043 106932X 144959 74760616 132274 73800600 19171416 1332264 132273 155197 155198 17060514 73510500 72110504 4898H 165746 73930600 19121414 143723 165890 157109 158634 165888 171977 131335 169022 165898 19091216 169670 169676 169674 169675 169671 169672 169669 17720410 72140614 130794
DESCRIPTION
Arm, Idler Spacer, Retainer Guard TUV Idler Knob V-Belt, 42" Mower Bolt Fin Hex 3/8-16 Unc x 1 Bracket Asm Noseroller Lh Nut Lock Hex w/Ins. 3/8-16 Unc Washer 17/32 x 7/8 x 16 Ga. Roller Nose 38-50 Bracket Asm. Noseroller Rh Bracket Gauge Wheel Lh Bracket Gauge Wheel Rh Screw Tapping 5/16-18 Unc Nut Keps 5/16-18unc Bolt Carr 5/16-Unc x 1/2 Bolt Shld Wheel Gauge Blk Nut Centerlock 3/8-16unc Washer 3/8 x 7/8 x 14 Ga. Bracket Extruded Gauge Wheel Arm Spring Brake Mower Bracket Arm Idler 42" Keeper Belt 42" Clutch Cable Pulley Idler Flat Bolt Carriage Idler Spring Extension Spring Return Idler Retainer Spring Yellow Washer 9/32 x 3/4 x 16 Ga. Bracket Clutch Cable Clutch Cable 42" Washer Flat 3/8" Type B Spring Retainer Spring Retention LVR CLTCH CAB Spacer Clutch Cable Rod Clutch Cable 3/8" Screw Hex Thd Cut 1/4-20 x 5/8 Bolt Rdhd Sqn 3/8-16 UNC x 1-3/4 Mandrel Assembly (Includes Key Numbers 8-10,12-15, 31 and 33) -171491 Mower Deck, Complete (Standard Deck) NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
43
SERVICE NOTES
44
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
1. This warranty does not apply to the engine, other than EHP manufactured transaxle/transmission components, battery (except as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these items. 2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by Electrolux Home Products. 3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must be maintained in accordance with the instructions furnished. 4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original purchase. 5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product. 6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard hardware and normal maintenance. 7. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact: Electrolux Home Products a division of WCI Outdoor Products, Inc. 7075 Ordan Drive Mississauga, Ontario L5T 1K6 giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it was purchased. THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from locale to locale. This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975. Electrolux Home Products a division of WCI Outdoor Products, Inc. Outdoor Products Customer Service Dept. 250 Bobby Jones Expressway Augusta, GA 30909 USA
In Canada contact:
45
SERVICE
TECUMSEH
Issued January 1980 Revised January 1991
POLICY
WARRANTY
LIMITED WARRANTIES FOR NEW PEERLESS GEAR POWER TRAIN COMPONENTS
A. Products Warranted
TECUMSEH
Peerless Gear and Machine Division of Tecumseh Products Company (Tecumseh), subject to the limitations contained below,will, at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is found upon examination by any Tecumseh Authorized Service Outlet or by Tecumsehs factory in Grafton, Wisconsin, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and Series 1100 angle drive and ONE YEAR for all other Peerless products. New Power Train Components incorporated in equipment used for commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examination within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for rental purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for THIRTY (30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date of sale to the original purchaser.
E. No Dealer Warranty
Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume for Tecumseh any other obligations or liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or limitations of Tecumsehs warranty in any way.
46
SIGHTING GUIDE
47
15 MAX.
Operate your Tractor up and down the face of slopes (not greater than 15), never across the face. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes.