Escolar Documentos
Profissional Documentos
Cultura Documentos
T7/T67/T6C Series
Catalogue HY29-0001/UK
Content
General
SINGLE
T7AS
T7ASW
T7B - T7BS
T6C
T7D - T7DS
T7E - T7ES
DOUBLE
T7BB - T7BBS
T6CC
T67CB
T7DB - T7DBS
T67DC
T7DD - T7DDS
T7EB - T7EBS
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Content
T7/T67/T6C
T67EC
T7ED - T7EDS
T7EE - T7EES
TRIPLE
T7DBB - T7DBBS
T7DCB - T7DCBS
Dimensions ....................................................................................... 52
Ordering code and operating characteristics . ................................... 53
Technical data ................................................................................... 54
T7DCC - T7DCCS
T7DDB - T7DDBS
T67DDCS
Dimensions ....................................................................................... 60
Ordering code and operating characteristics . ................................... 61
Technical data ................................................................................... 62
T7EDB - T7EDBS
T67EDC - T67EDCS
Dimensions ....................................................................................... 66
Ordering code and operating characteristics . ................................... 67
Technical data ................................................................................... 68
T7EEC - T7EECS
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Characteristics
CHARACTERISTICS
These vane pumps have been specially designed for high/low circuits.
The combination of different cartridges in double and triple pumps
allows low flow at high pressure (300 bar max.) and high flow at lower
pressure. This is a clever way to optimize your circuit design.
This pump feature will also allow a very fast pressure cycle change
with a very precise flow repeatability.
GREATER FLOW
HIGHER PRESSURE
BETTER EFFICIENCY
MOUNTING FLEXIBILITY
CARTRIDGE DESIGN
Viscosities from 860 to 10 cSt permit colder starts and hotter running.
The balanced design compensates for wear and temperature changes.
At high viscosity or cold temperature, the rotor to side plates gap is
well lubricated and improves mechanical efficiency.
1. Check speed range, pressure, temperature, fluid quality, fluid viscosity and pump rotation.
2. Check inlet conditions of the pump, if it can accept the application
requirements.
3. Check the type of shaft : if it will support the operating torque.
4. Check the coupling must be chosen to minimize pump shaft load
(weight, misalignment).
5. Filtration : must be adequate for the lowest contamination level.
6. Check the environment of the pump : as to avoid noise reflection,
pollution and shocks.
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Single
pumps : speeds, pressure ratings
Model of
pump
Maximum Speed 3)
Theoretical
Minimum
Displacement
HF-0, HF-1 HF-3, HF-4
Speed
Series
Vi
HF-2
HF-5
ml/rev.
B06
T7AS2)
T7ASW2)
T7B
T7BS
T6C
T7/T67/T6C
RPM
Maximum Pressure
HF-0, HF-2
HF-3
Int.
Cont.
Int.
Cont.
Int.
Cont.
bar
bar
bar
bar
bar
bar
300
275
240
210
175
140
3000
275
240
3600
300
275
240
210
175
140
240
210
175
140
175
140
RPM
RPM
5,8
B10
9,8
B11
11,0
B13
12,8
B17
17.2
B20
19,8
B22
22,5
B25
24,9
B26
26,0
B28
28,0
B30
30,0
B32
31,8
B34
34,0
B36
36,0
B40
40,0
B02
5,8
B03
9,8
B04
12,8
B05
15,9
B06
19,8
B07
22,5
B08
24,9
B09
28,0
B10
31,8
B11
35,0
B12
41,0
B14
45,0
B15
50,0
003
10,8
005
17,2
006
21,3
008
26,4
010
34,1
012
37,1
014
46,0
017
58,3
020
63,8
022
70,3
025
79,3
028
88,8
031
100,0
600
3600
600
1800
1800
3000
280
240
3600
3201)
290
600
1800
3000
2800
600
300
275
280
240
275
240
1800
175
210
2500
210
160
160
HF-0, HF-2 = Antiwear Petroleum Base - HF-1 = Non Antiwear Petroleum Base - HF-3 = Water in oil Invert Emulsions
HF-4 = Water Glycols Solutions - HF-5 = Synthetic Fluids
Please consult Parker Denison for application over 300 bar.
Please be careful as these cartridge designation are now in ml/rev. (example : B22 = 22,5 ml/rev.)
3)
Please be sure that the inlet velocity is under 1,9 m/sec. (see page 12, start-up & check-up).
1)
2)
For further information, or if the performance characteristics outlined here above do not meet your particular requirements, please consult
your local Parker Denison office.
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Single
pumps : speeds, pressure ratings
Model of
Series
pump
Theoretical
Displacement
Vi
ml/rev.
T7D
T7DS
T7E 2)
T7ES
B14
44,0
B17
55,0
B20
66,0
B22
70,3
B24
81,1
B28
90,0
B31
99,2
B35
113,4
B38
120,6
B42
137,5
0451)
145,7
0501)
158,0
042
132,3
045
142,4
050
158,5
052
164,8
054
171,0
057
183,3
062
196,7
066
213,3
072
227,1
085
268,7
Maximum Speed 3)
Minimum
HF-0, HF-1 HF-3, HF-4
Speed
HF-2
HF-5
RPM
RPM
RPM
3000
Maximum Pressure
HF-0, HF-2
Int.
Cont.
Int.
Cont.
bar
bar
bar
bar
bar
bar
240
210
175
140
300
1800
2800
280
2500
260
230
240
210
210
160
240
210
210
175
175
140
90
75
75
75
75
75
2200
600
HF-3
Cont.
250
600
Int.
2200
1800
2000
210
175
160
For further information, or if the performance characteristics outlined here above do not meet your particular requirements, please consult
your local Parker Denison office.
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Double
& triple pumps : speeds, pressure ratings
Model of
pump
T7BB/S
T67CB
T7DB/S
T7EB/S
T7DBB/S
T7DCB/S
T7DDB/S
T7EDB/S
T6CC
T67CB
T67DC
T67EC
T7DCB/S
T7DCC/S
T67DDCS
T67EDC/S
T7EEC/S
T7DB/S
T67DC
T7DD/S
T7EDS
T7DBB/S
T7DCB/S
T7DCC/S
T7DDB/S
T67DDCS
T7EDB/S
T67EDC/S
T7EB/S
T67EC
T7EDS
T7EE/S
T7EEC/S
T67EDB/S
T67EDC/S
T7/T67/T6C
Maximum Speed 3)
Theoretical
Minimum
Displacement
HF-0,
HF-1 HF-3, HF-4
Speed
Series
Vi
HF-2
HF-5
B02
B03
B04
B05
B06
B07
B08
B09
B10
B11
B12
B14
B15
003
005
006
008
010
012
014
017
020
022
025
028
031
B14
B17
B20
B22
B24
B28
B31
B35
B38
B42
0451)
0501)
042
045
050
052
054
057
062
066
072
085
ml/rev.
5,8
9,8
12,8
15,9
19,8
22,5
24,9
28,0
31,8
35,0
41,0
45,0
50,0
10,8
17,2
21,3
26,4
34,1
37,1
46,0
58,3
63,8
70,3
79,3
88,8
100,0
44,0
55,0
66,0
70,3
81,1
90,0
99,2
113,4
120,6
137,5
145,7
158,0
132,3
142,4
158,5
164,8
171,0
183,3
196,7
213,3
227,1
268,7
RPM
600
600
RPM
22002)
22002)
RPM
1800
HF-0, HF-2
Int.
Cont.
bar
bar
T7BB
T7BBS
3201)
T7BB
T7BBS
290
Other
pumps
300
Other
pumps
275
280
240
275
240
1800
Maximum Pressure
HF-1, HF-4, HF-5
Int.
Cont.
bar
bar
240
210
Cont.
bar
175
140
175
140
175
140
175
210
210
HF-3
Int.
bar
160
160
300
250
600
2200
2)
240
210
1800
280
600
22002)
1800
2000
260
240
210
230
210
160
240
90
210
175
160
210
210
175
175
140
75
75
75
75
75
For further information or if the performance characteristics outlined above do not meet your particular requirements, please consult your
local Parker Denison office.
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Industrial Vane Pumps
Minimum
allowable inlet pressure (bar absolute) T7/T67/T6C
Minimum allowable inlet pressure (bar absolute)
Cartridge
Size
Series
Speed RPM
1200
1500
1800
2100
2200
2300
2500
2800
3000
3600
B06
B06
B10
0,80
B11
AS
B13
B17
0,80
0,80
0,80
0,80
0,80
0,80
0,80
0,80
B17
B20
0,94
B20
B22
1,00
B22
B25
0,85
B26
B28
0,80
B30
B32
0,80
0,80
0,80
0,80
0,80
0,80
0,80
0,80
B28
B30
B32
0,80
B34
0,88
B34
B36
0,94
B36
B40
1,00
B40
B02
B02
B03
0,80
B04
0,80
B05
B07
B08
0,80
0,80
0,80
0,80
0,80
0,80
0,80
0,80
B09
0,82
0,98
0,85
1,05
B10
1,15
B11
0,90
B12
0,84
B15
0,99
1,13
003
0,80
006
0,85
0,80
0,80
0,80
0,85
017
028
031
1,00
0,80
010
022
B07
B08
B09
B10
B11
B14
B15
0,85
0,90
0,85
005
0,90
0,80
008
020
B06
003
005
014
B04
B12
B14
012
B03
B05
B06
B11
B13
0,80
B26
B10
0,88
B25
ASW
Series
008
010
0,92
012
0,95
0,90
0,90
006
0,98
1,03
1,05
014
017
020
0,95
0,95
1,05
022
0,98
0,98
1,08
028
0,90
1,11
1,11
031
Inlet pressure is measured at inlet flange with petroleum base fluids at viscosity between 10 and 65 cSt. The difference between inlet pressure
at the pump flange and atmospheric pressure must not exceed 0,2 bar to prevent aeration.
Multiply absolute pressure by 1,25 for HF-3, HF-4 fluids.
by 1,35 for HF-5 fluid.
by 1,10 for ester or rapeseed base.
For double and triple pumps, prefer the cartridge requiring the highest absolute pressure.
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Minimum
allowable inlet pressure
T7/T67/T6C
Cartridge
Size
Series
Speed RPM
1200
1500
1800
2100
2200
2300
2500
B14
B17
B20
B22
0,80
B24
B28
B31
0,80
0,80
0,80
0,80
0,80
0,80
3600
Series
2800
3000
0,80
0,80
0,82
0,86
B20
0,83
0,88
B22
0,86
0,95
B24
0,88
1,00
B28
0,90
1,05
B31
B17
B35
0,84
0,97
B35
B38
0,86
1,01
B38
B42
0,90
045
0,85
050
B42
0,98
1,05
B45
1,02
1,09
B50
042
042
045
045
050
052
B14
0,80
0,80
050
0,90
0,80
052
1,00
054
054
057
0,85
062
066
072
085
0,85
0,85
0,90
0,90
0,95
0,85
057
0,95
1,00
062
1,09
066
1,05
072
085
1,00
Inlet pressure is measured at inlet flange with petroleum base fluids at viscosity between 10 and 65 cSt. The difference between inlet pressure
at the pump flange and atmospheric pressure must not exceed 0,2 bar to prevent aeration.
Multiply absolute pressure by 1,25 for HF-3, HF-4 fluids.
by 1,35 for HF-5 fluid.
by 1,10 for ester or rapeseed base.
For double and triple pumps, prefer the cartridge requiring the highest absolute pressure.
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Pump
selection
main calculation
To resolve
Volumetric displ.... Vi [ml/rev.]
Available flow........ qv [l/min]
Input power........... P [kW]
Performances required
Requested flow . ... qv [l/min] 75
Speed..................... n [RPM] 2500
Pressure................. p [bar]
250
Routine :
Example :
1. First calculation Vi =
1000 Q
n
Vi =
1000 x 75
= 30 ml/rev.
2500
qVi =
Pi =
31,8 x 2500
= 79,5 l/min
1000
79,5 x 250
= 33,1 kW
600
Vi = 31,8 ml/rev.
qVe = 76,5 l/min
P = 34,0 kW
9. Results
T7B B10
T7 and T67 units may be operated intermittently at pressures higher than the recommended
continuous rating when the time weighted average of pressure is less than or equal to
the continuous duty pressure rating. This intermittent pressure rating calculation is only
valid when the other parameters : speed, fluid, viscosity and contamination level are
respected.
For total cycle time longer than 15 minutes, please consult your Parker Denison representative.
Pressure (bar)
300
Average Pressure
211,5
200
Cycle
100
0
0
Time (minutes)
10
10
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Description
T7/T67/T6C
Outlet
Inlet
90 Section
Section A-A
Discharge ramp
where unloaded
vane moves in.
application advantages
The wide speed range (600 RPM at 3600 RPM), combined with
large size cartridge displacements will optimize operation for the
lowest noise level in the smallest envelope.
The low speed (600 RPM), low pressure, high viscosity (860 cSt)
allows application in cold environment with a minimum energy
consumption and without risk of seizure.
The low ripple pressure ( 2 bar) reduces piping noise and increases
lifetime of the other components in the circuit.
11
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
GENERAL :
All Parker Denison vane pumps are individually tested to provide the best
quality & reliability. Modifications, conversions & repairs can only be
done by authorized dealers or OEM to avoid invalidation of the guarantee.
The pumps are to be used in the design limits indicated in all the sales
bulletins. Please contact Parker Denison when tresspassing the catalogue
limits.
Do not modify or work on the pump under pressure or when the electric
motor (or any drive) is on.
Qualified personnel is required to assemble and set-up hydraulic devices.
Always conform yourself to the valid regulations (safety, electrical,
environment...).
The following instructions are important to follow to obtain a good service
life time from the unit.
The rotation and ports orientation are viewed from the shaft end.
CW stands for clockwise = right-hand rotation.
CCW stands for counter-clockwise = left-hand rotation.
Start-up check-up
Q (Lpm)
6 x p x r (cm)
2
= m/s
V=
Q (GPM)
3.12 x p x r2 (in)
= ft/s
The size of the air filter should be 3 times greater than the max. instant
return flow (all cylinders in movement for example).
If the pump is in the tank, please choose the NOP option (no paint) and
use a short inlet pipe.
Parker Denison does not recommend inlet strainers. If needed, a 100 mesh
(149 microns) is the finest mesh recommended.
A coaxial drive is recommended. For any other type of drives, please
contact Parker Denison.
Make sure that all protective plugs & covers have been removed.
Check the pump rotation versus the E-motor or engine rotation.
Start-up :
The tank has been filled up with a clean fluid in proper conditions.
We recommend to flush the system with an external pump prior to the
start-up.
It is important to bleed the air off the circuit & the pump itself.
The first valve on the circuit should be open to tank.
We recommend the use of air bleed off valves.
It is possible to bleed off the air by creating a leak in the P port of the
pump. Warning : this has to be done in a low pressure mode as it could
create a dangerous fluid leak. Make sure that the pressure cannot rise
(open center valve to tank, pressure relief valve unloaded ...).
12
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7/T67/T6C
When oil free of air appears, tighten the connectors to the correct torque.
The pump should prime within a few seconds. If not, please consult
our troubleshooting guide (document 1 - EN0721 - *).
If the pump is noisy, please troubleshoot the system.
Never operate the pump at top speed and pressure without checking
the completion of pump priming.
The mating female spline should be free to float and find its own
center. If both members are rigidly supported, they must be aligned
within 0,15 TIR (0.006 TIR) or less to reduce fretting. The angular alignment of two splines axes must be less than 0,05 per 25,4
radius ( 0.002 per 1 radius).
The coupling spline must be lubricated with a lithium molydisulfide grease, disulfide of molybdenum or a similar lubricant.
Parker Denison supplies the T7 series keyed shaft pumps with high
strength heat-treated keys. Therefore, when installing or replacing
these pumps, the heat-treated keys must be used in order to ensure
maximum life in the application. If the key is replaced, it must be a
heat-treated key between 27 and 34 R.C. hardness. The corners of the
keys must be chamfered by 0,76 mm to 1,02 mm (0.03 to 0.04) at 45
to clear the radii in the key way.
The alignment of keyed shafts must be within tolerances given for splined
shafts here above.
shaft loads
These products are primarily designed for coaxial drives which do not
impose axial or side loading on the shaft. Contact Parker Denison for
specific applications.
SPECIFIC POINTS :
MINIMUM INLET PRESSURE
Please read the charts in the sales leaflets as the minimum requested
inlet pressure varies versus the displacement and the speed.
Never go under 0,8 bar Absolute (-0,2 bar relative)
11.6 PSI Absolute (-2.9 PSI G).
VERTICAL MOUNT
FLUIDS :
Denison classification
Type of fluids : For each type of fluids, Parker Denisons vane pumps
will have different pressures, speeds & temperature limits. Please
refer to the sales leaflets.
HF-0 = Anti-wear petroleum base.
HF-1 = Non anti-wear petroleum base.
HF-2 = Anti-wear petroleum base.
HF-3 = Water-in-oil invert emulsions.
HF-4 = Water glycol solutions.
HF-5 = Synthetic fluids.
13
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Industrial Vane Pumps
Start-up
instructions & recommendations T7/T67/T6C
Filtration recommendations
recommended fluids
The use of fluids other than petroleum based antiwear R & O fluids
requires that the maximum ratings of the pumps will be reduced. In
some cases the minimum replenishment pressures must be increased.
Consult specific sections for more details.
viscosity
Indutrial
860 cSt - 3900 SUS
108 cSt - 500 SUS
30 cSt - 140 SUS
18 cSt -
90 SUS
10 cSt -
60 SUS
viscosity index
TEMPERATURES
C
+ 100
+ 50
+ 70
+ 65
F
+ 212
+ 122
+ 158
+ 149
- 18
+ 10
- 18
- 0.4
+ 50
- 0.4
N.m
kW
Lpm
rpm
N.m
kW
14
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
General characteristics
T7/T67/T6C
Mounting standard
Weight without
connector and
bracket - kg
Moment of
inertia
Kgm2 x 10-4
T7AS
SAE J744
ISO/3019-1 SAE A
9,5
2,6
T7ASW
SAE J744
ISO/3019-1 SAE A
11,3
3,2
23,0
3,2
1.1/2"
1" or 3/4"
15,7
7,5
1.1/2"
1"
26,0
19,6
2"
1.1/4"
43,3
62,5
3"
1.1/2"
T7B
T7BS
T6C
T7D
T7DS
T7E
T7ES
T7BB
T7BBS
T6CC
T67CB
T7DB
T7DBS
T67DC
T7DD
T7DDS
T7EB
T7EBS
T67EC
T7ED
T7EDS
T7EE
T7EES
ISO/3019-2
100 A2 HW
SAE J744
SAE B
SAE J744
SAE B
ISO 3019-2
125 A2 HW
SAE J744
SAE C
ISO 3019-2
125 A2 HW
SAE J744
SAE C
ISO 3019-2
100 A2 HW
SAE J744
SAE B
SAE J744
SAE B
SAE J744
SAE B
ISO 3019-2
125 A2 HW
SAE J744
SAE C
SAE J744
SAE C
SAE J744
SAE C
ISO 3019-2
125 A2 HW
ISO 3019-2
125 A2 HW
SAE J744
SAE C
SAE J744
SAE C
ISO 3019-2
125 A2 HW
SAE J744
SAE C
ISO 3019-2
250 B4 HW
SAE J744
SAE E
P1
P2
32,6
6,7
2.1/2"
1" or 3/4"
3/4"
26,0
16,9
2.1/2" or 3"
1"
1" or 3/4"
26,0
11,4
2.1/2"
1"
3/4"
38,6
22,7
3"
1.1/4"
1" or 3/4"
38,6
26,3
3"
1.1/4"
1" or 3/4"
56,0
36,3
4"
1.1/4"
1.1/4"
55,0
65,9
3.1/2"
1.1/2"
3/4"
55,0
70,8
3.1/2"
1.1/2"
1"
66,0
79,7
4"
1.1/2"
1.1/4"
95,0
97,4
4"
1.1/2"
1.1/2"
15
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
General
characteristics
Mounting standard
T7DBB
T7DBBS
T7DCB
T7DCBS
T7DCC
T7DCCS
T7DDB
T7DDBS
T67DDCS
T7EDB
T7EDBS
T67EDC
T67EDCS
T7EEC
T7EECS
ISO/3019-2
125 A2 HW
SAE J744
SAE C
ISO/3019-2
125 A2 HW
SAE J744
SAE C
ISO/3019-2
125 A2 HW
SAE J744
SAE C
ISO 3019-2
125 B4 HW
SAE J744
SAE C
SAE J744
SAE C
ISO 3019-2
250 B4 HW
SAE J744
SAE E
ISO 3019-2
250 B4 HW
SAE J744
SAE E
ISO/3019-2
250 B4 HW
SAE J744
SAE E
Weight without
connector and
bracket - kg
Moment of
inertia
Kgm2 x 10-4
Suction
S
P3
26,1
61,0
29,7
4"
1.1/4"
1"
1" or 3/4"
33,3
66,0
39,5
4"
1.1/4"
1.1/4"
1" or 3/4"
66,0
43,1
4"
1.1/4"
1.1/4"
1" or 3/4"
102,0
76,6
4"
1.1/2"
1.1/4"
1" or 3/4"
102,0
80,2
4"
1.1/2"
1.1/4"
1" or 3/4"
114,8
99,1
4"
1.1/2"
1.1/2"
1" or 3/4"
16
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Notes
T7/T67/T6C
17
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7AS
- Ordering Code
Model No.
T7AS - B17 - 1 R 00 - A 1 - 00 - ..
Modifications
Displacement *
Volumetric displacement (ml/rev.)
B06 = 5,8
B10 = 9,8
B11 = 11,0
B13 = 12,8
B17 = 17,2
B20 = 19,8
B22 = 22,5
B25 = 24,9
Type of shaft T7AS
1 = keyed (non SAE) 19,05
3 = splined 16/32 (SAE B) 13 teeth
4 = splined 16/32 (SAE A) 9 teeth
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
5 = S5 VITON - 0,7 bar max. (for mineral oil
and fire resistant fluids)
Design letter
S
P
00
01
02
03
24 cSt
10 cSt
5
4
3
2
1
0
0
60
120
180
240
300
P = Pressure
S = Suction
Porting combination
00 = standard
66
64
62
n = 1500 RPM
= 32 cSt
Lw = Lp + 8 db(A)
60
58
56
54
52
50
0
50
100
150
200
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Pressure p [bar]
300
1100
1,2
n = 1000 RPM
n = 1500 RPM [24 cSt]
900
0,8
Load F [N]
250
0,6
0,4
700
F
Fa
Shaft keyed N1
500
300
0,2
0
0
60
120
180
240
100
600
300
Pressure p [bar]
* Cartridge designation is now in ml/rev. (example : B22 = 22,5 ml/rev.)
1200
1800
2400
3000
Speed n [RPM]
Maximum permissible axial load Fa = 600 N
18
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
3600
Catalogue HY29-0001/UK
T7AS
- Dimensions - Weight : 9,5 kg
138,5
44,4
78,1
110
38,2
7,4
95,3
63,5
(THREADED PORT
CONNECTION)
KEY 4,775
4,724
0
-0.05
25,4
47
110
C.G.
1,5 x 45
82,55
68
(THREADED PORT
CONNECTION)
11
65
60,5
6,4
106
21,14 MAX
19,05
0,8 x 45
53
0
-0.025
64
SHAFT CODE 1
130,4
39,4
7,4
6,4
11,2
22,3
26,2
SHAFT CODE 4
SAE A spline d shaft
Class 1 - J498
16/32 d.p. - 9 teeth
30 pressure angle
flat root side fit
19,1
52,4
47,6
1,5 x 45
SHAFT CODE 3
SAE B splined shaft
Class 1 - J498
16/32 d.p. - 13 teeth
30 pressure angle
flat root side fit
PRESSURE B
Code
00
02
03
04
25,40
SAE # 16
1.5/16 - 12 UNF - 2B
1.1/14 NPTF
1 BSP
19,05
SAE # 12
1.1/16 - 12 UNF - 2B
3/4 NPTF
SUCTION A
3/4 BSP
Shaft
Vi x p max.
8720
8720
6550
Series
Vi Volumetric
displacement
T7AS
B06
B10
B11
B13
B17
B20
B22
B25
5,8 ml/rev
9,8 ml/rev
11,0 ml/rev
12,8 ml/rev
17,2 ml/rev
19,8 ml/rev
22,5 ml/rev
24,9 ml/rev
19
Catalogue HY29-0001/UK
T7ASW
- Ordering Code
Model No.
T7ASW - B32 - 1 R 00 - A 1 - 00 - ..
Modifications
Displacement *
Volumetric displacement (ml/rev.)
B26 = 26,0
B28 = 28,0
B30 = 30,0
B32 = 31,8
B34 = 34,0
B36 = 36,0
B40 = 40,0
Type of shaft T7ASW
1 = keyed (non SAE) 19,05
3 = splined 16/32 (SAE B) 13 teeth
4 = splined 16/32 (non SAE) 11 teeth
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
Design letter
Porting combination
00 = standard
S
P
P
00
01
02
03
Noise level (typical) - t7asW b28
8
24 cSt
10 cSt
6
5
4
3
2
1
0
0
60
120
180
240
300
P = Pressure
S = Suction
73
71
n = 1500 RPM
69
u = 32 cSt
67
Lw = Lp + 8 db(A)
65
63
61
59
57
0
50
100
150
200
250
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Pressure p [bar]
1,2
300
1100
n = 1000 RPM
n = 1500 RPM [24 cSt]
900
0,8
Load F [N]
0,6
0,4
700
F
Fa
Shaft keyed N1
500
300
0,2
0
0
60
120
180
240
100
600
300
Pressure p [bar]
* Cartridge designation is now in ml/rev. (example : B22 = 22,5 ml/rev.)
1200
1800
2400
3000
Speed n [RPM]
Maximum permissible axial load Fa = 800 N
20
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
3600
Catalogue HY29-0001/UK
160,8
110
44
38,2
99,7
95,3
63,5
(THREADED PORT
CONNECTION)
110
52,02
25,4
82,55
82,5
68
(THREADED PORT
CONNECTION)
11
65
60,5
7,4
6,4
1,5 x 45
53
MOUNTING TORQUE : 110 Nm
106
0
-0.025
19,05
0,8 x 45
21,12 MAXI
74,6
SHAFT CODE 1
130,4
(KEYED NO SAE)
40
37
7,4
22,3
11,2
30,2
7,4
19
24,5
58,7
47,6
1,5 x 45
1,5 x 45
SHAFT CODE 4
Splined shaft
Class 1 - J498b
16/32 d.p. - 11 teeth
30 pressure angle
flat root side fit
SHAFT CODE 3
PRESSURE B
Code
00
02
03
04
31,80
SAE # 20
1.5/16 - 12 UNF - 2B
1.1/14 NPTF
11/4 BSP
19,05
SAE # 12
1.1/16 - 12 UNF - 2B
SAE # 12
1.1/16 - 12 UNF - 2B
3/4 BSP
SUCTION A
Vi x p max.
18530
18530
12660
Series
Vi Volumetric
displacement
T7ASW
B26
B28
B30
B32
B34
B36
B40
26,0 ml/rev
28,0 ml/rev
30,0 ml/rev
31,8 ml/rev
34,0 ml/rev
36,0 ml/rev
40,0 ml/rev
21
Catalogue HY29-0001/UK
T7B
/ T7BS - Ordering Code
Model No.
Modifications
Mounting w/connection variables
4 bolts SAE flange J518
T7B-T7BS
Metric thread
M0
M1
1"
3/4"
1.1/2"
Displacement
Volumetric displacement (ml/rev.)
B02 = 5,8
B07 = 22,5 B11 = 35,0
B03 = 9,8
B08 = 24,9 B12 = 41,0
B04 = 12,8
B09 = 28,0 B14 = 45,0
B05 = 15,9
B10 = 31,8 B15 = 50,0
B06 = 19,8
T7BS
UNC thread
00
01
1"
3/4"
P
S
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 0,7 bar max. (for fire resistant fluids)
5 = S5 VITON - 0,7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Porting combination
00 = standard
00
01
02
PS
03
S
S
8
24 cSt
10 cSt
6
5
4
3
2
1
0
0
40
80
120
160
200
240
280
320
65
60
55
50
0
40
80
120
160
200
240
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Pressure p [bar]
1,4
320
1400
n = 1000 RPM
n = 1500 RPM [24 cSt]
1,2
1200
Load F [N]
280
0,8
0,6
0,4
1000
800
Shaft
=
keyed
Fn1
Fa
Shaft keyed N1
600
400
0,2
200
600
0
0
40
80
120
160
200
240
280
320
Pressure p [bar]
1200
1800
2400
3000
Speed n [RPM]
Maximum permissible axial load Fa = 800 N
22
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
3600
Catalogue HY29-0001/UK
T7B/BS - Dimensions
- Weight : 23,0 kg
168, 5
82,3
174,5
F
71,6
38,1
7,9
51,3
101,60
101,55
76,2
6,35 MAXI
1,3 x 45
T7BS SERIES
24,94 MAXI
1,5 x 45
120,6
22,225
22,200
C.G.
Shaft code 1
(KEYED SAE "B")
9,7
B 4- HOLES
40,7
7,9
24,5
70,0
35,8
17,9
24,5
1,5 x 45
12,7
A 4- HOLES
10
45,6
7,9
40,0
KEY 8 x 7
Shaft code 4
SAE BB INVOLUTE SPLINE DATA
CLASS 1 - FLAT ROOT SIDE FIT
J498b - PITCH 16/32
15 TEETH - 30 PRESSURE ANGLE
2,0 x 45
100,000
99, 967
28,22 MAXI
Shaft code 3
SAE B INVOLUTE SPLINE DATA
CLASS 1 - FLAT ROOT SIDE FIT
J498b - PITCH 16/32
13 TEETH - 30 PRESSURE ANGLE
1,5 x 45
25,0650
24,9935
35,0
70,0
1,5 x 45
Shaft code 2
(KEYED ISO R775)
Model
Code
A
B
C
D
E
F
G
H
T7B
T7BS
M0
M1
M10 x 19 deep
M12 x 22,4 deep
26,20
22,25
52,4
47,65
25,4
19,1
140
70
14,0
00
01
3/8"-16 UNC x 19 deep
1/2"-13 UNC x 22,4 deep
26,20
22,25
52,4
47,65
25,4
19,1
146
73
14,3
SUCTION 38,1
9,0
PRESSURE E
T7B SERIES
Series
Vi Volumetric
displacement
B02
5,8 ml/rev
B03
9,8 ml/rev
B04
12,8 ml/rev
B05
15,9 ml/rev
B06
19,8 ml/rev
B07
22,5 ml/rev
T7B
B08
24,9 ml/rev
T7BS
B09
28,0 ml/rev
B10
31,8 ml/rev
B11
35,0 ml/rev
B12
41,0 ml/rev
B14
45,0 ml/rev
B15
50,0 ml/rev
1) B11 - B12 - B14 = 300 bar max. int.
23
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T6C
- Ordering Code
Model No.
T6C* - 022 - 1 R 00 - B 1 - ..
Modifications
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and fire
resistant fluids)
Displacement
Volumetric displacement (ml/rev.)
003 = 10,8
017 = 58,3
005 = 17,2
020 = 63,8
006 = 21,3
022 = 70,3
008 = 26,4
025 = 79,3
010 = 34,1
028 = 88,8
012 = 37,1
031 = 100,0
014 = 46,0
Design letter
Porting combination
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Type of shaft
1 = keyed (SAE B) 22,2
2 = keyed (non SAE)
3 = splined (SAE B) 13 teeth
4 = splined (SAE BB) 15 teeth
00
01
02
PS
03
P = Pressure port
S = Suction port
S
S
21
24 cSt
18
10 cSt
15
12
9
6
3
0
0
35
70
105
140
175
210
245
280
70
65
60
55
0
40
80
120
160
200
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Pressure p [bar]
3,5
2,5
1200
Load F [N]
1400
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2800 RPM
240
2
1,5
1
1000
800
Shaft
Fkeyed
n1 Fa
Shaft keyed N1
600
400
0,5
200
600
0
0
40
80
120
160
200
240
280
Pressure p [bar]
1000
1400
1800
2200
2600
Speed n [RPM]
Maximum permissible axial load Fa = 800 N
24
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T6C
- Dimensions - Weight : 15,7 kg
174,5
161,6
146,0
82,3
71,4
38,1
73,0
38,1
9,7
7,9
6,35 MAXI
51,3
101,60
101,55
76,2
KEY 6.35
6.30
1,3 x 45
24,94 MAXI
1,5 x 45
14,3
22,225
22,200
75,7
M8 16 DEEP
135,0
C.G.
SHAFT CODE 1
(Keyed SAE B)
2)
12,7
35,8
45,5
17,9
7,9
7,9
26,2
13,1
24,5
24,5
31,7
1,5 x 45
52,4
P
1,5 x 45
22,225
22,200
35,0
SAE B INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 16/32
13 TEETH - 30 PRESSURE ANGLE
26,2
70,0
SHAFT CODE 2
SHAFT CODE 3
SHAFT CODE 4
SAE BB INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 16/32
15 TEETH - 30 PRESSURE ANGLE
SUCTION 38,1
PRESSURE 25,4
KEY 4,762
4,712
24,53 MAXI
1,5 x 45
Pressure
port
58,2
7,9
Vi Volumetric
displacement
003
10,8 ml/rev
005
17,2 ml/rev
006
21,3 ml/rev
008
26,4 ml/rev
010
34,1 ml/rev
012
37,1 ml/rev
T6C
014
46,0 ml/rev
017
58,3 ml/rev
020
63,8 ml/rev
022
70,3 ml/rev
025
79,3 ml/rev
028
88,8 ml/rev
031
100,0 ml/rev
1) 028 - 031 = 210 bar max. int.
2) Port connection can be supplied with metric threads (Please contact Parker Denison).
25
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7D
/ T7DS - Ordering Code
Model No.
Modifications
Mounting w/connection variables
4 bolts SAE flange J518
P = 1.1/4" - S = 2"
Metric thread
UNC thread
T7D
M0
T7DS
M0
Y01)
00
1)
250 bar max. int.
Displacement
Volumetric displacement (ml/rev.)
B14 = 44,0
B31 = 99,2
B17 = 55,0
B35 = 113,4
B20 = 66,0
B38 = 120,6
B22 = 70,3
B42 = 137,5
B24 = 81,1
045 = 145,7
B28 = 90,0
050 = 158,0
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Porting combination
00 = standard
00
01
02
PS
03
P = Pressure port
S = Suction port
S
S
30
27
24 cSt
24
10 cSt
21
18
15
12
9
6
3
0
0
50
100
150
200
250
300
n = 1000 RPM
Srie
1n = 1500 RPM
70
u = 32 cSt
Lw = Lp + 8 db (A)
65
60
55
0
40
80
120
160
200
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Pressure p [bar]
3,5
1600
1400
2,5
Load F [N]
280
1800
n = 1000 RPM
240
2
1,5
1
1200
1000
Shaft
keyed
=
=
n1
Fa
Shaft keyed N1
800
600
400
0,5
200
600
0
0
50
100
150
200
250
300
Pressure p [bar]
900
1200
1500
1800
2100
Speed n [RPM]
Maximum permissible axial load Fa = 1200 N
26
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2400
212,4
38,1
7,9
6,35 MA XI
T7DS
83,6
49,3
82, 6
12,7
64, 3
127, 00
126, 95
156, 7
M10 x 20 DEEP
76,2
2,3 x 45
SHAFT CODE 4
S A E C S pc (* ) I N VOL U T E S P LI N E D ATA
C L A SS 1 -FL AT ROOT SIDE FI T
J498 b - PI T C H 12/24
14 T EET H - 30 P R ES S UR E A N G L E
SHAFT CODE 2
2,3 x 45
SHAFT CODE 5
SU CTION 50,8 *
PRESSURE 31,8
38,0
2,3 x 45
SHAF T CODE 3
KE Y 10 x 8
M10 x 20 DEEP
55,2
7,9
50,0
15,1
21,45
77, 8
38, 9
31, 75
31, 70
2,3 x 45
42,9
64, 3
125, 000
124, 937
KEY 7,94
7 ,89
(Key ed SAE C)
35, 3 M A XI
38,1
B x 22 ,3 DEEP
SHAFT CODE 1
32, 018
32, 002
7,9
48,0
A x 23,9 DEEP
35,3 M AXI
7,9
73,2
58, 7
29, 35
77,7 (*)
87,4
9,0
6,35 MAXI
15,7
30,2
31, 75
31, 70
C.G.
2,3 x 45
147,4
KE Y 7,94
7,89
35, 3 MAXI
Catalogue HY29-0001/UK
T7D/DS Dimensions - Weight : 26,0 kg
Model
Code
A
B
C
D
E
1)
T7D
M0
M12
M12
180,0
90,0
18,0
00
1/2" - 13 UNC
7/16" - 14 UNC
T7DS
M0
M12
M12
181,0
90,5
17,5
YO1)
M12
M10
(ISO 3019/2- G 32 M)
7,9
T7D
Series
Vi Volumetric
displacement
27
4)
Catalogue HY29-0001/UK
T7E /
T7ES - Ordering Code
Model No.
Modifications
Mounting w/connection variables
4 bolts SAE flange J518
Displacement
Volumetric displacement (ml/rev.)
042 = 132,3 057 = 183,3
045 = 142,4 062 = 196,7
050 = 158,5 066 = 213,3
052 = 164,8 072 = 227,1
054 = 171,0 085 = 268,7
T7E - T7ES
T7ES
Metric thread
UNC thread
M0
00
1.1/2"
3"
P
S
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Porting combination
00 = standard
00
01
02
PS
03
P = Pressure port
S = Suction port
S
S
33
24 cSt
30
10 cSt
27
24
21
18
15
12
9
6
3
0
0
30
60
90
120
150
180
210
240
n = 1000 RPM
Srie
1n = 1500 RPM
75
= 32 cSt
Lw = Lp + 8 db (A)
70
65
60
0
40
80
120
160
200
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Pressure p [bar]
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
3200
2800
Load F [N]
3
2
1
2400
2000
240
Shaft
=
=
keyed
Fa
Shaft keyed N1
1600
1200
800
0
0
30
60
90
120
150
180
210
400
600
240
Pressure p [bar]
1000
1400
1800
Speed n [RPM]
Maximum permissible axial load Fa = 2000 N
28
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T7E/ES - Dimensions
- Weight : 43,3 kg
MOUNTING TORQUE 187 Nm
213,0
K
K/2
225,3
110,0
90,9
52,3
7,9
6,35 MAXI
147.60
T7ES
50,8
KEY 9,52
9,47
C.G.
76,2
38,10
38,05
42,36 MAXI
187,5
98,6
M10 x 20 DEEP
2,3 x 45
101,8
SHAFT CODE 1
e x 45
61,9
61,9
62,2
17,5
35,7
31,0
7,9
31,5
10,0
W
90,0
17,8
T7E
50,0
KEY 10 x 8
38,1
KEY 7.94
7.89
69,8
38,018
38,002
34,9
53,2
106,4
31,75
31,70
35,27 MAX
41,3 MAXI
M10 x 20 DEEP
2,3 x 45
2,3 x 45
2,3 x 45
SHAFT CODE 4
SAE CC INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 12/24
17 TEETH - 30 PRESSURE ANGLE
e x 45
SHAFT CODE 2
SHAFT CODE 5
( Keyed no SAE )
PRESSURE 37,10
55,9
7,9
38,0
2,3 x 45
SHAFT CODE 3
SAE C INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 12/24
14 TEETH - 30 PRESSURE ANGLE
T7E
T7ES
Max.
125,000
127,000
Min.
124,937
126,950
e x 45
Dia d
2,0
1,3
9,5
12,7
180,0
181,0
18,0
17,5
Series
Vi Volumetric
displacement
042
132,3 ml/rev
045
142,4 ml/rev
050
158,5 ml/rev
052
164,8 ml/rev
054
171,0 ml/rev
T7E
T7ES
057
183,3 ml/rev
062
196,7 ml/rev
066
213,3 ml/rev
072
227,1 ml/rev
085
268,7 ml/rev
1)
085 = 90 bar max. int.
* special 3"1/2 ( 88,9) suction also available - Please contact Parker Denison
29
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7BB
/ T7BBS - Ordering Code
Model No.
Modifications
P1
P2
Displacement P1 & P2
Volumetric displacement (ml/rev.)
B02 = 5,8
B09 = 28,0
B03 = 9,8
B10 = 31,8
B04 = 12,8
B11 = 35,0
B05 = 15,9
B12 = 41,0
B06 = 19,8
B14 = 45,0
B07 = 22,5
B15 = 50,0
B08 = 24,9
P1
P2
S
8
24 cSt
10 cSt
P1-P2
5
4
P1-P2
3
2
1
0
40
80
120
160
200
240
280
320
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
70
Pe = 0,9 bar abs
nSrie
= 1000 RPM
n1 = 1500 RPM
= 32 cSt
u
Lw = Lp + 8 db (A)
65
60
55
0
40
80
120
160
200
240
280
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2800 RPM
P1-P2
1200
Load F [N]
2
1,5
P1-P2
1
P1-P2
0,5
1000
800
=Shaft
=
keyed
F n1
Fa
Shaft keyed N1
600
400
0
0
50
100
150
200
250
320
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
2,5
3/4"
2.1/2"
Design letter
T7BBS
UNC thread
00
01
1"
3/4"
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 0,7 bar max. (for fire resistant fluids)
5 = S5 VITON - 0,7 bar max. (for mineral oil and
fire resistant fluids)
T7BB- T7BBS
Metric thread
M0
M1
1"
3/4"
200
600
300
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
1000
1400
1800
2200
2600
Speed n [RPM]
Maximum permissible axial load Fa = 800 N
30
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Industrial Vane Pumps
T7BB/BBS - Dimensions
- Weight : 32,6 kg T7/T67/T6C
262,4
T7BBS
58,2
101,6
38,1
6,4 MAXI
7,9
7,9
31,7
KEY 4,762
4,712
SHAFT CODE 3
28,22 MAXI
51,3
116,1
SHAFT CODE 2
1,3 x 45
B 4-HOLES
A 4-HOLES
T7BB
A 4-HOLES
50,8
22,2
SHAFT CODE 1
(KEYED NON SAE )
9,7
MOUNTING TORQUE : 61 Nm
22,225
22,200
24,53 MAXI
1,5 x 45
74,0
25,40
1,5 x 45
25,37
C.G.
101,60
M8 x 16 DEEP
76,2
1,5 x 45
84,1
74,7
38,1
24,5
101,55
71,4
40,7
7,9
98,6
KEY 6,35
6,30
12,7
70,0
10,0
40,0
KEY 8 x 7
25,4
PRESSURE 19
2,0 x 45
SUCTION 63.5
PRESSURE E
28,2 MAXI
44,5
G
1,5 x 45
25,0065
24,9935
P1
88,9
47,6
174,5
P2
100,000
99,967
SHAFT CODE 5
(KEYED ISO R775)
9,0
45,6
7,9
24,5
1,5 x 45
SHAFT CODE 4
SAE B-B INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 16/32
15 TEETH - 30 PRESSURE ANGLE
Model
Code
A
B
C
D
E
F
G
H
T7BB
M0
M1
M10 x 19 deep
M12 x 22,4 deep
26,20
22,25
52,4
47,65
25,4
19,1
140
70
14,0
T7BBS
00
01
3/8"-16 UNC x 19 deep
1/2"-13 UNC x 22,4 deep
26,20
22,25
52,4
47,65
25,4
19,1
146
73
14,3
Series
Vi Volumetric
displacement
B02
5,8 ml/rev
B03
9,8 ml/rev
B04
12,8 ml/rev
B05
15,9 ml/rev
B06
19,8 ml/rev
P1
B07
22,5 ml/rev
&
B08
24,9 ml/rev
B09
28,0 ml/rev
P2
B10
31,8 ml/rev
B11
35,0 ml/rev
B12
41,0 ml/rev
B14
45,0 ml/rev
B15
50,0 ml/rev
1) B11 - B12 - B14 = 300 bar max. int.
31
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T6CC
- Ordering Code
Model No.
P1
Modifications
P2
P2
P1 = 1" - S = 3"
UNC thread
Metric thread
00
01
0M
W0
1"
3/4"1)
1"
3/4
P2
P1 = 1" - S = 2.1/2"2)
UNC thread
Metric thread
10
11
1M
W1
1"
3/4"1)
1"
3/4
up to 46 ml/rev. max.
up to 126 ml/rev. max.
Always select the largest cartridge in the front place.
1)
2)
Type of shaft
Severe duty shaft (T6CCW only)
1 = keyed (non SAE) 2 = keyed (SAE BB)
3 = splined (SAE BB) 15 teeth
5 = splined (SAE B) 13 teeth
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and fire
resistant fluids)
Design letter
Porting combination (see page 72)
00 = standard
21
24 cSt
18
10 cSt
P1-P2
15
12
P1-P2
9
6
3
0
0
35
70
105
140
175
210
245
280
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
n = 1000 RPM
Srie1
n = 1500 RPM
Srie2
70
= 32 cSt
Lw = Lp + 8 db (A)
65
60
55
0
40
80
120
160
200
240
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
1400
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2800 RPM
1200
P1-P2
P1-P2
1
1000
800
Shaft
F n1
keyed
P1-P2
Load F [N]
75
Fa
Shaft keyed N1
600
400
0
0
40
80
120
160
200
240
200
600
280
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
1000
1400
1800
2200
2600
Speed n [RPM]
Maximum permissible axial load Fa = 800 N
32
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T6CC
- Dimensions - Weight : 26,0 kg
265,6
88,2
174,5
146,0
71,4
101,6
38,1
7,9
73,0
9,7
38,1
6,4 MAXI
28,2 MAXI
T6CCW
SHAFT CODE 2
7,9
K-4 HOLES 2)
E-4 HOLES 2)
40,7
45,5
7,9
101,60
51,3
1,3 x 45
25,40
1,5 x 45
25,37
126,0
73,2
14,3
C.G.
101,55
M8 x 16 DEEP
76,2
84,1
KEY 6,35
6,30
E-4 HOLES
24,5
2)
7,9
26,2
58,2
31,7
13,1
24,5
1,5 x 45
KEY 4,762
4,712
26,2
1,5 x 45
SHAFT CODE 1
24,5 MAXI
SHAFT CODE 5
SAE B INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 16/32
13 TEETH - 30 PRESSURE ANGLE
P1
22,225
22,200
SHAFT CODE 3
SAE BB INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 16/32
15 TEETH - 30 PRESSURE ANGLE
P2
52,4
1,5 x 45
( Keyed
o
non SAE )
PRESSURE C
SUCTION H
PRESSURE 25,4
Alternate ports
S = 3"
Code
A
B
C
D
E
F
G
H
K
1)
00
01
52,4
47,7
26,2
22,4
25,4
19,0
74,7
76,2
3/8"-16 UNC x 19 deep
106,4
61,9
76,2
5/8"-11UNC x 28,4 deep
1)
2)
0M
W0
52,4
47,7
26,2
22,4
25,4
19,0
74,7
76,2
M10 x 19 deep
1)
S = 2.1/2"2)
10
11
1M
W11)
52,4
47,7
52,4
47,7
26,2
22,4
26,2
22,4
25,4
19,0
25,4
19,0
74,7
76,2
74,7
76,2
3/8"-16 UNC x 19 deep
M10 x 19 deep
88,9
50,9
63,5
1/2"-13 UNC x 23,9 deep
M12 x 23,9 deep
1)
Series
Vi Volumetric
displacement
33
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T67CB
- Ordering Code
Model No.
P1
Modifications
P2
Displacement P1
Volumetric displacement (ml/rev.)
003 = 10,8
017 = 58,3
005 = 17,2
020 = 63,8
006 = 21,3
022 = 70,3
008 = 26,4
025 = 79,3
010 = 34,1
028 = 88,8
012 = 37,1
031 = 100,0
014 = 46,0
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Displacement P2
Volumetric displacement (ml/rev.)
B02 = 5,8
B09 = 28,0
B03 = 9,8
B10 = 31,8
B04 = 12,8
B11 = 35,0
B05 = 15,9
B12 = 41,0
B06 = 19,8
B14 = 45,0
B07 = 22,5
B15 = 50,0
B08 = 24,9
Type of shaft
Severe duty shaft (T67CW only)
1 = keyed (non SAE) 2 = keyed (SAE BB)
3 = splined (SAE BB) 15 teeth
5 = splined (SAE B) 13 teeth
22
20
24 cSt
18
10 cSt
16
P1
14
12
10
P1
P2
P2
4
2
0
0
50
100
150
200
250
300
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
5
P1
0
80
3,5
3
2,5
2
1,5
1
0,5
0
120
160
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2800 RPM
200
240
280
P2
P2
50
100
60
55
0
40
80
120
160
200
240
150
200
1000
800
= Shaft
=
keyed
F n1
Fa
Shaft keyed N1
600
400
P2
65
1200
P1
1
40
70
P1
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
Load F [N]
75
1400
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2800 RPM
250
200
600
300
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operaring conditions.
1000
1400
1800
2200
2600
Speed n [RPM]
Maximum permissible axial load Fa = 800 N
34
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T67CB
- Dimensions - Weight : 26,0 kg
174,5
146,0
265,6
88,2
71,4
101,6
38,1
7,9
6,4 MAXI
9,7
38,1
KEY 6,35
6,30
MOUNTING TORQUE : 61 Nm
1/2-13 UNC x 23,9 DEEP - 4 HOLES
(M12 x 30,0 DEEP - METRIC VERSION)
3/8-16 UNC x 19 DEEP - 4 HOLES
(M10 x 19 DEEP - METRIC VERSION)
26,2
13,1
40,7
7,9
58,2
7,9
31,7
24,5
24,5
KEY 4,762
4,712
1,5 x 45
SHAF T CODE 1
SHAFT CODE 5
SHAFT CODE 3
24,53 MAX
P1
22,225
26,2
47,7
P2
52,4
1,5 x 45
1,5 x 45
25,40
22,200
45,5
22,2
88
, 9
7,9
T67CBW
SHAFT CODE 2
1,5 x 45
25,37
1,5 x 45
28,22 MAXI
126,0
73,2
14,3
C.G.
101,60
51,3
M8 x 16 DEEP
101,55
76,2
84,1
76,2
73,0
(Keyed no SAE)
PRESSURE 19
SUCTION 63.5
PRESSURE 25,4
Shaft
1
2
Series
Vi Volumetric
displacement
35
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7DB/T7DBS - Ordering
Code
Model No.
Modifications
P1
P2
Displacement P1
Volumetric displacement (ml/rev.)
B14 = 44,0
B31 = 99,2
B17 = 55,0
B35 = 113,4
B20 = 66,0
B38 = 120,6
B22 = 70,3
B42 = 137,5
B24 = 81,1
045 = 145,7
B28 = 90,0
050 = 158,0
P1
P2
S
Design letter
Porting combination (see page 72)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
22
18
10 cSt
P1
16
14
12
10
P1
P2
P2
4
2
0
0
50
100
150
200
250
300
6
5
4
3
2
1
0
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
3,5
3
2,5
2
1,5
1
0,5
0
60
90
120
150
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
100
180
210
240
P2
150
60
55
0
40
80
120
160
200
240
200
Shaft
=
=
keyed
1600
1400
1200
Fa
Shaft keyed N1
1000
800
600
P2
50
65
1800
P2
70
2000
P1
P1
30
P1
75
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
Load F [N]
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
24 cSt
UNC thread
T7DBS
00
01
1.1/4"
1.1/4"
1"
3/4"
3"
3"
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Displacement P2
Volumetric displacement (ml/rev.)
B02 = 5,8
B09 = 28,0
B03 = 9,8
B10 = 31,8
B04 = 12,8
B11 = 35,0
B05 = 15,9
B12 = 41,0
B06 = 19,8
B14 = 45,0
B07 = 22,5
B15 = 50,0
B08 = 24,9
20
Metric thread
T7DB - T7DBS
M0
M1
1.1/4"
1.1/4"
1"
3/4"
3"
3"
250
400
600
300
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
900
1200
1500
1800
2100
Speed n [RPM]
Maximum permissible axial load Fa = 1200 N
36
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2400
Catalogue HY29-0001/UK
Industrial Vane Pumps
T7DB/DBS Dimensions - Weight : 38,6 kg T7/T67/T6C
212,40
109,50
KEY 7,94
7,89
31,75
73,2
62,0
38,1
48,02
2,3 x 45
( Keyed SAE C )
30,2
77,7
7,9
38,0
7,9
KEY 7,94
7,89
P1
SHAFT CODE 4
PRESSURE C
Dia d
9,5
12,7
180,0
181,0
18,0
17,5
PRESSURE 31,8
SUCTION 76
35,27 MAXI
58,7
31,75
M10 x 20 DEEP
32,018
32,002
35,0 MAXI
P2
106,4
2,3 x 45
2,3 x 45
SHAFT CODE 3
64,30
15,7
7/16 14 UNC 22.3 DEEP - 4 HOLES
M12 x 22.3 DEEP - METRIC VERSION
SHAFT CODE 1
31,70
55,2
KEY 10 x 8
e x 45
31,70
2,30 x 45
35,27 MAXI
129,5
7,9
50,0
SHAFT CODE 5
49,30
P1
74,05
87,9
83,60
M10 x 20 DEEP
2,3 x 45
C.G.
7,9
38,10
6,35 MAXI
7,90
88,90
74,70
DIA d
114,30
P2
82,60
K/2
286,00
SHAFT CODE 2
( Keyed non SAE )
Shaft
1
2
3
Pressure
port
1)
Series
Vi Volumetric
displacement
37
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T67DC
- Ordering Code
Model No.
Modifications
P1
P2
P1
P2
S
Design letter
Porting combination (see page 72)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Type of shaft
1 = keyed (SAE C)
3 = splined (SAE C) 14 teeth
2 = keyed (non SAE)
4 = splined (spec. SAE C)
Type of shaft - Severe duty (T67DCW only)
5 = keyed (non SAE)
22
18
10 cSt
P1
P2
16
14
12
P1
10
8
P2
6
4
2
0
0
35
70
105
140
175
210
245
280
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
6
P1
0
60
90
120
150
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
3
2
180
210
240
P2
120
160
1400
1200
40
80
120
160
200
240
Shaft
=keyed
=
Fa
Shaft keyed N1
1000
400
600
0
80
600
P2
1
40
60
800
P2
65
1600
1
30
70
1800
P1
75
P1
Pressure p [bar]
Double pump noise level is given with both stages section discharging at the pressure value indicated on the curve.
Load F [N]
80
2000
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
UNC thread
00
01
1.1/4"
1.1/4"
1"
3/4"
3"
3"
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Displacement P2
Volumetric displacement (ml/rev.)
003 = 10,8
017 = 58,3
005 = 17,2
020 = 63,8
006 = 21,3
022 = 70,3
008 = 26,4
025 = 79,3
010 = 34,1
028 = 88,8
012 = 37,1
031 = 100,0
014 = 46,0
20
Metric thread
M0
M1
1.1/4"
1.1/4"
1"
3/4"
3"
3"
200
240
280
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
900
1200
1500
Speed n [RPM]
1800
2100
38
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2400
Catalogue HY29-0001/UK
T67DC
- Dimensions - Weight : 38,6 kg
90,50
212,40
181,00
109,50
114,30
38,10
7,90
6,35 MAXI
83,60
12,66
49,30
2,30 x 45
1,30 x 45
SHAFT CODE 1
MOUNTING TORQUE : 68 Nm
31,75
31,70
35,27 MAXI
128,3
74,05
17,50
C.G.
127,00
64,30
M10 x 20 DEEP
126,95
82,60
88,90
74,70
KEY 7,94
7,89
7,90
T67DCW
SHAFT CODE 3
P2
P1
2,30 x 45
SHAFT CODE 2
SHAFT CODE 4
SUCTION 76
PRESSURE C
35,27 MAXI
38,42 MAXI
34,900
B
( Keyed no SAE )
34,875
M8 16 DEEP
SHAFT CODE 5
KEY 7,94
7,89
2,30 x 45
2,30 x 45
29,35
KEY 7,94
7,89
38,10
48,00
31,75
38,00
77,70
31,70
55,20
7,90
58,70
2,30 x 45
106,40
53,20
83,40
60,00
7,90
Shaft
1
2
3
PRESSURE 31,8
( Keyed no SAE )
Series
Vi Volumetric
displacement
39
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7DD
/ T7DDS - Ordering Code
Model No.
Modifications
P1
P2
Displacement P1 & P2
Volumetric displacement (ml/rev.)
B14 = 44,0
B31 = 99,2
B17 = 55,0
B35 = 113,4
B20 = 66,0
B38 = 120,6
B22 = 70,3
B42 = 137,5
B24 = 81,1
045 = 145,7
B28 = 90,0
050 = 158,0
Type
T7DD
T7DDS
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Type of shaft
1 = keyed (SAE C)
3 = splined (SAE C) 14 teeth
2 = keyed (SAE CC)
4 = splined (SAE BB)
Type of shaft - T7DD and T7DDS
5 = keyed (ISO 3019-2 - G32M)
Design letter
Porting combination (see page 72)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
22
20
24 cSt
18
10 cSt
P1-P2
16
14
12
10
P1-P2
8
6
4
2
0
0
30
60
90
120
150
180
210
240
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
75
70
65
60
0
40
80
120
160
200
240
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
6
n = 1000 RPM
5
1800
4
3
P1-P2
2
1
P1-P2
30
60
90
120
150
180
Fa
Shaft keyed N1
1400
1200
1000
800
600
0
0
= Shaft
=
keyed
1600
P1-P2
n = 2500 RPM
Load F [N]
80
210
400
600
240
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operaring conditions.
900
1200
1500
1800
2100
Speed n [RPM]
Maximum permissible axial load Fa = 1200 N
40
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2400
Catalogue HY29-0001/UK
Industrial Vane Pumps
T7DD/DDS Dimensions - Weight : 56 kg T7/T67/T6C
347,7
134,2
84,0
148,3
38,3
7,9
P2
P1
49,3
Key 7,94
7,89
2,3 x 45
e x 45
K2
K1
213,0
91,0
30,2
77,8
2,3 x 45
130,2
58,7
58,7
162,2
M10 x 20 DEEP
38,10
38,05
42,36 MAXI
182,0
P2
P1
SHAFT CODE 3
68,0
10,0
50,0
38,0
2,3 x 45
Keyed SAE CC
56,0
7,9
30,2
KEY 9,52
9,47
SHAFT CODE 2
64,3
SHAFT CODE 1
Keyed SAE C
7/16-14UNC x 24 DEEP
M12 x 24 DEEP-METRIC VERSION
50,8
19,0
5/8-11UNC x 30 DEEP
M16 x 30 DEEP-METRIC VERSION
7,9
M10 x 20 DEEP
91,3
170,9
31,75
31,70
K2
C.G.
35,27 MAXI
d1
101,6
114,9
d2
101,6
6,4 MAXI
PRESSURE 29,5
7,9
24,5
SUCTION 101,6
PRESSURE 31,8
KEY 10 x 8
SHAFT CODE 5
M10 x 20 DEEP
32,018
32,002
35,00 MAXI
1,5 x 45
SHAFT CODE 4
Dia S
Max.
Min.
125,000 124,937
127,000 126,950
e x 45
K1
Dia d1
K2
Dia d2
2,0
1,3
9,5
12,7
180,0
181,0
18,0
17,5
113,14
114,50
14,0
14,3
Shaft
1
2
3
1)
Series
Vi Volumetric
displacement
B14
44,0 ml/rev
B17
55,0 ml/rev
B20
66,0 ml/rev
B22
70,3 ml/rev
P1
B24
81,1 ml/rev
B28
90,0 ml/rev
&
B31
99,2 ml/rev
B35
113,4 ml/rev
P2
B38
120,6 ml/rev
B42
137,5 ml/rev
045
145,7 ml/rev
050
158,0 ml/rev
050 = 210 bar max. int.
41
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7EB/T7EBS - Ordering
Code
Model No.
Modifications
P1
P2
Displacement P1
Volumetric displacement (ml/rev.)
042 = 132,3 057 = 183,3
045 = 142,4 062 = 196,7
050 = 158,5 066 = 213,3
052 = 164,8 072 = 227,1
054 = 171,0 085 = 268,7
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Displacement P2
Volumetric displacement (ml/rev.)
B02 = 5,8
B09 = 28,0
B03 = 9,8
B10 = 31,8
B04 = 12,8
B11 = 35,0
B05 = 15,9
B12 = 41,0
B06 = 19,8
B14 = 45,0
B07 = 22,5
B15 = 50,0
B08 = 24,9
Design letter
Porting combination (see page 72)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
33
30
24 cSt
27
10 cSt
24
P1
21
18
P1
15
12
9
P2
6
3
P2
0
0
50
100
150
200
250
300
7
6
5
4
3
2
1
0
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
60
90
120
150
180
210
240
P2
1
0,5
0
100
150
60
0
40
80
120
160
200
240
200
1400
1200
Shaft
=
keyed
F
Fa
Shaft keyed N1
1000
800
600
P2
50
65
1600
P2
1,5
70
1800
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
2,5
75
2000
P1
P1
30
Lw = Lp + 8 db (A)
P1
80
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
Load F [N]
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
250
400
600
300
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
1000
1400
1800
Speed n [RPM]
Maximum permissible axial load Fa = 2000 N
42
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T7EB/EBS - Dimensions
- Weight : 55,0 kg
213,0
K
K/2
136,7
331,6
118,5
52,3
7,9
90,9
6,4 MAX
50,8
55,9
38,1
KEY 9,52
9,47
SHAFT CODE 3
* 62,2
61,9
7,9
31,5
10,0
W
90,0
50,0
38,1
KEY 7,94
7,89
38,100
T7EB
KEY 10 x 8
M10 x 20 DEEP
2,3 x 45
e x 45
SHAFT CODE 2
SHAFT CODE 4
(Keyed no SAE )
PRESSURE 19,00
Dia d
9,5
12,7
180,0
181,0
18,0
17,5
P1
41,3 M AX
38,018
P2
38,002
2,3 x 45
31,75
31,70
35,3 MAX
47,6
60,3
2,3x 45
Dia S
e x 45
Max.
Min.
T7EB 125,000 124,937
2,0
T7EBS 127,000 126,950
1,3
SHAFT CODE 1
( Keyed SAE CC )
69,8
7,9
e x 45
MOUNTING TORQUE : 68 Nm.
120,6
38,075
88,9
2,3 x 45
149,1
42,4 MAX
76,2
98,4
C.G.
76,2
2,3 x 45
102,4
M10 x 20 DEEP
74,7
7,9
T7EBS
SUCTION 88,90
PRESSURE 37,10
Shaft
1
2
3
SHAFT CODE 5
Pressure
port
1)
Series
Vi Volumetric
displacement
43
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T67EC
- Ordering Code
Model No.
Modifications
P1
P2
Displacement P1
Volumetric displacement (ml/rev.)
042 = 132,3 057 = 183,3
045 = 142,4 062 = 196,7
050 = 158,5 066 = 213,3
052 = 164,8 072 = 227,1
054 = 171,0 085 = 268,7
Code
P1
P2
S
Displacement P2
Volumetric displacement (ml/rev.)
003 = 10,8
017 = 58,3
005 = 17,2
020 = 63,8
006 = 21,3
022 = 70,3
008 = 26,4
025 = 79,3
010 = 34,1
028 = 88,8
012 = 37,1
031 = 100,0
014 = 46,0
Design letter
Porting combination (see page 72)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
33
27
10 cSt
P1
24
21
P2
18
15
P1
12
P2
9
6
3
0
0
40
80
120
160
200
240
280
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
7
5
2
0
90
120
150
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
180
210
240
P2
P2
80
120
160
200
1400
1200
40
80
120
160
200
240
Shaft
=
keyed
Fa
Shaft keyed N1
1000
800
400
600
0
40
60
600
P2
65
1600
P1
1
60
70
1800
P1
30
75
P1
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
Load F [N]
80
2000
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
UNC thread
00
01
1.1/2"
1.1/2"
1"
3/4"
3.1/2"
3.1/2"
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Type of shaft
1 = keyed (SAE CC)
2 = keyed (non SAE)
3 = splined (SAE C) 14 teeth
4 = splined (SAE CC) 17 teeth
30
Metric thread
M0
M1
1.1/2" 1.1/2"
1"
3/4"
3.1/2" 3.1/2"
240
280
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
1000
1400
Speed n [RPM]
1800
44
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T67EC
- Dimensions - Weight : 55,0 kg
213,0
331,6
181,0
90,9
136,7
118,5
52,3
12,7
7,9
90,5
6,4 MAXI
KEY 9,52
9,47
50,8
76,2
127,00
126,95
98,4
102,4
74,7
17,5
M10 x 20 DEEP
MOUNTING TORQUE : 68 Nm
1/2-13 UNC x 23,4 DEEP - 4 HOLES
5/8-11 UNC x 29,5 DEEP - 4 HOLES
17,5
(M16 x 29,5 DEEP - METRIC VERSION) (M12 x 23,4 DEEP -METRIC VERSION )
35,7
69,9
3/8-16 UNC x 19 DEEP - 4 HOLES
26,2
(M10 x 19 DEEP - METRIC VERSION)
17,8
34,9
62,2
13,1
7,9
1,3 x 45
61,9
7,9
42,36 MAXI
38,100
38,075
2,3 x 45
SHAFT CODE 1
( Keyed SAE CC )
38,1
31,5
KEY 7,94
7,89
2,3 x 45
P1
P2
2,3 x 45
SHAFT CODE 3
SHAFT CODE 4
35,27 MAXI
52,4
26,2
2,3 x 45
31,75
31,70
7,9
149,1
88,9
76,2
C.G.
SHAFT CODE 2
PRESSURE 25.4
SUCTION 88,9
PRESSURE 37,1
Shaft
1
2
( Keyed no SAE )
Series
Vi Volumetric
displacement
45
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7ED/T7EDS - Ordering
Code
Model No.
Modifications
P1
P2
Displacement P1
Volumetric displacement (ml/rev.)
042 = 132,3 057 = 183,3
045 = 142,4 062 = 196,7
050 = 158,5 066 = 213,3
052 = 164,8 072 = 227,1
054 = 171,0 085 = 268,7
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Displacement P2
Volumetric displacement (ml/rev.)
B14 = 44,0
B31 = 99,2
B17 = 55,0
B35 = 113,4
B20 = 66,0
B38 = 120,6
B22 = 70,3
B42 = 137,5
B24 = 81,1
045 = 145,7
B28 = 90,0
050 = 158,0
Type of shaft T7EDS
1 = keyed (SAE CC)
2 = keyed (non SAE)
Design letter
Porting combination (see page 72)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
30
24 cSt
27
10 cSt
P1
24
P2
21
18
15
12
P1
P2
6
3
0
0
30
60
90
120
150
180
210
240
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
7
6
5
4
3
2
1
0
P1
60
90
120
150
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
5
4
180
210
240
1
0
90
40
80
120
160
200
240
120
150
180
2600
=
Shaft
keyed
F
Fa
Shaft keyed N1
2200
1800
1000
P2
60
60
1400
P2
30
65
3000
P2
3
2
70
3400
P1
30
75
P1
3800
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
80
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
Load F [N]
33
210
600
600
240
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
1000
1400
Speed n [RPM]
1800
46
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T7ED/EDS Dimensions - Weight : 66,0 kg
213,0
K
K/2
148,2
361,0
52,3
7,9
6,4 MAXI
133,5
90,9
50,8
T7EDS
98,4
C.G.
2,3 x 45
161,0
89,0
81,0
76,2
S
M10 x 20 DEEP
38,10
38,05
42,36 MAX
101,6
102,4
KEY 9,52
9,47
e x 45
SHAFT CODE 1
KEY 7,94
7,89
SHAFT CODE 4
SAE CC INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 12/24
17 TEETH - 30 PRESSURE ANGLE
SHAFT CODE 3
SAE C INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SIDE FIT
J498b - PITCH 12/24
14 TEETH - 30 PRESSURE ANGLE
31,75
(Keyed no SAE )
Dia d
9,5
12,7
180,0
181,0
18,0
17,5
35,7
T7ED
50,0
KEY 10 x 8
M10 x 20 DEEP
P1
2,3 x 45
e x 45
SHAFT CODE 2
31,70
2,3 x 45
P2
35,27 MAX
58,7
29,4
2,3 x 45
17,8
38,018
2,3 x 45
38,1
38,002
61,9
38,1
10,0
W
90,0
65,1
7,9
B x 30 DEEP - 4 HOLES
77,8
38,9
41,3 MAXI
55,9
31,5
C x 24 DEEP - 4 HOLES
30,2
15,1
130,2
62,2
7,9
(Keyed SAE CC )
69,8
PRESSURE 31,80
SUCTION 101,60
Shaft
1
2
3
PRESSURE 37,10
SHAFT CODE 5
Pressure
port
1)
Series
Vi Volumetric
displacement
47
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7EE/T7EES - Ordering
Code
Model No.
Modifications
P1
P2
Displacement P1 & P2
Volumetric displacement (ml/rev.)
042 = 132,3 057 = 183,3
045 = 142,4 062 = 196,7
050 = 158,5 066 = 213,3
052 = 164,8 072 = 227,1
054 = 171,0 085 = 268,7
Type
Code
Coupling adaptor
0 = none
2 = SAE B
3 = SAE BB
* for SAE C, please contact Parker Denison
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Porting combination (see page 72)
00 = standard
33
30
24 cSt
27
10 cSt
24
P1-P2
21
18
15
P1-P2
12
9
6
3
0
0
30
60
90
120
150
180
210
240
Pressure p [bar]
Do not operate pump more than 5 seconds at any speed or viscosity
if internal leakage is higher than 50% of theoretical flow.
Total leakage is the sum of each section loss under its respective
operating conditions.
power loss hydromechanical (typical)
u = 32 cSt
Lw = Lp + 8 db (A)
80
75
70
65
0
40
80
120
160
200
240
Pressure p [bar]
Double pump noise level is given with both stages discharging at the
pressure value indicated on the curve.
7
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
3400
3000
P1-P2
Load F [N]
85
P1-P2
P1-P2
2
1
2600
Shaft
F
keyed
Fa
Shaft keyed N1
2200
1800
1400
1000
0
0
30
60
90
120
150
180
210
600
600
240
Pressure p [bar]
Total hydromechanical power loss is the sum of each section loss
under its respective operating conditions.
1000
1400
1800
Speed n [RPM]
Maximum permissible axial load Fa = 2000 N
48
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T7EE/EES - Dimensions
- Weight : 95,0 kg
273,0
224,5
406,8
157,9
42,9
167,3
20.6
90,9
8,0
46
224,5
38,100
M10 x 20 DEEP
38,075
118
86,6
170,0
104,5
C.G.
273,0
165,10
42,36 MAX
63,5
165,05
101,65
101,70 *
98,4
115
139,7
KEY 9,5 2
9,47
1,5 x 45
15,5
COUPLING ADAPTAT OR
SHAF T CODE 1
(KEYED SAE C-C)
9,0
427,8
62,2
92,0
10,0
8,0
KEY 14 x 9
35,7
35,7
63,0
6,4
75,0
Shaft
1
2
3
4
5
63,5
Vi Volumetric
displacement
042
132,3 ml/rev
045
142,4 ml/rev
050
158,5 ml/rev
P1
052
164,8 ml/rev
054
171,0 ml/rev
&
057
183,3 ml/rev
062
196,7 ml/rev
P2
066
213,3 ml/rev
072
227,1 ml/rev
085
268,7 ml/rev
1)
085 = 90 bar max. int.
* For SAE C, please contact Parker Denison.
KEY 11,11
11,06
48,8
1/2-13 UNC
x 2 4 DEEP
3,0 x 45
Series
100,0
8,0
2,3 x 45
SHAF T CODE 4
8,0
SHAF T CODE 2
49,3 MAX
9,0
49
44,45
Coupling adaptor
Without coupling
SAE B - 13 teeth - Pitch 16/32
Major dia. (min) 22,225 - Minor dia. (min) 19,134
SAE BB - 15 teeth - Pitch 16/32
Major dia. (min.) 25,400 - Minor dia. (min.) 22,268
1,5 x 45
22,0
44,40
Code
0
250,000
T7EE
22,0
SUCTION 101,6
PRESSURE 38,1
249,928
45,000
3,0 x 45
SHAFT CODE 3
PRESSURE 37,1
48,5 MAX
P1
44,975
M12 x 24 DEEP
222,7
209
69,9
130,2
P2
69,9
173,3
146,0
2,3 x 45
SHAF T CODE 5
(KEYED SAE D & E)
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7DBB
/ T7DBBS - Ordering Code
Model No.
Modifications
P1
P2
P3
Displacement for P1
Volumetric displacement (ml/rev)
B14 = 44,0
B31 = 99,2
B17 = 55,0
B35 = 113,4
B20 = 66,0
B38 = 120,6
B22 = 70,3
B42 = 137,5
B24 = 81,1
045 = 145,7
B28 = 90,0
050 = 158,0
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Porting combination (see pages 72 - 73)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Pressure
port
1)
Series
Vi Volumetric
displacement
50
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7/T67/T6C
22
20
24 cSt
75
P1
10 cSt
18
16
14
12
P3-P3
10
8
P1
P2-P3
4
2
70
65
60
55
0
0
50
100
150
200
250
300
40
80
120
160
200
240
Pressure p [bar]
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
5
4
P1
3
1
1400
P1
0
30
60
90
120
150
180
210
240
Load F [N]
3,5
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
3
2,5
2
P2-P3
1,5
0,5
100
150
200
Fa
Shaft keyed N1
1200
1000
800
400
P2-P3
0
50
=
Shaft
F
keyed
600
P2-P3
1600
P1
1800
250
300
200
600
900
1200
1500
1800
2100
Pressure p [bar]
Speed n [RPM]
51
2400
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
41,0 MAXI
38,002
31,5
61,0
2,3 x 45
d1
7,9
Keyed SAE CC
MOUNTING TORQUE : 68 Nm
5,4
189,0
138
6,35 MAXI
38,1
PRESSURE C
P3
PRESSURE 25,4
P2
SUCTION 101,6
PRESSURE 31,8
P1
M10 x 20 DEEP
KEY 9,52
9,47
SHAFT CODE 2
2,3 x 45
63,5
89,7
K2
K1
K2
421,8
101,6
SHAFT CODE 4
7,9
SHAFT CODE 5
38,018
M10 x 20 DEEP
d2
75,5
74,0
A
50,0
52,4
KEY 10 x 8
38,100
101,6
91,0
68,0
42,3 MAXI
127,0
95,6
10,0
38,075
122,4
SHAFT CODE 3
2,3 x 45
KEY 6,35
6,30
2,3 x 45
Keyed no SAE
SHAFT CODE 1
49,3
7,9
84
e x 45
7,9
38
56
w
99,5
130,2
64,3
31,75 -0.05
52
58,7
S
34,6 MAXI
213,1
Catalogue HY29-0001/UK
Industrial Vane Pumps
T7DBB/S-DCB/S-DCC/S
- Dimensions - Weight : 61 kg T7/T67/T6C
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7DCB
/ T7DCBS - Ordering Code
Model No.
T7/T67/T6C
Modifications
P1
P2
P3
Displacement for P1
Volumetric displacement (ml/rev)
B14 = 44,0
B24 = 81,1
B38 = 120,6
B17 = 55,0
B28 = 90,0
B42 = 137,5
B20 = 66,0
B31 = 99,2
045 = 145,7
B22 = 70,3
B35 = 113,4
050 = 158,0
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and fire
resistant fluids)
Displacement for P2
Volumetric displacement (ml/rev)
003 = 10,8
012 = 37,1
022 = 70,3
005 = 17,2
014 = 46,0
025 = 79,3
006 = 21,3
017 = 58,3
028 = 88,8
008 = 26.4
020 = 63,8
031 = 100,0
010 = 34,1
Displacement for P3
Volumetric displacement (ml/rev)
B02 = 5,8
B07 = 22,5
B12 = 41,0
B03 = 9,8
B08 = 24,9
B14 = 45,0
B04 = 12,8
B09 = 28,0
B15 = 50,0
B05 = 15,9
B10 = 31,8
B06 = 19,8
B11 = 35,0
Design letter
Porting combination (see pages 72 - 73)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Type of shaft T7DCB & T7DCBS Type of shaft T7DCBS
1 = keyed (non SAE)
5 = keyed (ISO 3019/2 - G38M)
2 = keyed (SAE CC)
3 = splined 12/24 (SAE C) (14 teeth)
4 = splined 12/24 (SAE CC) (17 teeth)
Series
Vi Volumetric
displacement
44,0 ml/rev
55,0 ml/rev
66,0 ml/rev
70,3 ml/rev
81,1 ml/rev
90,0 ml/rev
99,2 ml/rev
113,4 ml/rev
120,6 ml/rev
137,5 ml/rev
145,7 ml/rev
158,0 ml/rev
53
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
22
80
P1
20
10 cSt
P2
75
16
14
12
P1
10
70
P2
24 cSt
18
P3
65
P3
60
0
0
50
100
150
200
250
300
40
80
120
160
200
240
Pressure p [bar]
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
P1
1800
P1
30
60
90
120
150
180
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
3
2
P1
1600
210
1400
P2
240
Load F [N]
6
5
4
3
2
1
0
P2
P2
0
0
3
40
80
120
160
200
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
P2-P3
240
280
100
150
200
1000
800
200
600
P3
50
Fa
Shaft keyed N1
400
P3
0
0
keyed
F
600
P3
1200
= Shaft
=
250
300
900
1200
1500
1800
2100
Pressure p [bar]
Speed n [RPM]
54
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2400
Catalogue HY29-0001/UK
T7/T67/T6C
22
80
24 cSt
10 cSt
18
P1
20
P2-P3
16
14
12
10
P1
P2-P3
6
4
2
75
70
65
60
0
0
40
80
120
160
200
240
280
40
80
120
160
200
240
Pressure p [bar]
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
5
4
P1
3
1
1400
P1
30
3,5
3
2,5
2
1,5
1
0,5
0
60
90
120
150
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
180
210
Load F [N]
0
0
240
P2-P3
P2-P3
40
80
120
160
200
240
=
Shaft
keyed
F
Fa
Shaft keyed N1
1200
1000
800
600
400
P2-P3
1600
P1
1800
280
200
600
900
1200
1500
1800
2100
Pressure p [bar]
Speed n [RPM]
55
2400
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7DCC
/ T7DCCS - Ordering Code
Model No.
Modifications
P1
P2
P3
Displacement for P1
Volumetric displacement (ml/rev)
B14 = 44,0
B31 = 99,2
B17 = 55,0
B35 = 113,4
B20 = 66,0
B38 = 120,6
B22 = 70,3
B42 = 137,5
B24 = 81,1
045 = 145,7
B28 = 90,0
050 = 158,0
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Porting combination (see pages 72 - 73)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Series
Vi Volumetric
displacement
56
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T7DDB
/ T7DDBS - Ordering Code
Model No.
T7/T67/T6C
Modifications
P1
P2
P3
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and fire
resistant fluids)
Displacement for P3
Volumetric displacement (ml/rev)
B02 = 5,8
B09 = 28,0
B03 = 9,8
B10 = 31,8
B04 = 12,8
B11 = 35,0
B05 = 15,9
B12 = 41,0
B06 = 19,8
B14 = 45,0
B07 = 22,5
B15 = 50,0
B08 = 24,9
Design letter
Porting combination (see pages 72 - 73)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Pressure
port
1)
Series
Vi Volumetric
displacement
57
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
22
80
P1-P2
20
24 cSt
18
10 cSt
16
14
12
10
P1-P2
P3
6
4
P3
2
50
100
150
200
250
75
70
65
60
0
0
300
40
80
120
160
200
240
Pressure p [bar]
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
2000
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
5
4
P1-P2
P1-P2
2
1
1600
P1-P2
0
0
3,5
30
60
90
120
150
180
210
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
3
2,5
Load F [N]
1800
240
P3
2
1,5
1
50
100
150
200
F
Shaft
F
Fa
keyed
Fa
Shaft keyed N1
Shaft keyed N1
1400
1200
1000
600
P3
= = =
800
P3
0,5
250
400
600
300
900
1200
1500
1800
2100
Pressure p [bar]
Speed n [RPM]
58
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2400
50,0
KEY 10 x 8
41,0 MAXI
91,0
50,8
d2
101,6
2,3 x 45
KEY 9,52
9,47
SHAFT CODE 2
P3
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
T7DDB
T7DDBS
Series
P2
PRESSURE 31,8
206,5
148,5
19,0
P1
SUCTION 101,6
77,8
SHAFT CODE 3
2,3 x 45
64,3
S
SAE C INVOLUTE SPLINE DATA
CLASS 1-FLAT ROOT SID E FIT
J498b - PITCH 12/24
14 TEETH - 30 PRESSURE ANGLE
38,0
56,0
7,9
6,4 MAXI
Keyed SAE C
PRESSURE 31,8
P1
30,2
KEY 7,94
7,89
SHAFT CODE 1
e x 45
2,3 x 45
49,3
6,4 MAXI
W
7,9
84,0
M10 x 20 DEEP
38,1
C.G.
114,9
PRESSURE C
P2
7/16-14UNC x 24 DEEP
M12 x 24 DEEP-METRIC VERSION
B
30,2
P3
125,0
5/8-11UNC x 30 DEEP
M16 x 30 DEEP-METRIC VERSION
MOUNTING TORQUE : 80 Nm
74,7
3/8-16UNC x 19 DEEP
M10 x 19 DEEP-METRIC VERSION
Keyed SAE CC
7,9
213,0
K1
K2
SHAFT CODE 5
10,0
68,0
SHAFT CODE 4
2,3 x 45
M10 x 20 DEEP
d1
M10 x 20 DEEP
38,018
38,002
K2
31,5
42,36 MAXI
62,0
182,2
7,9
58,7
91,2
A
120,0
130,2
101,6
58,7
59
38,10
38,05
31,75
31,70
35,27 MAXI
455,0
Catalogue HY29-0001/UK
Industrial Vane Pumps
T7DDB/DDBS
- Dimensions - Weight : 66 kg T7/T67/T6C
SHAFT CODE 4
17,5
59,6
2,3 x 45
KEY 7.94
7.89
P3
P2
114,5
7/16-14UNC x 24 DEEP
M12 x 24 DEEP-METRIC VERSION
P2
PRESSURE 31,8
PRESSURE C
P3
30,2
206,5
148,5
101,6
P1
SU CTION 101,6
77,8
PRESSURE 31,8
P1
30,2
19,0
38,1
C.G.
115,0
455,0
125,0
5/8-11UNC x 30 DEEP
M16 x 30 DEEP-METRIC VERSION
MOUNTING TORQUE : 80 Nm
74,7
3/8-16UNC x 19 DEEP
M10 x 19 DEEP-METRIC VERSION
B
2,3 x 45
KEY 9,52
9,47
( KEYED SAE CC )
50,8
SHAFT CODE 2
7,9
91,0
213,0
181,0
114,5
(KEYED NO SAE)
SHAFT CODE 5
7,9
M10 x 20 DEEP
34,90
34,85
38,42 MAXI
84,0
38,10
2,3 x 45
M10 x 20 DEEP
101,6
91,2
31,5
58,7
14
,3
130,2
84,0
56,0
7,9
6,4 MAXI
SHAFT CODE 3
2,3 x 45
( KEYED SAE C )
64,3
127,00
37,7
KEY 7,94
7,89
35,27 MAXI
SHAFT CODE 1
1,3 x 45
2,3 x 45
49,3
6,4 MAXI
12,7
7,9
31,70
31,75
62,0
38,05
120,0
58,7
M10 x 20 DEEP
7,9
42,36 MAXI
60
182,2
Catalogue HY29-0001/UK
T67DDCS
- Dimensions - Weight : 66 kg
Industrial Vane Pumps
T7/T67/T6C
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
126,95
Catalogue HY29-0001/UK
T67DDCS
- Ordering Code
Model No.
T7/T67/T6C
P1
P2
Modifications
P3
P3
Code
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and fire
resistant fluids)
Displacement for P3
Volumetric displacement (ml/rev)
003 = 10,8
017 = 58,3
005 = 17,2
020 = 63,8
006 = 21,3
022 = 70,3
008 = 26,4
025 = 79,3
010 = 34,1
028 = 88,8
012 = 37,1
031 = 100,0
014 = 46,0
Design letter
Porting combination (see pages 72 - 73)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Type of shaft
1 = keyed (SAE C)
2 = keyed (SAE CC)
3 = splined 12/24 (SAE C) (14 teeth)
4 = splined 12/24 (SAE CC) (17 teeth)
5 = keyed (non SAE)
Series
Vi Volumetric
displacement
61
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
24 cSt
P1-P2
10 cSt
20
18
P3
16
14
12
10
P1-P2
P3
6
4
2
0
0
40
80
120
160
200
240
75
70
65
60
280
40
80
120
160
200
240
Pressure p [bar]
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
5
4
2000
P1-P2
1800
P1-P2
1600
P1-P2
0
0
30
60
90
120
150
180
210
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2500 RPM
Load F [N]
240
P3
1400
=
=
Shaft
keyed
F
Fa
Shaft keyed N1
1200
1000
800
P3
P3
600
400
600
0
0
40
80
120
160
200
240
280
900
1200
1500
1800
2100
Pressure p [bar]
Speed n [RPM]
62
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2400
Catalogue HY29-0001/UK
T7EDB
/ T7EDBS - Technical data
T7/T67/T6C
30
24 cSt
P1
10 cSt
27
33
24
21
P2
18
P1
15
12
P2
P3
P3
80
75
70
65
0
0
50
100
150
200
250
300
40
80
120
160
200
240
Pressure p [bar]
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
1800
P1
P1
1600
P1
0
30
6
5
4
3
2
1
0
60
90
120
150
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
180
210
1400
240
Load F [N]
8
7
6
5
4
3
2
1
0
P2
P2
P2
30
60
90
120
150
180
210
Shaft
F
keye
Fa
Shaft keyed N1
1200
1000
800
240
600
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
2
1
P3
400
P3
P3
0
0
50
100
150
200
250
200
600
300
1000
1400
1800
Pressure p [bar]
Speed n [RPM]
63
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T7EDB
/ T7EDBS - Ordering Code
Model No.
Modifications
P1
P2
P3
Displacement for P1
Volumetric displacement (ml/rev)
042 = 132,3 054 = 171,0 066 = 213,3
045 = 142,4 057 = 183,3 072 = 227,1
050 = 158,5 062 = 196,7 085 = 268,7
052 = 164,8
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Design letter
Displacement for P2
Volumetric displacement (ml/rev)
B14 = 44,0
B24 = 81,1
B38 = 120,6
B17 = 55,0
B28 = 90,0
B42 = 137,5
B20 = 66,0
B31 = 99,2
045 = 145,7
B22 = 70,3
B35 = 113,4
050 = 158,0
Displacement for P3
Volumetric displacement (ml/rev)
B02 = 5,8
B07 = 22,5
B11 = 35,0
B03 = 9,8
B08 = 24,9
B12 = 41,0
B04 = 12,8
B09 = 28,0
B14 = 45,0
B05 = 15,9
B10 = 31,8
B15 = 50,0
B06 = 19,8
Pressure
port
1)
Series
Vi Volumetric
displacement
132,3 ml/rev
142,4 ml/rev
158,5 ml/rev
164,8 ml/rev
171,0 ml/rev
183,3 ml/rev
196,7 ml/rev
213,3 ml/rev
227,1 ml/rev
268,7 ml/rev
64
48,8
106,0
273,0
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Series
P3
P2
148,4
22,0
20,6
Dia d
120,0
C.G.
171,3
133,3
38,1
P1
35,7
100,7
101,6
77,8
42,9
8,2
6,4
10,0
w
22,0
P1
139,7
115,0
MOUNTING TORQUE : 300 Nm
31,8
P2
30,2
468,0
MOUNTING TORQUE : 54 Nm
P3
T7EDB
T7EDBS
SHAFT CODE 3
3,0 x 45
8,0
75,0
110,0
273,0
45
101,6
58,7
74,7
A
120,0
130,2
69,8
208,9
KEY 11,11
11,06
T7EDBS
44,45
44, 40
SHAFT CODE 1
3,0 x 45
KEY 14 x 9
T7EDB
49,30 MAX
SHAFT CODE 2
63,0
e x 45
92,0
e x 45
2,3 x 45
63,5
100,0
S
S
K/2
M12 x 24 DEEP
65
45,000
44, 975
Catalogue HY29-0001/UK
48,5 MAX
T7EDB/EDBS Dimensions - Weight : 102 kg
T7/T67/T6C
273,0
48,8
SHAFT CODE 3
3,0 x 45
8,0
106,0
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
T67EDC
T67EDCS
P3
P2
148,4
22,0
20,6
Dia d
120,0
C.G.
171,3
133,3
38,1
P1
35,7
100,7
101,6
77,8
42,9
8,2
6,4
10,0
w
22,0
P1
139,7
115,0
MOUNTING TORQUE : 300 Nm
31,8
P2
30,2
468,0
MOUNTING TORQUE 1: 90 Nm
MOUNTING TORQUE : 54 Nm
Series
P3
120,0
101,6
58,7
75,0
110,0
273,0
45
130,2
69,8
KEY 11,11
11,06
T67EDCS
SHAFT CODE 1
3,0 x 45
KEY 14 x 9
T67EDC
44,45
44, 40
SHAFT CODE 2
63,0
e x 45
92,0
e x 45
2,3 x 45
63,5
100,0
49,30 MAX
48,5 MAX
K/2
208,9
S
S
74,7
A
66
M12 x 24 DEEP
Catalogue HY29-0001/UK
45,000
44, 975
T67EDC/EDCS
- Dimensions - Weight : 102 kg
Industrial Vane Pumps
T7/T67/T6C
Catalogue HY29-0001/UK
T67EDC
/ T67EDCS - Ordering Code
Model No.
T7/T67/T6C
Modifications
P1
P2
P3
Displacement for P1
Volumetric displacement (ml/rev)
042 = 132,3 054 = 171,0 066 = 213,3
045 = 142,4 057 = 183,3 072 = 227,1
050 = 158,5 062 = 196,7 085 = 268,7
052 = 164,8
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
4 = S4 EPDM - 7 bar max. (for fire resistant fluids)
5 = S5 VITON - 7 bar max. (for mineral oil and
fire resistant fluids)
Displacement for P2
Volumetric displacement (ml/rev)
B14 = 44,0
B24 = 81,1 B38 = 120,6
B17 = 55,0
B28 = 90,0 B42 = 137,5
B20 = 66,0
B31 = 99,2 045 = 145,7
B22 = 70,3
B35 = 113,4 050 = 158,0
Displacement for P3
Volumetric displacement (ml/rev)
003 = 10,8
012 = 37,1
022 = 70,3
005 = 17,2
014 = 46,0
025 = 79,3
006 = 21,3
017 = 58,3
028 = 88,8
008 = 26.4
020 = 63,8
031 = 100,0
010 = 34,1
Design letter
Porting combination (see pages 72 - 73)
00 = standard
Direction of rotation (shaft end view)
R = Clockwise
L = Counter-clockwise
Type of shaft T67EDCS
Type of shaft T67EDC
1 = keyed (ISO 3019/2 - G45N) 2 = keyed (SAE D & E)
3 = splined 8/16 (SAE D & E) (13 teeth)
Series
Vi Volumetric
displacement
132,3 ml/rev
142,4 ml/rev
158,5 ml/rev
164,8 ml/rev
171,0 ml/rev
183,3 ml/rev
196,7 ml/rev
213,3 ml/rev
227,1 ml/rev
268,7 ml/rev
67
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
T67EDC
/ T67EDCS - Technical data
33
30
10 cSt
24 cSt
27
P1
24
21
P3
P2
18
15
P1
12
P2
P3
6
3
0
0
40
80
120
160
200
240
Lw = Lp + 8 db (A)
80
75
70
65
280
40
80
120
160
200
240
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
8
7
6
5
4
3
2
1
0
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
1800
P1
P1
P1
30
6
5
4
3
2
1
0
60
90
120
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
150
180
1400
210
240
P2
P2
P2
0
4
30
60
90
120
150
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
3
2
180
210
240
P3
80
120
160
200
Fa
Shaft keyed N1
1200
1000
800
400
P3
200
600
0
40
keye
F
600
P3
1
0
=Shaft
=
1600
Load F [N]
Pressure p [bar]
240
280
1000
1400
1800
Pressure p [bar]
Speed n [RPM]
68
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T7EEC
/ T7EECS - Technical data
T7/T67/T6C
35
24 cSt
10 cSt
30
85
P1-P2
25
20
P3
15
P1-P2
10
P3
5
0
80
75
70
65
40
80
120
160
200
240
280
40
80
120
160
200
240
Pressure p [bar]
Pressure p [bar]
Triple pump noise level is given with all stages discharging at the
pressure value indicated on the curve.
2000
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
6
5
P1-P2
4
2
1600
P1-P2
1
0
0
30
60
90
120
150
180
210
Load F [N]
1800
P1-P2
240
n = 1000 RPM
n = 1500 RPM [24 cSt]
n = 2200 RPM
P3
Shaft
F
keyed
Fa
Shaft keyed N1
1400
1200
1000
800
P3
P3
600
0
0
40
80
120
160
200
240
280
400
600
1000
1400
1800
Pressure p [bar]
Speed n [RPM]
69
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
2200
Catalogue HY29-0001/UK
T7EEC
/ T7EECS - Ordering Code
Model No.
Modifications
P1
P2
P3
Seal class
1 = S1 BUNA N - 0,7 bar max. (for mineral oil)
Design letter
Series
Vi Volumetric
displacement
132,3 ml/rev
142,4 ml/rev
158,5 ml/rev
164,8 ml/rev
171,0 ml/rev
183,3 ml/rev
196,7 ml/rev
213,3 ml/rev
227,1 ml/rev
268,7 ml/rev
70
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
136,50
273,00
K/2
75,0
115,0
515,2
C.G.
115,0
118,0
MOUNTING TORQUE : 300 N.m
160,5
168,3
202,7
139,7
K/2
42,9
W
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
T7EEC
T7EECS
Series
PRESSURE 36,4
P2
PRESSURE C
P3
22,0
20,8
Dia d
P1
PRESSURE 38,1
SUCTION 101,6
74,5
210
A
69,85
136,50
119,6
130,2
71
69,85
63,00
KEY 14 h9
SHAFT CODE 4
3 x 45
75,0
48,8
SHAFT CODE 2
3,0 x 45
e x 45
92,0
45,000
44,975
10,0
48,5 maxi
S
273,00
Catalogue HY29-0001/UK
Industrial Vane Pumps
T7EEC/EECS - Dimensions
- Weight : 114,8 kg T7/T67/T6C
Catalogue HY29-0001/UK
Porting Diagrams
T7BB/T7BBS
T6CC
00
01
02
03
04
05
06
07
P1-P2
P1-P2
S-P1-P2
P1-P2
P1
P1
P1
P1-S
T67CB
T7DB/T7DBS
S
P2
S
P2
T67DC
08
09
10
11
12
13
14
15
P1-S
P1-S
P1
P1
P1
P1
P1
P1
T7EB/T7EBS
P2
P2
P2
P2
P2
16
P1
17
18
P1
P1
P2
19
20
P1
P1
21
P1
25
26
27
28
P1-S
P1-S
P1-S
P1
P2
T7ED/T7EDS
P2
01
02
03
04
05
06
07
S-P1-P2
P1-P2
P1
P1
P1
P1-S
S
P2
S
P2
P2
S-P2
08
09
10
11
12
13
14
15
P1-S
P1-S
P1
P1
P1
P1
P1
P1
P2
P2
S
S
P2
P2
P2
P2
00
01
02
03
04
05
06
07
P1-P2-P3
P1-P2-P3
S-P1-P2-P3
P1-P2-P3
P1
P1
P1
P1-S
T7DCC/T7DCCS
S
P2
P3
S
P2
P3
P2
P3
S-P2-P3
08
09
10
11
12
13
P1-S
P1-S
P1
P1-P2
P1-P2
P1-P3
T7EDB/T7EDBS
P2
P3
14
15
P1
P1-P3
S
P2
S
P3
P2-P3
S
P2
P2-P3
S-P3
16
17
18
19
20
21
22
S-P1-P2
S-P1-P2
S-P1-P2
S-P1-P3
S-P1-P3
S-P1-P3
P1-P2
P3
P3
P2-P3
24
P1
P2
P3
P2
P3
P2
25
26
27
28
29
30
P1
P1
P1-P3
P1-S
P1-S
P1-S
P2
P3
S
S
P2
P2
P3
S-P2
23
P1
S
P3
P2
P3
P2
P2
P3
31
P1-S
P3
P3
P3
P2
P2
32
33
34
35
36
37
38
39
P1-S
P1-S
P1-P2
P1-P2
P1-P2
P1-P2
P1-P2
P1-P2
P2
P2
P3
P3
P3
S S
P3
P3
P3
S S
P3
40
41
42
43
44
45
46
P1-P3
P1-P3
P1-P3
P1-P3
P1-P3
P1
P2
P2
P2
P2
P2
P2
49
50
51
52
53
54
P1
P1
P1
P1
P1
P1
S
P3
P2
S
P3
P3
P2
56
P1
P3
P2
P2
S-P3
S-P3
57
58
59
60
61
P1
P1
P3
S
P3
P2
72
P1
P1
S
P2
P2
P1
P3
63
P1
P2
P2
P3
55
62
P1
P2
S
P3
P3
S
P2
P3
S
P2
S
P2
S-P2
P1
P3
S-P2
P2
47
S
P2
P3
48
P1
P3
P1-P3
S S
S
P3
P1
S
P1-P2
P2
T7EEC/T7EECS
31
00
P2
T67EDC/T67EDCS
S
P2
T67DDCS
P1
P2
T7DBB/T7DBBS
30
P1
P1-P2
T7EE/T7EES
T7DCB/T7DCBS
29
P2
T7DBB/T7DBBS
P2
P2
S
T7DD/T7DDS
P1
P2
S
P2
24
P2
23
P2
P2
22
P1
P1-S
P2
P2
P2
P2
P2
P2
T67EC
P2
S-P2
P1
P3
S
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
P3
P2
Catalogue HY29-0001/UK
Porting Diagrams
T7DBB/T7DBBS
64
T7DCB/T7DCBS
P3
P2
T7DCC/T7DCCS
T7DBB/T7DBBS
T67DDCS
P3
65
P1
P1
72
73
74
P1
T7EEC/T7EECS
P3
P3 P3
80
81
82
P1
88
S
P2
89
P1
P1
P2
P1
P3
S
P2
96
P2
76
77
78
P3 P1-P2
83
84
85
86
P3
1F
P3 P1-S
P1
1N
P2
P2
P2
93
94
P1-P2 P3
P1
92
P1
P3 P3
P2
P1-P2
1X
P3
P1-S
P2
S
P3 P3
1A
1B
1C
P2
P2
P2
1J
1K
1L
P1-S P3
1D
P1-S
P1-S
P3 P1-S-P2
P1-S-P2 P3
P3 P3
P1-S-P2
P1
S
P2
P3
P1
S
P2
1W
P1
P1
P1-P2 P3
S
2D
P2
2E
P1-P2
P3 P3
P2
2C
P3 P1-P2
S
P2
P3 P3
P2
2B
P1
1V
P3
S
P2
2A
P1
1U
P1
P2
P3 P3
S
P2
1T
P1
1Z
P3
P1-S-P2
P3 P3
S
P2
P2
1M
P2
1S
P1
1Y
P1
P1-P2
P3 P1-S
1H
1R
P2
P2
95
P2
P1-S
P3
S
87
P3 P1-P2
P1-S
P2
1P
P1
P1-P2
P3 P3
P3 P3
P3
S-P2
79
P1
P3
P2
99
1G
P1-S P3
P2
P1
S
P3 P3
P2
P3 P3
P1-P2
P1
P1-S
P1-P2 P3
P3 P3
1E
P1
P2
91
98
P1-S P3
P2
75
P2
97
P3 P1-S
71
P1
S-P2
P1
P1
70
P3
S-P2
S
P2
P3 P3
90
P3
P2
P1
S-P2
P2
P1
69
P1
S
P1
P2
S
P2
P3
P1
P3
P3
P2
P3 P3
P2
68
P1
P2
P2
P1
67
P1
T7EDB/T7EDBS
T67EDC/T67EDCS
66
P3
P1-P2
S
P3 P3
P1
P2
P3
73
P2
P3
02
16
17
18
20
30
08
31
19
07
28
32
21
33
29
09
01
22
34
38
40
48
10
58
13
04
46
47
45
49
59
23
00
36
11
37
27
51
05
50
42
24
53
60
43
62
52
25
03
39
35
12
41
63
14
57
44
26
61
56
15
54
55
06
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
Notes
74
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Catalogue HY29-0001/UK
General Information
! Warning
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED
HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin, its subsidiaries, sales offices and authorized distributors provide
product or system options for further investigation by users having technical expertise. Before you select or use any product
or system it is important that you analyse all aspects of your application and review the information concerning the product
or system in the current product catalogue. Due to the variety of operating conditions and applications for these products or
systems, the user, through his own analysis and testing, is solely responsible for making the final selection of the products and
systems and assuring that all performance and safety requirements of the application are met.
The products are subject to change by Parker Hannifin at any time without notice.
Offer of Sale
Please contact your Parker representation for a detailed Offer of Sale.
75
Parker Hannifin
Denison Vane Pump Division
Vierzon - France
Hydraulics Group
Sales Offices
International
Europe
Austria
Italy
Australia
Austria
The Netherlands
Canada
Norway
China
Wiener Neustadt
Tel: +43 (0)2622 23501
Fax: +43 (0)2622 66212
Corsico (MI)
Tel: +39 02 45 19 21
Fax: +39 02 4 47 93 40
Castle Hill
Tel: +61 (0)2-9634 7777
Fax: +61 (0)2-9842 5111
Wiener Neustadt
(Resp for East Europe)
Tel: +43 (0)2622 23501-970
Fax: +43 (0)2622 23501-977
Oldenzaal
Tel: +31 (0)541 585000
Fax: +31 (0)541 585459
Belgium
Ski
Tel: +47 64 91 10 00
Fax: +47 64 91 10 90
Shanghai
Tel: +86 21 5031 2525
Fax: +86 21 5834 3714
Poland
Portugal
India
Nivelles
Tel: +32 (0)67 280 900
Fax: +32 (0)67 280 999
Czech Republic
Klecany
Tel: +420 284 083 111
Fax: +420 284 083 112
Denmark
Ballerup
Tel: +45 4356 0400
Fax: +45 4373 3107
Finland
Vantaa
Tel: +358 20 753 2500
Fax: +358 20 753 2200
France
Contamine-sur-Arve
Tel: +33 (0)450 25 80 25
Fax: +33 (0)450 25 24 25
Germany
Kaarst
Tel: +49 (0)2131 4016 0
Fax: +49 (0)2131 4016 9199
Ireland
Dublin
Tel: +353 (0)1 466 6370
Fax: +353 (0)1 466 6376
Warsaw
Tel: +48 (0)22 573 24 00
Fax: +48 (0)22 573 24 03
Milton, Ontario
Tel: +1 905-693-3000
Fax: +1 905-876-0788
Hong Kong
Tel: +852 2428 8008
Fax: +852 2425 6896
Leca da Palmeira
Tel: +351 22 9997 360
Fax: +351 22 9961 527
Mumbai
Tel: +91 22 5613 7081/82-85
Fax: +91 22 2768 6841/6618
Slovakia
Japan
Spain
Madrid
Tel: +34 91 675 73 00
Fax: +34 91 675 77 11
Sweden
Spnga
Tel: +46 (0)8 597 950 00
Fax: +46 (0)8 597 951 10
United Kingdom
Warwick
Tel: +44 (0)1926 317 878
Fax: +44 (0)1926 317 855
Tokyo
Tel: +(81) 3 6408 3900
Fax: +(81) 3 5449 7201
Brazil
Tel: +55 51 3470 9144
Fax: +55 51 3470 9281
South Africa
Kempton Park
Tel: +27 (0)11-961 0700
Fax: +27 (0)11-392 7213
USA
Cleveland (industrial)
Tel: +1 216-896-3000
Fax: +1 216-896-4031
Lincolnshire (mobile)
Tel: +1 847-821-1500
Fax: +1 847-821-7600
Parker Hannifin is the worlds premier supplier of motion and control systems and
solutions, with sales and manufacturing facilities throughout the world. For product
information and details of your nearest Parker sales office, visit us at www.parker.
com or call free on 00800 2727 5374.
Catalogue HY29-0001/UK
5M 03/2007 IRO
Copyright 2007
Parker Hannifin Corporation
All rights reserved