Escolar Documentos
Profissional Documentos
Cultura Documentos
kr
ongHwa Entec Fresh Water Generators are the equipment that convert sea water or exhausted dirty water to pure water for drinking, boiler make-up, domestic use on ship and small power station. At that time, sea water is evaporated at about 45 C ~50 C as it passed the inside of heater under the high vacuum condition and the separated pure vapor is converted to fresh water on condenser.
Plate Type
Tubular Type
Type
Single stage DF3 DF3 DF7 DF7 DF7 DF13 DF13 DF13 DF13 DF23 DF23 DF35 DF35 DF35 DF35
Connection
JIS 40 40 40 65 65 65 65 65 80 100 100 125 125 150 200
Heat consumption
KW 110 160 220 310 360 460 540 600 750 910 1080 1220 1360 1520 1850
Tubular Type
Working Principle
The main engine jacket cooling water circulates the outside of the vertical tube in heating section and the sea water to be distilled is sent to the bottom cover of this section. Then some of the sea water is converted into vapour when it goes up through the heated tubes. The vapour, through the demisters, is condensed on the outer surface of the tubes of the distilling condenser and the resultant distillate is led to the suction of the distillate pump. In the meantime the non-condensable gases and brine are extracted and discharged to overboard by the combination ejector.
Type
Single stage DX- -5 DX- -10 DX- -15 DX- -20 DX- -25 DX- -30 DX- -35 DX- -40
Connection
JIS 65 80 80 100 100 125 125 125
Heat consumption
KW 141 282 423 564 705 846 987 1128
FW pump consumption(60Hz)
bar 2 3 3 3 3 3 3 3 KW 0.4 1.5 1.5 1.5 1.5 1.5 1.5 1.5
8 5 T 5
T
30 4 5 T T5
31 6
Delivery extent Dong-hwa Air / Vacuum Distilled water flexible hoses chemical dosing equipment electrical wire / Dong-hwa electrical wire yard or customer
N.P
18
19 33 34
20
1 27 14 34 17
29
32 12 33
17
17
A
16 15 26 Max. back pressure 1.8 Bar
C E
Over board
10
28
NO. 1 2 3 4 5 6 7
DESCRIPTION EVAPORATOR CONDENSER TWIN EJECTOR VACUUM GAUGE THERMOMETER DISTILLER BASE FLANGE DISTILLER COVER
NO. 8 9 10 11 12 13 14
DESCRIPTION FLOW SIGHT GLASS FRESH WATER PUMP SALINITY SENSOR SALINITY INDICATOR(controller) SOLENOID V/V CONTROL PANEL PRESSURE GAUGE
NO. 15 16 17 18 19 20 21
DESCRIPTION PAN CHECK VALVE FLOW METER FOR DISTILLED WATER CHEMICAL DOSING UNIT DEMISTER FEED VALVE ORIFICE EJECTOR PUMP(Option)
NO. 22 23 24 25 26 27 28
DESCRIPTION SEA WATER INLET JACKET WATER INLET JACKET WATER OUTLET SEA WATER OUTLET DISTILLED WATER OUTLET BRINE OUTLET SEA WATER FILTER (Max. 5mm)
NO. 29 30 31 32 33 34
DESCRIPTION AIR / VACUUM SUCTION LINE SAFETY VALVE VACUUM BREAKER DRAIN LINE VALVE COMPOUND GAUGE CHECK VALVE
DISTILLER BASE FLANGE CONDENSER PLATES EVAPORATOR PLATES CONTROL PANEL END PLATE SALINITY CONTROLLER
THERMOMETER THERMOMETER
VACUUM BREAK
N.P
VACUUM GAUGE VACUUM ADJUSTING VALVE SEA WATER INLET DISTILLED WATER SUCTION LINE CONTROL PANEL JACKET WATER INLET COMP. GAUGE ORIFICE HIGH SALINITY WATER RETURN LINE PURGE METER COMP. GAUGE FLOW METER FRESH WATER OUTLET
Dimension List
Type
DF3/5 DF7/10 DF13/15 DF13/20 DF13/25 DF23/30 DF23/35 DF35/40 DF35/45 DF35/50 DF35/60
NAME PLATE SAFETY VALVE FOLLOWER JACKET WATER OUTLET SIDE MEMBER DISTILLATE PUMP SEA WATER OUTLET TWIN EJECTOR BRINE LINE ZINC SIGHT GLASS PRESS GAUGE DISTILLATE PUMP S.W FEED LINE SIGHT GLASS AIR SUCTION LINE FEED VALVE SOLENOID VALVE
A
610 1020 1020 1080 1080 1276 1276 1276 1276 1276 1276
B
1013 1400 1550 1660 1660 1838 2100 2200 2200 2200 2200
C
810 808 625 780 780 1210 900 900 900 900 900
D
935 1042 1065 1280 1450 1785 1440 1590 1700 1750 1800
E
1460 1500 1435 1550 1820 2255 1710 1810 2000 2100 2200
SALINITY SENSOR
Approx. Weight(kg) Empty Operation 400 310 550 400 580 430 600 450 850 640 900 675 950 700 1100 850 1200 890 1250 910 1500 1130
N P
SALINITY CONTROLLER
ALARM OFF DEC INC SET START /STOP
JK-201
TO OVERBOARD
BACK PRESS. MAX. 8 mAq
0~100C
PREHEATER CONDENSER
T 0~100C
Sea chest
4.8 bar
13
11
J.W. OUTLET
JACKET WATER
III T
0~150C
HEATER
5V
0~150C
JACKET WATER
III J.W. INLET DISTILLED WATER C -760mmHg~4K V2 V6 SEA WATER FEEDING
Dimension List
Type L
1480 1680 1835 1880 2050 2250 2400 2500
DRIV'G S. WATER
B
820 980 1030 1060 1150 1330 1380 1400
H
1430 2005 1975 1680 1850 2080 2100 2205
C
1655 1840 2030 2250 2310 2470 2510 2550
A
650 830 850 990 1200 1500 1500 1500
V EJECTOR PUMP
SALINITY INDICATOR ALARM POWER SUPPLY V4 V4 FM IV PRODUCT WATER OUTLET V 13 DISTILLATE PUMP SC
FRESH WATER
BACK PRESS. MAX. 18 mAq
C -760mmHg~4K V 1 V6
LEGEND PRESSURE GAUGE COMPOUND GAUGE VACUUM GAUGE THERMOMETER SALINITY CELL FLOW METER ORIFICE AIR VENT VALVE GLOBE VALVE SWING CHECK VALVE PRESS. REGULAT. VALVE 2-WAY SOLENOID VALVE 3-WAY COCK SIGHT GLASS RELIEF VALVE
HEATING LINE S.W LINE F.W LINE ELECTRIC WIRING YARD SUPPLY
V T SC FM A
DXDXDXDXDXDXDXDX-
Approx. Weight(kg) Empty Operation Ejector P/P 120 780 680 120 900 750 128 1000 850 140 1350 1140 175 1370 1145 175 1400 1150 175 1570 1200 187 1650 1320
Capacity(ton/day)
40 35 30 25 20 15 10 5 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 Steam Consumption(ton/hr)
Optional equipment
-Hot water loop module for steam boosting of jacket water. -Extended control panel with motor starters and salinometer. -Individual single motor starters and salinometer. -Fresh water pH adjustment filter. -Fresh water disinfection equipment.
www.dh.co.kr
HEAD OFFICE AND FACTORY 1575-6, Songjeong-Dong, Gangseo-Gu, Busan, 618-270, Korea Tel :+82-51-970-1000 Fax : +82-51-970-1001 R&D CENTER #1219-1, Jisa-Dong, Gangseo-Gu, Busan, Korea Tel :+82-51-970-0711 Fax : +82-51-970-0730
SEOUL OFFICE
Room No, 1515 Hanshin Core Officetel 11-9 Shinchun-Dong, Songpa-Gu,Seoul 138-733, Korea Tel :+82-2-421-4707 Fax :+82-2-421-4708 SHANGHAI OFFICE DongHwa Entec Shanghai Branch Office No 68 Lane 377 Chenhui Rd Shanghai Zhangjiang Hi-Tech Park 201203 P.R. China Tel : +86-21-5027-1828 Fax : +86-21-5027-1878
www.dh.co.kr
ongHwa Plate Heat Exchangers are used in the industrial, marine, food and dairy sectors. DongHwa works at high quality level, based on an experienced staff, with regards to both production and calculation of Plate Heat Exchangers. DongHwa can, with the help of specially developed computer programs, quickly calculate an optimal solution to any plate heat exchanger application, based on the customers demands. The calculated Plate Heat Exchanger is documented for the customer on a well-arranged and easily read data list.
Working Principle
Port hole
Gasket is attached to the heat plate which forms flow channel and acts seal up the fluid not to leak to the outside. The number of the heat plate is determined according to the amount of fluid, physical properties of fluid, the pressure drop and thermal condition. The covers prevent the plates bended from the difference of pressure. In the assembly of plate, the surface with gasket is directed to the fixed cover and each plate is hanged in opposite direction alternately. And two fluids cannot be mixed and separated by a thin plate. One fluid always flows in "A" channel and the other fluid always flow in "B" channel.
B PLATE
Follower Cover Roller Assembly Carrying Bar Head Cover
A PLATE
Guide Bar
Plate Pack
High turbulent flow High heat transfer coefficient Perfect temperature approach High pressure drop
LOW -THETA PLATE
Low turbulent flow Low heat transfer coefficient High temperature approach Low pressure drop
High-theta Plate
Low-theta Plate
High-theta Plate
Low-theta Plate
Plate Design
The construction of the inlet part makes a perfect distribution of the liquids across the heating surface. The inlet part is increased and supplied with grooves preventing dead spots which may cause the growth of bacteria or seaweeds in the plate heat exchanger. The inlet with grooves secures a strong inlet part with a minimum of contact points. The inlet parts are constructed with a leakage drained zone fulfilling the 3A specifications. The plate pattern is constructed to obtain a high thermal efficiency. The pattern is available in two designs with different angle sizes giving high respectively low turbulent flow. Combining these in a plate pack and optimal plate composition can be calculated. The angle and fishbone pattern has appeared to male the best heat transmission by a given pressure drop.
Characteristics
Dead Zone
Others
Clip Gasket
The gasket can be fixed tightly and quickly on the heat plate in the optimum condition with the dual fixing device (snap on type), and is designed and manufactured to have the glue type and non-glue type so that it can be selected according to the usage.
Ours
Improved Wave
Even the biggest model also can be assembled or disassembled by 1 or 2 persons. As it is designed to have a dual fixing method of the insert-typed plate and insert-typed gasket, there is no sliding on the plates. It prevents sliding and an assembling failure even when a nonskilled novice disassemble or assemble the device. (Excellent maintenance against materials with high viscosity such as oils for LO cooler or oil heater)
FOULING FACTOR
r ula Tub
Plate Type
TIME
Temperature Approach
The turbulent flow, promoted by the wave pattern of the heat plates, enables a very high heat transfer coefficient. Proximity Limit: 1
Insert Gasket
GINE MAIN EN
R ENGINE GENERATO
Application
Marine Application and Engines, Architecture Industry, Automobiles Industry, Textile Industry, Pulp and Paper Industry, Chemical Industry, Steel Industry, Mechanical Industry, Food Industry, HVAC, Power Stations, Surface Treatment
Marine application
Dimension - C( 1.5%) mm Model Max. Flow Area of Plate Plate Hole Dia Max.Conn.Dia. Dimension - A Dimension - B
(3.05+t) x n (2.7+0.5) x n (2.7+0.5) x n (2.7+0.5) x n HT150 420 0.25 150 150 720 1189 (2.95+t) x n HT232 950 0.86 224 250 886 1980 (3.05+t) x n HT353 2400 2.45 355 400 1115 3532 (3.35+t) x n HT151 420 0.55 150 150 720 1663 (2.95+t) x n HT233 950 1.02 224 250 886 2168 (3.05+t) x n HT354 2400 3.15 355 400 1115 4152 (3.35+t) x n HT152 420 0.85 150 150 720 2137 (2.95+t) x n HT234 950 1.35 224 250 886 2543 (3.05+t) x n HT451 3400 1.23 430 500 1390 2698 (3.7+t) x n HT153 420 1.15 150 150 720 2611 (2.95+t) x n HT235 950 1.85 224 250 886 3105 (3.05+t) x n HT452 3400 2.0 430 500 1390 3264 (3.7+t) x n
Dimension - C( 1.5%) mm Model Max. Flow Area of Plate Plate Hole Dia. Max.Conn.Dia. Dimension - A Dimension - B
Dimension - C( 1.5%) mm Model Max. Flow Area of Plate Plate Hole Dia. Max.Conn.Dia. Dimension - A Dimension - B
Dimension - C( 1.5%) mm Model Max. Flow Area of Plate Plate Hole Dia. Max.Conn.Dia Dimension - A Dimension - B t : Heat Plate Thickness
Dimension - C( 1.5%) mm
www.dh.co.kr
HEAD OFFICE AND FACTORY
1575-6, Songjeong-Dong, Gangseo-Gu, Busan, 618-270, Korea Tel :+82-51-970-1000 Fax : +82-51-970-1001
R&D CENTER
SEOUL OFFICE
SHANGHAI OFFICE
#1219-1, Jisa-Dong, Gangseo-Gu, DongHwa Entec Shanghai Branch Office Room No, 1515 Hanshin Core Officetel 11-9 Busan, Korea Shinchun-Dong, Songpa-Gu,Seoul 138-733, Korea No 68 Lane 377 Chenhui Rd Shanghai Zhangjiang Tel :+82-51-970-0711 Fax : +82-51-970-0730 Tel :+82-2-421-4707 Fax :+82-2-421-4708 Hi-Tech Park 201203 P.R. China Tel : +86-21-5027-1828 Fax : +86-21-5027-1878
www.dh.co.kr
ankers carrying different kinds of liquid products must have their tanks thoroughly cleaned before loading another kind of cargo. In product and parcel tankers the tanks have to be washed with hot sea and fresh water to ensure the required degree of tank cleanliness. The water is heated by steam of other heating medium in a heater can be used for this heating duty and is supplied to the tank washing machines through a tank cleaning system on deck. Every tank is provided with one or more washing machine facilities.
1. HEATED WATER : SEA WATER(TEMP. FROM 20 TO 80) 2. HEATING SOURCE : STEAM(6~10Kg/cm2G) 3. DRAIN OUTLET TEMP. : 90 AND BELOW 4. TUBE : AL-BRASS(JIS C6872T) 16mm(O.D.)1mm (OPTION 1.2t, 1.4t) 5. TUBE SHEET : NAVAL BRASS(JIS C4621P) 6. TUBE SIDE MAX. DESIGN PRESS. : 17Kg/cm2G 7. SHELL SIDE MAX. DESIGN PRESS. : 11Kg/cm2G
Capacity Table
STEAM S.W FLOW RATE(M3/HR) MODEL NUMBER L /A STEAM PRESS. STEAM CONSUMPTION(Kg/hr) SURFACE AREA(M2) STEAM INLET SIZE S.W IN & OUTLET SIZE WEIGHT OF T.C.H BODY MODEL NUMBER L /A STEAM PRESS. STEAM CONSUMPTION(Kg/hr) SURFACE AREA(M ) STEAM INLET SIZE S.W IN & OUTLET SIZE WEIGHT OF T.C.H BODY MODEL NUMBER L /A STEAM PRESS. STEAM CONSUMPTION(Kg/hr) SURFACE AREA(M ) STEAM INLET SIZE S.W IN & OUTLET SIZE WEIGHT OF T.C.H BODY MODEL NUMBER L /A STEAM PRESS. STEAM CONSUMPTION(Kg/hr) SURFACE AREA(M2) STEAM INLET SIZE S.W IN & OUTLET SIZE WEIGHT OF T.C.H BODY MODEL NUMBER L /A STEAM PRESS. STEAM CONSUMPTION(Kg/hr) SURFACE AREA(M2) STEAM INLET SIZE S.W IN & OUTLET SIZE WEIGHT OF T.C.H BODY
2 2
TYPE A B C TCH-50S See 251 320 TCH-55S Capacity 286 380 TCH-60S Table 286 400 TCH-70S 381 480
K 650
100 TCH-50-1 2061/3223 10151.2 35 10K-150A 10K-80A 16K-150A 1340 TCH-50-1 2061/3223 10127.7 35 10K-125A 10K-80A 16K-150A 1340 TCH-50-1 2061/3223 10107.9 35 10K-150A 10K-80A 16K-150A 1340 TCH-50-1 2061/3223 10090.8 35 10K-125A 10K-80A 16K-150A 1340 TCH-50-1 2061/3223 10076 35 10K-125A 10K-80A 16K-150A 1200
120 TCH-50-2 2355/3517 12181.4 40 10K-150A 10K-80A 16K-150A 1430 TCH-50-2 2355/3517 12153.2 40 10K-150A 10K-80A 16K-150A 1430 TCH-50-2 2355/3517 12129.4 40 10K-150A 10K-80A 16K-150A 1430 TCH-50-1 2061/3223 12108.9 35 10K-125A 10K-80A 16K-150A 1430 TCH-50-1 2061/3223 12091.2 35 10K-125A 10K-80A 16K-150A 1340
140 TCH-50-3 2649/3811 14211.7 45 10K-150A 10K-80A 16K-150A 1520 TCH-50-3 2649/3811 14178.8 45 10K-150A 10K-80A 16K-150A 1520 TCH-50-3 2649/3811 14151 45 10K-150A 10K-80A 16K-150A 1520 TCH-50-3 2649/3811 14127.1 45 10K-150A 10K-80A 16K-150A 1520 TCH-50-2 2355/3517 14106.4 40 10K-150A 10K-80A 16K-150A 1430
160 TCH-55-2 2606/3880 16241.9 55 10K-200A 10K-100A 16K-200A 1745 TCH-55-1 2369/3643 16204.3 50 10K-150A 10K-100A 16K-200A 1745 TCH-55-1 2369/3643 16172.6 50 10K-150A 10K-100A 16K-200A 1645 TCH-55-1 2369/3643 16145.2 50 10K-150A 10K-100A 16K-200A 1645 TCH-55-1 2369/3643 16121.6 50 10K-150A 10K-100A 16K-200A 1645
180 TCH-60-2 2388/3675 18272.1 60 10K-200A 10K-100A 16K-200A 1890 TCH-60-2 2388/3675 18229.9 60 10K-200A 10K-100A 16K-200A 1890 TCH-55-2 2606/3880 18194.2 55 10K-200A 10K-100A 16K-200A 1745 TCH-60-1 2189/3476 18163.4 55 10K-150A 10K-100A 16K-200A 1745 TCH-60-1 2189/3476 18136.8 55 10K-150A 10K-100A 16K-200A 1780
200 TCH-60-4 2786/4073 20302.4 70 10K-200A 10K-100A 16K-200A 1990 TCH-60-3 2587/3874 20255.4 65 10K-200A 10K-100A 16K-200A 1990 TCH-60-3 2587/3874 20215.8 65 10K-200A 10K-100A 16K-200A 1990 TCH-60-2 2388/3675 20181.5 60 10K-200A 10K-100A 16K-200A 1890 TCH-60-2 2388/3675 20152 60 10K-200A 10K-100A 16K-200A 1890
240 TCH-60-6 3184/4471 24362.8 80 10K-250A 10K-100A 16K-200A 2230 TCH-60-5 2985/4272 24306.5 75 10K-250A 10K-100A 16K-200A 2400 TCH-60-5 2985/4272 24258.9 75 10K-250A 10K-100A 16K-200A 2150 TCH-60-4 2786/4073 24217.8 70 10K-200A 10K-100A 16K-200A 2060 TCH-60-4 2786/4073 24182.4 70 10K-200A 10K-100A 16K-200A 2060
280 TCH-70-3 2363/3890 28423.3 95 10K-250A 10K-125A 16K-200A 2400 TCH-70-2 2239/3766 28357.6 90 10K-250A 10K-125A 16K-200A 2400 TCH-70-1 2114/3641 28302.1 85 10K-250A 10K-125A 16K-200A 2330 TCH-70-1 2114/3641 28254.1 85 10K-250A 10K-125A 16K-200A 2330 TCH-70-1 2114/3641 28212.8 85 10K-250A 10K-100A 16K-200A 2330
320 TCH-70-5 2612/4139 32483.8 105 10K-300A 10K-125A 16K-250A 2560 TCH-70-4 2487/4014 32408.7 100 10K-250A 10K-125A 16K-250A 2560 TCH-70-4 2487/4014 32345.2 100 10K-250A 10K-125A 16K-250A 2480 TCH-70-3 2363/3890 32290.4 95 10K-250A 10K-125A 16K-250A 2480 TCH-70-3 2363/3890 32243.2 95 10K-250A 10K-125A 16K-250A 2400
360 TCH-70-8 2985/4512 36544.3 120 10K-300A 10K-125A 16K-250A 2780 TCH-70-7 2860/4387 36459.8 115 10K-300A 10K-125A 16K-250A 2780 TCH-70-6 2736/4263 36388.4 110 10K-250A 10K-125A 16K-250A 2730 TCH-70-5 2612/4139 36326.7 105 10K-250A 10K-125A 16K-250A 2730 TCH-70-5 2612/4139 36273.6 105 10K-250A 10K-125A 16K-250A 2620
400 TCH-70-10 3233/4760 40604.7 130 10K-300A 10K-125A 16K-250A 2990 TCH-70-9 3109/4636 40510.8 125 10K-300A 10K-125A 16K-250A 2920 TCH-70-9 3109/4636 40431.5 125 10K-300A 10K-125A 16K-250A 2920 TCH-70-8 2985/4512 40363.1 120 10K-300A 10K-125A 16K-250A 2850 TCH-70-7 2860/4387 40304 115 10K-250A 10K-125A 16K-250A 2780
10
R&D Center
1219-1, Jisa-Dong, Gangseo-Gu, Busan, Korea TEL : +82-51-970-0711 FAX : +82-51-970-0730
Seoul Office
www.dh.co.kr
1575-6, Songjeong-Dong, Gangseo-Gu, Busan, 618-818, Korea TEL : +82-51-970-1000 FAX : +82-51-970-1001
Room No, 1515 Hanshin Core Officetel 11-9 No.2508 JiangShan Road Luchaogang Shinchun-Dong, Songpa-Gu,Seoul 138-733, Korea Shanghai 201308 P.R.China TEL : +82-2-421-4707 TEL : +86 (0)21-5197-5001 FAX : +86 (0)21-5197-5005 FAX : +82-2-421-4708
DH No. 200910