‘This international standard was developed is
Develop of Terminal Standards,
Designation: F714 13
Standard Specification for
termatoniy recognized prnviptes on standardization established ia the Decision wn
uid acd Racoennen dato hse the Warld Trade Organization Techs Rays to Trade (TB) Commie
{An Armencan Nan Standars
Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside
Diameter"
“This stan Esse dr the fred designation F714: he number inumeditly following the cesienaton ites the sea of ign
option in the cae of Fvision, the Yer of last revision, A nurer in parentheses indicate the year oat reapyrova A penip
“psllon fe) iadtes an eral change since the Lis revision or repro
1. Scope?
1.1 This specification covers polyethylene (PE) pipe made
in dimensions based on outside diameters of 90 mm (3.500 in.)
and larger.
1.2 Three standard outside diameter sizing systems are
detailed: one kriown as the ISO metric system, one known as
the IPS system. and the other known as the DIPS system. See
5.25 for guidelines for special sizes
1.3 The piping is intended for new construction and inser
tion renewal of old piping systems used for the transport of
‘water, municipal sewage, domestic sewage, industrial process
liquids, effiuents, slurries, etc. in bots pressure and nonpres-
sure systems.
Nom: The user should cons the manueturer to ensue hat any
damage tothe polyethylene pipe caused by the material being transported
Will aot alfect the service life beyond nits acceptable to the use.
4. All pipes produced under this specification are pressure-
rated, See Appendix X5 for information on pressure rating.
Non 2—References and material descriptions for P2406, PES406,
PE4O8 and materials having a HDI of 1480 pst have ben removed from
Specification F714 due wo changes in Specification D33S0 and PPLTR=3.
For removed designations, refer to previous ditions of Specification
ion D3350, PPLTR-3 and PPL TR-4, The removal ofthese
alec pipelines tat are in service, See Notes 9 and 9.
1.5 This specification includes criteria for choice of raw
material, together with performance requirements and test
methods for determining conformance with the requirements,
1.6 Quality-control measures are to be take by manufac
turers, See Appendix X4 for general information on quality
control
1.7 In referee decisions, the SI units shall be used for
metric-sized pipe and inch-pound units for pipe sized in the IPS
system (ANSI B36.10) and DIPS system. In all cases, the
values given in parentheses are provided for information only.
"is sptetion i under the jst af ASTM Commitee F17 on Plaic
Piping Systems and isthe diet esponsibility of SvbcommitceFI7.26 on Olefin
Bake Pipe
Camett edition approved June 1
approves in 1981, Last peevois edie approved i 2012 a6 FTIS
TO ISUR LS
2013, Publishes June 2013, Orginly
x Dor:
18 The following safety hazards caveat pertains only to the
{est methods portion, Section 6, of this specification: This
standard does not purport ta address all of the safety concerns,
if any, associated with its use, 1 fs the responsibility of the user
of this standard to establish appropriate safety and health
practices and determine the applicability of regulatory limite
tions prior to use.
2. Referenced Documents
241 ASTM Standards?
1D1238 Test Method for Melt Flow Rates of Thermoplasties
by Exinusion Plastometer
1598 Test Method for Time-to-Failure of Plastic Pipe
Under Constant Intemal Pressure
11599 Test Method for Resistance to Short-Time Hyalraulic
Pressure of Plastic Pipe, Tubing, and Fittings
1D1600 Terminology for Abbre viated Terms Relating to Plas-
ties
2122 Test Method for Determi
‘moplastic Pipe and Fittings
12290 Test Method for Apparent Hoop Tensile Strength of
Plastic or Reinforced Plastic Pipe
2321 Practice for Underground Installation of Thermoplas-
tic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of Extemal Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
12837 Test Method for Obtaining Hydrostatic Design Basis,
{for Thermoplastic Pipe Materials or Pressure Design Basis
for Thermoplastic Pipe Products
50 Specification for Polyethylene Plasties Pipe and Fit-
tings Materials
F412 Terminology Relating to Plastic Piping Systems
F585 Guide for Insertion of Flexible Polyethylene Pipe Into
Existing Sewers
2.2 ANSI Standart:
B36.10 Standard Dimensions of Steel Pipe (1PS)*
i Dimensions of Ther
D:
2 Fe seforence ASTM stands, visi the ASTM welsite, wwwasimang. o€
fonact ASTM Crstomer Service at service@asimorg. For Anmaa! Rook af ASTM
‘Standards volume iefrmatio, refer to the stadrd's Docume Ststanary page
ine ASTM website
"Asie frm American National Stand Insite (ANSI), 25 W, nl St
4 Foor, New York, NY 10036, tipziww wns
4 Summary of Changes section appears atthe end af this standard
cere ssru antnat
Fe Te I cme eas
Nevoonion emanating mma nee
ener eye ante