Escolar Documentos
Profissional Documentos
Cultura Documentos
Metal-Enclosed/Open-Type
Description
Application
The function of the position switches (limit switches) is to produce electrical signals corresponding to the positions of the moving machinery. The 3SE3 position switches can be fitted with snap-action or slow-action contacts. 3SE3 position switches are available with 2, 3 and 4 contacts. The units are suitable for any climate.
Specifications
IEC 60 947-5-1/EN60 947-5-1 and VDE 0660 Part 200.
Positive opening The 3SE3 2 metal-enclosed position switches with snapaction contacts as well as devices with slow-action contacts can be used as safety position switches in control systems conforming to IEC 60 2041/EN 60 204-1 and VDE 0113 Part 1 . The contacts of the switch are forced open mechanically, positively-driven and reliably by the plunger (positiveopening). In order to ensure this positive opening, the position switch must be actuated in such a way that the nominal travel (pages 8/26 to 8/40) and angle for the positive opening are substantially exceeded.
Design
The 3SE3 position switches are available as metal-enclosed (in die-cast narrow or wide aluminium housings) or open-type units. The wide housing has three Pg 13.5 cable entries, the narrow enclosure has one. 3SE3 position switches with narrow enclosure and overtravel plunger, roller plunger, rod and roller crank actuators conform to EN 50 041. These specifications define the most important fixing dimensions, operating points, enclosure types and actuator types. The 3SE3 open-type position switch is only available with a plunger actuator. All actuators can be repositioned every 4 90 so that the switches can be operated from any of the four sides. The position switches with roller lever are approached perpendicular to the plunger axis and position switches with angular roller lever are approached in parallel with the plunger axis. Roller cranks, adjustable-length roller cranks and rod actuators can be continuously adjusted on the shaft. Important: The 3SE3 position switches are not permitted to be used as stops.
Technical data
Rated insulation voltage Ui Conventional thermal current Ith Pollution degree Rated operational voltage Ue Rated operational current Ie 500 V 10 A Class 3 acc. to DIN VDE 0110 AC 500 V, over AC 380 V only for equal potential AC 40 to 60 Hz DC Ie / AC-15 A 10 10 6 4 3
Ue
V 24 125 230 400 500 Short circuit protection 1) DIAZED-fuse sets Approved only for metal-enclosed position switches B, E and C ratings
Ie / AC-12 A 10 10 10 10 10
Ue
V 24 48 110 220 440
Ie / DC-12 A 10 6 4 1 0.5
Utilisation category gL/gG: 6 A, quick response: 10 A Conventional thermal current 10 A Rated voltage AC 300 V Switching capacity: Heavy Duty 2) A 600/Q 600 (A 300/ Q 300 for 3SE3 ...-8.)
Mechanical endurance Electrical endurance for AC-15 duty for DC-13 duty
30 106 make-break operations 10 106 make-break operations with 3RH11, 3RT10 16, 3RT10 17, 3RT10 24 to 3RT10 26 (3TH4, 3TF40 to 3TF43) contactors 0.5 106 make-break operations when interrupting Ie / AC-15 With DC the contact endurance depends not only on the breaking current but also on the voltage, the circuit inductance and the speed of switching. No generally valid information can be given. 6 103 make-break operations per hour 0.05 mm for repeated switching, measured at the plunger of the contact block. -40 to +85 C (-35 to +85 C for 3SE3 ...-8.) Open-type position switch Metal-enclosed position switch Electrical plug and socket connection Terminals Switching chamber IP 20 IP 40 IP 67 IP 65
Operating frequency Operating point accuracy Ambient temperature Degree of protection DIN VDE 0470 and IEC 60 529
Conductor sizes (M 3.5 screw terminals ) finely stranded with end sleeves solid Enclosure cable entry Earthing connection Enclosure Mounting position
2 1.5 mm 2 2 2.5 mm 2 Pg 13.5 thread M 3.5 inside enclosure Metal (GD - AlSi 12) any
1) Fully weld-resistant acc. to DIN VDE 0660 Part 200. 2) See Part 17. Siemens NS K 2000
8/17
Metal-Enclosed
22
14
12 22
NSK-6132a
14 24
Actuator Plunger
NSK-6148a
Actuator Enclo- Identification number 11 type sure acc. to EN 50 013 width 3SE3 000-0A switch block Order No. EN 50 041 mm Preferred type
40 56 3SE3 120-0B 3SE3 100-0B 3SE3 120-0C 3SE3 100-0C 3SE3 120-0D 3SE3 100-0D 3SE3 120-0E 3SE3 100-0E 3SE3 120-0F 3SE3 100-0F 3SE3 120-0GW 3SE3 100-0GW
Identification number 02 acc. to EN 50 013 3SE3 000-6A switch block Order No.
Identification number 20 acc. to EN 50 013 3SE3 000-7A switch block Order No. Price 1 unit
NSK-6133a
6 mm stroke
6 mm stroke
6 mm stroke
Wght. app.
kg 0.2 0.23 0.22 0.25 0.24 0.27 0.22 0.25 0.23 0.25 0.3 0.32
3SE3 120-6B 3SE3 100-6B 3SE3 120-6C 3SE3 100-6C 3SE3 120-6D 3SE3 100-6D 3SE3 120-6E 3SE3 100-6E 3SE3 120-6F 3SE3 100-6F 3SE3 120-6GW 3SE3 100-6GW
3SE3 120-7B 3SE3 100-7B 3SE3 120-7C 3SE3 100-7C 3SE3 120-7D 3SE3 100-7D 3SE3 120-7E 3SE3 100-7E 3SE3 120-7F 3SE3 100-7F 3SE3 120-7GW 3SE3 100-7GW
Overtravel plunger B
NSK-6149a
40 56
Roller plunger
40 56
NSK-6150a
40 56 40 56 40 2) 56
40 2) 56
0.35 0.37
NSK-6163a
NSK-6164a
40 56
Aluminium rod
40 56
Complete combinations
3)
Snap-action contacts Order No. 4) Complete combinations with 3SE3 120 position switches with 3SY3 110 adapter plate, 3SY3 027 base plate with locking lever and 3SY3 111 socket Complete combinations with 3SE3 120 position switches and 3SY3 111 socket 3SE3 140-1.
Slow-action make-before- Add. price break contacts Order No. 4) 3SE3 140-3.
kg 0.17
3SE3 150-1.
3SE3 150-0.
3SE3 150-3.
0.06
See for special design on pages 8/8 and 8/22. See for operation, operating speed and travels on pages 8/27 to 8/32. For multi-unit packing, see Part 17.
Safety function according to IEC 60 947-5-1-3 and DIN VDE 0660 Part 200. Design acc. to EN 50 041.
1) 2) 3) 4)
See on page 8/23. Special design with large roller, see page 8/8. Not valid for 3SE3 1.0-8. Order No. to be supplemented depending upon the selected actuator. Example: 3SE3 140-1E.
8/18
Siemens NS K 2000
Metal-Enclosed
NSK-6009a
11 21
17 25
6 mm stroke
12 22
6 mm stroke
6 mm stroke
14 22
18 26
Actuator
1
NSK-6148a
Actua- Fig. Enclo- Identification number 11 tor No. sure acc. to EN 50 013 type width 3SE3 000-1A switch block2) Order No. Price EN 50 041 mm Preferred type 1 unit
1 40 56 3SE3 120-1B 3SE3 100-1B 3SE3 120-1C 3SE3 100-1C 3SE3 120-1D 3SE3 100-1D 3SE3 120-1E 3SE3 100-1E 3SE3 120-1F 3SE3 100-1F 3SE3 120-1GW 3SE3 100-1GW 3SE3 120-1UW 3SE3 100-1UW )
Identification number 02 acc. to EN 50 013 Order No. Price 1 unit 3SE3 120-8C 3SE3 100-8C 3SE3 120-8D 3SE3 100-8D 3SE3 120-8E 3SE3 100-8E 3SE3 120-8F 3SE3 100-8F 3SE3 120-8GW 3SE3 100-8GW 3SE3 120-8UW 3SE3 100-8UW
Identification number 11 acc. to EN 50 013 3SE3 000-3A switch block Order No. Price 1 unit 3SE3 120-3B 3SE3 100-3B 3SE3 120-3C 3SE3 100-3C 3SE3 120-3D 3SE3 100-3D 3SE3 120-3E 3SE3 100-3E 3SE3 120-3F 3SE3 100-3F 3SE3 120-3GW 3SE3 100-3GW 3SE3 120-3UW 3SE3 100-3UW
Wght app.
kg 0.2 0.23 0.22 0.25 0.24 0.27 0.22 0.25 0.23 0.25 0.3 0.32 0.35 0.37
Plunger
Overtravel plunger B
NSK-6149a
40 56
Roller plunger
NSK-6150a
40 56
NSK-6151a
40 56
NSK-6152a
Angular roller lever Actuator made from mouldedplastic Roller crank A finely adjustable from 10 to 10
40 56
40 3) 56
NSK-6153a
40 3) 56
40 56
3SE3 120-1WW 3SE3 100-1WW 3SE3 120-1VW 3SE3 100-1VW 3SE3 120-1R 3SE3 100-1R 3SE3 120-1T 3SE3 100-1T 3SE3 120-1XP
NSK-6164a
Aluminium rod
40 56
NSK-6156a
Spring rod
40 56
Fork lever
10
40 56
10
11
40
11
NSK-6461a
12
NSK-6462a
12
40
3SE3 120-1XQ
0.28
13
NSK-6463a
13
40
3SE3 120-1XR
0.28
See for special design on pages 8/8 and 8/22. See for operation, operating speed and travel on pages 8/27 to 8/33. For multi-unit packing, see Part 17.
Safety function according to IEC 60 947-5-1-3 and DIN VDE 0660 Part 200. Design acc. to EN 50 041.
1) See page 8/23. 2) Switch block 3SE3 000-1A is not valid for 3SE3 120-1XP/-1XQ/-1XR and 3SE3 1.0-8. 3) Special design with large roller see page 8/8.
Siemens NS K 2000
8/19
Metal-Enclosed
13 21 31
13 21 33
17 25 31
17 25 33
14 22 32
14 22 34
18 26 32
18 26 34
6 mm stroke Identification number 12 acc. to EN 50 013, 3SE3 003-0A switch block Order No.
6 mm stroke Identification number 21 acc. to EN 50 013, 3SE3 003-1A switch block Order No.
6 mm stroke Identification number 12 acc. to EN 50 013, 3SE3 003-2A switch block Order No.
6 mm stroke Identification number 21 acc. to EN 50 013, 3SE3 003-3A switch block Order No. Price 1 unit kg 0.31 Wght. app.
Actuator Plunger
NSK-6148a
Preferred type 3SE3 303-0B 3SE3 303-1B 3SE3 303-2B 3SE3 303-3B
Overtravel plunger
NSK-6149a
3SE3 303-0C
3SE3 303-1C
3SE3 303-2C
3SE3 303-3C
0.33
Roller plunger
3SE3 303-0D
3SE3 303-1D
3SE3 303-2D
3SE3 303-3D
0.35
NSK-6150a
3SE3 303-0E
3SE3 303-1E
3SE3 303-2E
3SE3 303-3E
0.33
3SE3 303-0F
3SE3 303-1F
3SE3 303-2F
3SE3 303-3F
0.33
3SE3 303-0GW
3SE3 303-1GW
3SE3 303-2GW
3SE3 303-3GW
0.41
3SE3 303-0UW
3SE3 303-1UW
3SE3 303-2UW
3SE3 303-3UW
0.46
NSK-6164a
Special designs for 3SE3 303 and 3SE3 404 metal-enclosed position switches
Ordering advice: When ordering special designs, suffix the Order No. with -Z and the order code. Example: 3SE3 303-1E-Z A01 Design with increased corrosion protection The enclosure is double-painted. All parts subject to corrosion are made of stainless steel. with steel roller (no corrosion) For position switches with roller plunger, roller lever, angular roller lever, finely and length adjustable roller cranks, fork lever. Order No. A01 Add. price
A16
See for special design on pages 8/8 and 8/22. See for operation, operating speed and travels on pages 8/34 to 8/40. For multi-unit packing, see Part 17.
Safety function according to IEC 60 947-5-1-3 and DIN VDE 0660 Part 200.
8/20
Siemens NS K 2000
Metal-Enclosed
13 21 31 43
14 22 32 44
1 2
NSK-6594a
17 25 35 47
14 22 32 44
1 2
18 26 36 48
1 2
6 mm stroke
6 mm stroke
6 mm stroke
Identification number 22 acc. to EN 50 013 a Switch block 3SE3 000-1A s Switch block 3SE3 010-1A Order No.
Identification number 22 acc. to EN 50 013 a Switch block 3SE3 000-0A s Switch block 3SE3 010-0A Order No.
Identification number 22 acc. to EN 50 013 a Switch block 3SE3 000-3A s Switch block 3SE3 010-3A Order No. Price 1 unit
Wght. approx.
Actuator Plunger
NSK-6148a
kg 0.38
3SE3 404-1B
3SE3 404-0B
3SE3 404-2B
Overtravel plunger
NSK-6149a
3SE3 404-1C
3SE3 404-0C
3SE3 404-2C
0.4
Roller plunger
3SE3 404-1D
3SE3 404-0D
3SE3 404-2D
0.42
NSK-6150a
3SE3 404-1E
3SE3 404-0E
3SE3 404-2E
0.4
3SE3 404-1F
3SE3 404-0F
3SE3 404-2F
0.4
3SE3 404-1GW
3SE3 404-0GW
3SE3 404-2GW
0.48
3SE3 404-1UW
3SE3 404-0UW
3SE3 404-2UW
0.54
NSK-6164a
Fork lever
3SE3 404-1T
0.49
NSK-6157a
Both elements switch synchronously when two 3SE3 000.. elements are connected.
See for special designs on pages 8/8, 8/20 and 8/22. See for operation, operating speed and travel on page 8/40. For multi-unit packing, see Part 17.
Siemens NS K 2000
Safety function according to IEC 60 947-5-1-3 and DIN VDE 0660 Part 200.
8/21
Moulded-Plastic/Metal-Enclosed
Selection and ordering data
Special designs for 3SE3 100 and 3SE3 120 1) metal-enclosed position switches
Notes on ordering: Design Roller Order diameter code A01 Add. price
When ordering special designs, supple- With increased corrosion protection ment the Order No. with -Z and with The housing is double-painted, all parts subject to corrosion are made of the Order Code. stainless steel. Example: 3SE3 100-1E-Z A01 With metal roller For position switches with roller plunger, roller lever, angular roller lever, repositionable and finely and length adjustable roller cranks, fork lever. With moulded-plastic roller for 3SE3 100. GW, .UW and 3SE3 120.GW, . UW With rubber roller for 3SE3 100. GW, .UW and 3SE3 120.GW, . UW 30 mm 50 mm 50 mm
A16
3SE3 120 metal-enclosed position switches can be equipped with LEDs in the cover for status indication.
Two versions are available with indicated as well as the one or two LEDs respectively. switching status. Failure of the operational voltage can therefore be visually
When ordering special designs, supple- Direct connection to AS-Interface ment the Order No. with -Z and with for all switch types with Pg 13.5 screw gland the Order Code. Example: 3SE3 120-1GW-Z C01 3SE3 120 -1GW
Communication capability can be Safety functions can be wired The yellow bus cable is routed granted to all switch types with conventionally through the past the switch through the AS-i Pg 13.5 screw glands with this adapter module. connection terminal. adapter module. For signalling and diagnostic purposes, the NO contact is directly connected to the AS-i bus.
8/22
Siemens NS K 2000
Metal-Enclosed
Accessories
Actuator heads for 3SE3 position switches The actuator heads of the position switches can be subsequently exchanged 1).
1 2 Actuator with fixing screws Plunger with screws and gasket 3 4 Overtravel plunger with screws and gasket Roller plunger with screws and gasket Roller lever with screws and gasket 5 6 Angular roller lever with screws and gasket Actuator head with round spindle, with screws and gasket for fork lever 7 8 Roller crank 30 mm for round spindle Fork lever Roller rod adjustable length 9 10 Rod actuator Plastic rod Aluminium rod Roller crank with clamp adjustable length Spring rod with screws and gasket Lamp holder complete with glow lamp AC 230 V with LED (green) UC 24 V with LED (green, yellow) UC 24V Cover with lens, clear for narrow enclosure 8 1T .UW 3SX3 115 3SY3 024 0.03 0.054 Packed in ordered quantity Fig. No. 1 For position switches 3SE3 ... 0B 1B 3B .C Order No. Price 1 unit 3SX3 100 Weight approx. kg 0.025 Packing Units Packed in ordered quantity
3SX3 106
0.045
.D
3SX3 107
0.065
3SX3 102
0.045
3SX3 104
0.05
3SX3 211
0.105
0.105 0.015
10
1R
3SX3 126
0.05
1) Not valid for safety position switches 3SE3 120-0XB and 3SE3 ...-8. Siemens NS K 2000 Only supplied in packs.
8/23
Moulded-Plastic/Metal-Enclosed
Accessories
Quick-release devices and plug connectors for fast installation and replacement of position switches
Design 1 2 Fig. No. Order No. Price 1 unit Weight approx. kg Packing Units
3SX6 237
0.05
Socket (6-pole + PE), fr Pg 13.5 nach DIN 43 651 with connecting leads 0.75 mm2 moulded plastic for angle plug 3SY3 123 Degree of protection IP 65, for enclosed position switches with 2 or 3 contacts Angle plug 1) (manufacturer Amphenol-Tuchel) moulded-plastic Degree of protection IP 65 Socket (4-pole), for M 12 (manufacturer Lumberg) with connecting leads 0.75 mm2 for coupling box 3RX1 505 Degree of protection IP 65 Socket (5-pole), for M 12 with connecting leads 0.75 mm2 Degree of protection IP 65 Coupling box M 12 (see Part 10) Pg 13.5 moulded-plastic screw gland 6 mm thread length Adapter acc. to B, E and C for cable entry with enclosed devices from Pg 13.5 to NPT 1/2
3SY3 122
0.05
3SY3 123
0.05
3SY3 125
0.02
3SY3 126
0.02
0.05 0.01
7 8
0.1 0.01
8/24
Siemens NS K 2000
Moulded-Plastic/Metal-Enclosed
Spare parts1)
for Fig position switches No. 1 2 Switch blocks with 2 contacts with moving double-break contacts with Snap-action contacts 1 NO + 1 NC 3SE3 1.0-1.., 3SE3 230, 3SE3 404-1 3SE3 1.0-0.., 3SE3 230, 3SE3 404-0 3SE3 1.0-6.. 3SE3 1.0-7.. 3SE3 1.0-3.., 3SE3 230, 3SE3 404-2 2 1
Price 1 unit
Weight approx. kg
Packing Unit
3SE3 000-1A
0.03
Slow-action contacts 1 NO + 1 NC
3SE3 000-0A
0.03
5 5 5
Switch blocks with 3 contacts with moving double-break contacts with Slow-action contacts 1 NO + 2 NC 3SE3 303-0. 2 NO + 1 NC 3SE3 303-1. Slow-action makebefore-break contacts 1 NO + 2 NC 2 NO + 1 NC
3 3
0.05 0.05
5 5
3 3
0.05 0.05
5 5
Switch blocks with repeat plunger with 2 contacts, for position switches with 4 contacts with moving double-break contacts with Snap-action contacts Slow-action contacts Slow-action makebefore-break contacts 3SE3 404-1. 3SE3 404-0. 3SE3 404-2. 4 5 5 3SE3 010-1A 3SE3 010-0A 3SE3 010-3A 0.035 0.035 0.035 5 5 5
1) Not valid for 3SE3 ...-8. Siemens NS K 2000 Only supplied in packs.
8/25
Open-Type
Preferred type
1 unit
kg
Unit
3SE3 020-1A
0.035
mm 0,6 *
1,7
2,9
6,1**
NSK-6135b
6N
14 22
**3,5
6
21
13
NSK-8638
3SE3 020-0A
0.035
**1,7
NSK-6136b
3SE3 020-0A
21-22 13-14
NSK-6134b
0 21-22 13-14 mm
2,9 **
NSK-6137b
8N
6,1
22
14
6 25-26 17-18
3,5 mm
mm 2
3SE3 020-3A
0.035
5
** 3
6
0 25-26 17-18 mm
5,2**
8N
NSK-6139b
3,5
18 26
Intermediate piece for tandem allocation of 2-pole open-type position switches 3SY3 121 3SY3 121
3 contacts Moving double break contacts Degree of protection: Terminals IP 20, switching chamber IP 40
13-14 21-22 31-32
NSK-6138b
mm
3,5 6
NSK-6012a
13 21 33
3SE3 023-1A
0.055
5
0
14 22 32
NSK-6140b
3SE3 023-0A
0.055
** 1,5
6,1
11 N
2,6 **
NSK-6141b
mm
**1,5
3,5 6 17-18 25-26 31-32
NSK-6142b
6,1
13 N
2,6 **
NSK-6143b
14 22 34
mm 1,5 ** 3,0 **
3SE3 023-2A
0.055
2,5
4,4
11 N
2,6** 5,2**
NSK-6145b
18 26 32
NSK-6144b
NSK-6014a
17 25 33
3SE3 023-3A
0.055
5
0 2,0 3,5 6
mm 2,5**
NSK-6146b
3,5
13 N
4,4** 6,1
NSK-6147b
18 26 34
Safety function according to IEC 60 947-5-1-3 and DIN VDE 0660 Teil 200. Only supplied in packs. Siemens NS K 2000
8/26
Metal-Enclosed
Operating speed along plunger axis The operating speed must not be less than 15 mm/s for position switches (limit switches) with slow-action contacts at
DC voltage and 1 mm/s at AC voltage. Position switches with snap-action contacts should be used when the speeds are lower.
Nominal travel and rated terminals 0-line S reference line to EN 50 041 travel acc. to EN 50 041 contact closed contact open operating point on return positive opening acc. to IEC 60 947-5-1-3 perpendicular to plunger axis
Switch blocks
Nominal travel
Plunger
(made from CrNi) 3SE3 ..0-.B
Slow-action contacts
1 NO + 1 NC
21 13
NSK-8638
21-22 13-14
NSK-6042b
22
14
22 ** S=222
S=102 0 mm 9,5 **
NSK-6045 c
12 22
21-22 13-14
> = 24 > = 18
22 0,7
NSK-6132a
11 21
19
13
NSK-5981b
narrow enclosure
mm
mm
2 NO
25-26 17-18
NSK-6133a
18 26
0 21
NSK-6043b
12 ** 10,5
NSK-6046b
14 24
25-26 17-18
mm
> =18
0
NSK-5982b
mm
narrow enclosure
wide enclosure
Snap-action contacts
1 NO + 1 NC
NSK-6009a
14 22
22 * 20 19,5** S=202
NSK-6041b
21-22 13-14
13 21
S=102 0 mm 8* 10 12 **
NSK-6044b
21-22 13-14
mm
NSK-1267
13-14 23-24 19 mm
17 25
13 23
Siemens NS K 2000
8/27
Moulded-Plastic/Metal-Enclosed
Operation, operating speed and travel or angle of actuators
2 contacts Narrow and wide enclosure
Operation by a bar operating point acc. to EN 50 041 max. operation speed travel difference direction of operation Switch blocks
Nominal travel and associated terminals reference line acc. to EN 50 041 travel acc. to EN 50 041 contact closed contact open operating point on return positive opening acc. to IEC 60 947-5-1-3 perpendicular to plunger axis
Switch blocks
Nominal travel
vmax.
H
Overtravel plunger
(made from CrNi) 3SE3 ...-.C
Slow-action contacts
1 NO + 1 NC
21 13
NSK-8638
21-22 13-14
22
14
S=352
35
S=102 0 33 mm
NSK-6048b
> 40 = > 31 =
35 1,5
32 **
13,2
NSK-6051b
S=34,52
10
19,5**
12 22
21-22 13-14
NSK-6132a
11-12 21-22 34,5 0 13-14 23-24 S=32,52 0 11-12 21-22 35,5 * 34,5 S=34,52 0
11 21
NSK-5983b
narrow enclosure
mm
25-26 17-18
2 NO
NSK-6133a
17 25
H
13 23
34,5 0 mm
NSK-6049b
12,3 10,6
18 26
33,5
NSK-6052b
22 ** 25-26 17-18
14 24
30,5 ** 0
mm
NSK-5984b
narrow enclosure
wide enclosure
Snap-action contacts
1 NO + 1 NC
NSK-6009a
2 NC
21-22 13-14
NSK-6132a
13 21
11 21
35,5* S=102
14 22
S=34,52
34,5
12 22
19,5 **
NSK-6050c
0 mm 8*
10
NSK-6047b
21-22 13-14
Identification number 02
>31 ** 0
mm
8/28
Siemens NS K 2000
NSK-1270
NSK-1269
> 27,5 =
42
NSK-1268
mm
32,5
mm
mm
Moulded-Plastic/Metal-Enclosed
Operation, operating speed and travel or angle of actuators
operating point acc. to EN 50 041 Internal circuit diagram 0-line vmax. max. operating S speed Terminal designation H travel difference acc. to EN 50 013 direction of operation * **
Roller plunger
(roller made from brass on a steel spindle) 3SE3 100-.D 3SE3 120-.D (roller made from moulded plastic on a brass spindle) 3SE3 230-.D
H
Slow-action contacts
1 NO + 1 NC
2 NC
21-22 13-14
NSK-6132a
NSK-8638
11 21
22
14
21
13
12 22
21-22 13-14
53
> = 44 48 1,5
mm
> =
with make-beforebreak 1 NO + 1 NC
NSK-6010a
2 NO
25-26 17-18
NSK-6133a
NSK-5985b
17 25
wide enclosure
13 23
47
18 26
46
0 mm 12
13
24,5 **
NSK-6058b
25-26 17-18
14 24
43 ** 0
mm
NSK-6055b
44
58
Snap-action contacts
1 NO + 1 NC
21-22 13-14
NSK-6009a NSK-5986a
> =
2 NC
NSK-6132a
13 21
11 21
48 *
narrow enclosure
wide enclosure
14 22
S=472
47 0
12 22
Identification number 02
11,5 9,5 * mm
42,5 ** 0
NSK-6053b
mm
NSK-6056b
mm
NSK-1271
mm
45
mm
Siemens NS K 2000
8/29
Moulded-Plastic/Metal-Enclosed
Operation, operating speed and travel or angle of actuators
2 contacts Narrow and wide enclosure
Operation by a bar vmax. H operating point acc. to EN 50 041 max. approach angle max. trailing angle max. operating speed travel difference direction of operation
Switch blocks
Nominal travel and related terminals Internal circuit diagram S travel acc. to EN 50 041 * operating point on return Terminal designation ** positive opening acc. to acc. to EN 50 013 IEC 60 947-5-1-3
Switch blocks Nominal travel 0-line reference line acc. to EN 50 041 contact open contact closed
Roller lever
(roller made from moulded plastic) 3SE3 ...-.E
0
30 H 20 1
Slow-action contacts
1 NO + 1 NC
21 13
NSK-8638
2 NC
S=222 21-22 13-14 22 **
28,5
NSK-6068b
> 20 =
0 22
0 mm
NSK-6132a
11 21
14
12 22
NSK-1274
> 46 =
62
NSK-5989a
17 25
26,5 **
23,5
NSK-6069b
0 mm
13 23
wide enclosure For operation perpendicular to plunger axis: max. = 30 max. = 45 vmax. = 1 m/s Minimum force required in direction of operation:12 N wide enclosure
18 26
14 24
NSK-1275
Snap-action contacts 1 NO + 1 NC
NSK-6009a
13 21
20
11 21
NSK-5990a
narrow enclosure
14 22
12 22
NSK-1276
1 NO + 1 NC
21 13
NSK-8638
2 NC
NSK-6132a
65
11 21
22
14
S=602
60 1
NSK-6071b
S=602
mm
0 13-14 23-24
NSK-6133a
NSK-6072b
wide enclosure
with make-beforebreak 1 NO + 1 NC
NSK-6010a
25-26 17-18
15
> 22 =
> 20 =
>17 =
> 20 =
2 NO
13 23
17 25
a a
62 **
18 26
g g
NSK-6009a
narrow enclosure
wide enclosure :
NSK-6070b
58 * 0
mm
8/30
Siemens NS K 2000
NSK-1279
S=60+2
S=74,52
14 22
62 ** 60
NSK-6132a
13 21
11 21
21-22 13-14
NSK-5992a
Snap-action contacts 1 NO + 1 NC
2 NC
12 22
Identification number 02
NSK-1278
60
S=652
14 24
NSK-1277
60 **
12 22
11-12 21-22 60 mm 65 mm
3SE3 ...-.F
Slow-action contacts
Moulded-Plastic/Metal-Enclosed
Operation, operating speed and travel or angle of actuators
S H
Roller crank
repositionable and finely adjustable from 10 to 10 (roller made from moulded plastic) 3SE3 ...-.GW-Z A31
0
< = > =
Slow-action contacts 1 NO + 1 NC
21 13
NSK-8638
24 ** 48 21-22 13-14
NSK-6132a
S=242
11 21
0 11-12 21-22 mm 28
NSK-1280
22
70 1) 50 H 30
14
mm 0
12 22
13 ** 21-22 13-14
NSK-6062b
S=20 20
40
19
with make-beforebreak 1 NO + 1 NC
67
NSK-6010a
> =
2 NO
0 41 **
NSK-6133a
> 52 +1 =
17 25
13 23
0 mm 51
18 26
NSK-5987c
25-26 17-18
14 24
NSK-1281
13-14 23-24
narrow enclosure
vmax. = 3 m/s
Contact operation by special designs either from right or left. Minimum torque in direction of operation: 25 Ncm
Snap-action contacts 1 NO + 1 NC
NSK-6009a
13 21
S=282 0 17 * 28 36 **
NSK-6059b
14 22
mm
21-22 13-14
0 7 *
17
38 **
NSK-6060b
21-22 13-14
Roller crank
adjustable length (roller made from moulded plastic), finely adjustable from 10 to 10 3SE3 230-.U, 3SE3 1..-.UW
0
> 20 =
Slow-action contacts 1 NO + 1 NC
21 13
NSK-8638
13 **
0 11-12 21-22 18
NSK-1282
19
22
14
40
12 22
< 80 = > = 50
with make-beforebreak 1 NO + 1 NC
NSK-6010a
17 25
33**
13 23
0 40
NSK-1283
13-14 23-24
18 26
NSK-5994b
14 24
NSK-6009a
Contact operation either from right or left or from right and left Minimum torque in direction of operation: 25 Ncm 1) Max. operating angle 70. Siemens NS K 2000
Snap-action contacts 1 NO + 1 NC
13 21
0 7 * 17 38 ** 21-22 13-14
NSK-6074b
14 22
8/31
Moulded-Plastic/Metal-Enclosed
Operation, operating speed and travel or angle of actuators
2 contacts Narrow and wide enclosure
Operation by a bar
Switch blocks
vmax.
Nominal travel and related terminals Internal circuit diagram S travel acc. to EN 50 041 * operating point on return Terminal designation ** positive opening acc. to acc. to EN 50 013 IEC 60 947-5-1-3 perpendicular to plunger axis
Nominal travel reference line acc. to EN 50 041 contact closed contact open perpendicular to plunger axis
Rod actuator
(made from aluminium or moulded plastic) finely adjustable from 10 to 10 3SE3 3SE3 3SE3 3SE3 230-.W 230-.V 1..-.WW 1..-.VW
0
9 40 A 40
<70 1) = > 50 =
Slow-action contacts 1 NO + 1 NC
21 13
NSK-8638
2 NC
0 20
NSK-1392 NSK-6132a
21-22 13-14 46
11 21
0 11-12 21-22 24
NSK-1284
22
14
12 22
0 26
43 **
NSK-1393
0 13-14 23-24
NSK-1285
17 25
25-26 17-18
13 23
48
18 26
14 24
NSK-5995b
narrow enclosure
NSK-6009a
A switching range B bottom edge of actuating device vmax. = 3 m/s Contact operation either from right or left or from right and left Minimum force required in direction of operation: 25 Ncm
Snap-action contacts 1 NO + 1 NC
13 21
0 7 * 24 38 ** 21-22 13-14
NSK-1391
14 22
Spring rod
3SE3 ...-1R
R o d a p p ro a c h
Snap-action contacts 1 NO + 1 NC
1 5
1 )
M in im w h e n (s a fe th e s M a w h (d e th e
u m o p e ty p o w itc h
NSK-6009a
13 21
10 21-22 13-14 4*
NSK-6073b
14 22
x im e n s tr a c
1 0 0
1 5
3 0
A N S K -5 9 9 3 c
narrow enclosure
wide enclosure
Can be approached from any direction vmax. = 1 m/s Minimum force required along plunger: 12 N With side deflection on the peak: 2.5 N
8/32
1 0 0
Siemens NS K 2000
Metal-Enclosed
0-line
reference line acc. to EN 50 041 contact closed contact open operating point on return
Fork lever
(roller made from moulded plastic) 3SE3 100-1T, 3SE3 120-1T
45 40 _
Snap-action contacts 1 NO + 1 NC
NSK-6009a
13 21
64
10
< = > =
14 22
21-22 13-14
-9,5
0 mm
> =
15 * 17
21-22 13-14
NSK-6066b
NSK-5988a
narrow enclosure
wide enclosure
vmax. = 2 m/s
Overtravel plunger
(perpendicular to the plunger axis)
5,2 x 2 30 8 16 5,2 7,5 17,5 58
Snap-action contacts 1 NO + 1 NC
NSK-6009a
30 N
NSK-8137
mm 5 4 2,8
NSK-8136
3SE3 120-1XP
14 22
4,8
Identification number 11
NSK-8133a
mm
Roller plunger
with roller in vertical position (perpendicular to the plunger axis) 3SE3 120-1XQ
Rolle 30 5,2 x 2 10 16 63
NSK-6009a
mm 5 4 2,8
NSK-8136
14 22
4,8
Identification number 11
NSK-8135a
7 8,7 mm 0 12
vmax. = 1 m/s
Roller plunger
with roller in horizontal position (perpendicular to the plunger axis) 3SE3 120-1XR
NSK-8134a
NSK-6009a
5,2 x 2
mm 5 4 2,8
NSK-8136
17,5
5,2 7,5
14 22
4,8
Identification number 11
7 8,7 mm 0 12
vmax. = 1 m/s
NSK-8137
Siemens NS K 2000
Rolle 30
10
16
63
Snap-action contacts 1 NO + 1 NC
13 21
NSK-8137
13 21
Snap-action contacts 1 NO + 1 NC
vmax. = 1 m/s
12
0 7
13 21
8,7
30 N
30 N
8/33
Metal-Enclosed
vmax. H
operating point acc. to EN 50 041 max. operating speed travel difference direction of operation
Plunger
(made from CrNi)
H
Slow-action contacts 1 NO + 2 NC
NSK-6011b
13 21 31
3SE3 303-.B
> 24 = >18 =
22 0,7
14 22 32 0
22 ** 20 mm 10 **
Identification number 12
S=220,7
0 13 21 33
13-14 21-22 33-34
NSK-6077b
NSK-5996a
mm
10 1 10 1 30
>18 > 20 = =
2 NO + 1 NC
S=101 0 22** 20 mm 10 **
NSK-6082b NSK-6012a
18 N
13,5
28
14 22 34
S=220,7
Identification number 21
NSK-5997a
NSK-6078b
mm
16 N
17-18 25-26 31-32 0 12 17-18 25-26 31-32
17 25 31
18 26 32
22 ** 21 20,5**
mm
10**
12,5**
NSK-6083b
Identification number 12
NSK-6079b
mm
2 NO + 1 NC
NSK-6014a
18 N
17-18 25-26 33-34 0 11
NSK-6084b
17 25 33
18 26 34
21,5
mm 21** 20
11,5** 13,5
Identification number 21
8/34
NSK-6080b
mm
Siemens NS K 2000
Metal-Enclosed
Overtravel plunger
H
3SE3 303-.C
> 40 = > 31 =
NSK-6011b
Slow-action contacts 1 NO + 2 NC
13 21 31
35 1,5
14 22 32
Identification number 12
0
10
16 **
NSK-6085b
NSK-5998b
mm
2 NO + 1 NC
30
> 20 =
NSK-6012a
10 1,5 10 1,5
37 N
S=101,5 0 35,3 mm S=351,5 33,3 31,5 **
NSK-6090b
13 21 33
10
13,5
16 **
14 22 34
42
> 27,5 =
Identification number 21
NSK-5999a
NSK-6086b
mm
35 N
0 11,5 18,5 **
NSK-6087b
17 25 31
18 26 32
mm
10
12
16**
NSK-6091b
Identification number 12
34,3
30** 0 mm
2 NO + 1 NC
17-18 25-26 33-34
NSK-6014a
37 N
0 11
NSK-6092b
17 25 33
18 26 34
35
mm 34,5 33,3
11,5 13,5
17,5 **
Identification number 21
30,5** 0
NSK-6088b
mm
Siemens NS K 2000
8/35
Metal-Enclosed
Roller plunger
(roller made from brass on a steel spindle) 3SE3 303-.D
> = 40 48 1,5
Slow-action contacts
1 NO + 2 NC
NSK-6011b
13 21 31
53
S=152,5 0 19,5
NSK-6097a
35 N
13-14 21-22 31-32
14 22 32 0
NSK-6093b
> =
Identification number 12
S=481,5 45,5
47,5
mm
16,5
22**
NSK-6000b
44**
mm
NSK-6012a
NSK-6094a
30 20
> =
15 2,5 15 2,5
2 NO + 1 NC
S=152,5 0 16,5 19,5 22 ** 13-14 21-22 33-34
37 N
14 22 34
58
47,5
Identification number 21
S=481,5 45,5 44 **
mm
NSK-6098b
> =
44 +1
NSK-6001b
mm
vmax. = 1 m/s
with make-before-break 1 NO + 2 NC
17-18 25-26 31-32
NSK-6013a
17 25 31
18
NSK-6099b
35 N
17-18 25-26 31-32
NSK-6095a
18 26 32
mm 47,5 46 44 ** 42,5**
16,5 18,5
22** 24,5 **
Identification number 12
46,5
mm
2 NO + 1 NC
17-18 25-26 33-34
NSK-6014a
37 N
0 17
NSK-6100b NSK-6096a
17 25 33
18 26 34
mm
17,5 19,5
24**
Identification number 21
47
46,5 45,5
43 ** 0 mm
8/36
Siemens NS K 2000
Metal-Enclosed
operating point acc. to EN 50 041 travel difference max. approach angle max. approach angle max. trailing angle max. operating speed direction of operation
Roller lever
(roller made from moulded plastic) 3SE3 303-.E
0
30 H 20 1
Slow-action contacts
1 NO + 2 NC
NSK-6011b
13 21 31
> 20 =
15 N
0
14 22 32
62
Identification number 12
> 46 =
20**
mm
2 NO + 1 NC
NSK-6012a
17 N
S=201 13-14 21-22 33-34 26
NSK-6102b
13 21 33
NSK-6002a
14 22 34
g b
Identification number 21
20 **
mm
with make-before-break 1 NO + 2 NC
NSK-6013a
17 25 31
23
NSK-6103b
15 N
24,5**
20 **
mm
18 26 32
NSK-6003a
Identification number 12 2 NO + 1 NC
NSK-6014a
For operation perpendicular to plunger axis max. = 30, vmax. = 1 m/s max. = 45, vmax. = 2.5 m/s max. = 45 For operation along plunger axis vmax. = 1.5 m/s
17 25 33
21,8
17 N
26
23**
NSK-6104b
mm
18 26 34
Identification number 21
Slow-action contacts
1 NO + 2 NC
13-14 21-22 31-32
NSK-6011b NSK-6105b
15 N
13-14 21-22 33-34 63
NSK-6106b
13 21 31
14 22 32
Identification number 12
0
63
2 NO + 1 NC
NSK-6012a
17 N
S=601 S=601 60 ** 0 mm 60 ** 0 mm
13 21 33
NSK-6004a
> 17 =
> 20 =
14 22 34
1 NO + 2 NC
NSK-6013a
15 N
NSK-6107b NSK-6108b
17 25 31
64
b
NSK-6005a
18 26 32
Identification number 12 2 NO + 1 NC
62
63 **
17 N
60,5 60 ** 61**
For operation along plunger axis max. = 30, vmax. = 1 m/s max. = 45, vmax. = 2.5 m/s max. = 45, vmax. = 2.5 m/s
NSK-6014a
17 25 33
18 26 34
mm
mm
Identification number 21
Siemens NS K 2000
8/37
Metal-Enclosed
Roller crank
repositionable and finely adjustable from 10 to 10 (roller made from moulded plastic)
20
Slow-action contacts
0
NSK-6011b < = > =
20 3
70 1) 50 H 30
1 NO + 2 NC
13 21 31
14 22 32
19
67
Identification number 12
> = NSK-6006c
52 +1
> =
2 NO + 1 NC
NSK-6012a
13 21 33
vmax. = 3 m/s
Contact operation either from right or left or from right and left.
14 22 34
Identification number 21
47
20**
NSK-6112b
with make-before-break 1 NO + 2 NC
NSK-6013a
17 25 31
S=203 0 32
NSK-6113b
18 26 32
Identification number 12
mm 0
20 ** 34
37 **
NSK-6114b
20 **
40 **
2 NO + 1 NC
NSK-6014a
17 25 33
26 31**
NSK-6115b
18 26 34
Identification number 21
0 28
NSK-6116b
33** 47
1) Max. operating angle 70, max. deflection for adjustment purposes 90.
8/38
Siemens NS K 2000
Metal-Enclosed
vmax. **
Internal circuit diagram operating point acc. to EN 50 041 max. approach angle Terminal designation max. trailing angle acc. to EN 50 013 max. operating speed max. bar distance or angle to ensure positive opening of snap-action contacts acc. to DIN VDE 0113 direction of operation
Roller crank
repositionable and finely adjustable from 10 to 10 (roller made from moulded plastic)
b 0
> 20 =
Slow-action contacts
1 NO + 2 NC
NSK-6011b
19
13 21 31
14 22 32
< 80 = > 50 = <70 1) = > 50** =
20**
NSK-6117b
3SE3 303-.UW
Identification number 12
2 NO + 1 NC
NSK-6007c NSK-6012a
13 21 33
14 22 34
max. = 30 max. = 30 vmax. = 3 m/s Contact operation either from right or left or from right and left.
Identification number 21
with make-beforebreak 1 NO + 2 NC
NSK-6013a
34
17 25 31
20**
40
18 26 32
Identification number 12 2 NO + 1 NC
NSK-6014a
28
NSK-6120b
17 25 33
18 26 34
Identification number 21
Siemens NS K 2000
8/39
Metal-Enclosed/Open-Type
Operation, operating speed and travel or angle
vmax.
0-line
**
reference line acc. to EN 50 041 contact closed contact open positive opening to IEC 60 947-5-1-3
Rod actuator
finely adjustable from 10 to 10 (rod made from moulded plastic or aluminium)
max. 212 200 > 100 =
Slow-action contacts
0
9 40 B A 40
<70 = > 50 =
1)
1 NO + 2 NC
NSK-6011b
13 21 31
14 22 32
20**
NSK-6117b
Identification number 12
2 NO + 1 NC
NSK-6008b NSK-6012a
13 21 33
14 22 34
A B
Identification number 21
vmax. = 3 m/s
Contact operation either from right or left or from right and left.
with make-before-break 1 NO + 1 NC
NSK-6013a
17 25 31
34
18 26 32
20**
40
Identification number 12
2 NO + 1 NC
NSK-6014a
17 25 33
28
NSK-6120b
1) Max. operating angle 70, max. deflection for adjustment purposes 90.
18 26 34
Identification number 21
3SE3 404 metal-enclosed position switches 4 contacts Wide enclosure The data for operation, operating speed, travel and angle of operation is the same as for the metal-enclosed position switches with 2 contact blocks. Contact blocks with 2 contacts are used for position switches with 4 contacts.
3SE3 020 and 3SE3 023 open-type position switches 2 and 3 contacts Moving double break contacts Degree of protection: Terminals IP 20, switching chamber IP 40
Actuator Operation Type A mm A** mm
Plunger
(made from CrNi)
b a
Actuators can be in the form of an actuating 3SE3 020-0A bar, cam, stop etc. For operation perpendicular to plunger axis 3SE3 020-1A max. = 30, vmax. = 0.5 m/s 3SE3 020-3A max. = 30 For operation along plunger axis vmax. = 1.5 m/s A actuating bar distance = Distance 3SE3 023-0A from the middle of the mounting holes to the lower edge of the actuating bar 3SE3 023-1A 3SE3 023-2A A** Actuating bar distance, to guarantee 3SE3 023-3A positive opening of the snap-action contacts acc. to DIN VDE 0113.
NSK-6172a
15 15 15
17.5
= 20
>
15
15 15 15
8/40
Siemens NS K 2000