Escolar Documentos
Profissional Documentos
Cultura Documentos
July 2007
C. ARCHITECTURAL REQUIREMENTS TABLE OF CONTENTS UNSW DESIGN & CONSTRUCTION REQUIREMENTS WEB ENTRY PAGE SECTION A INTRODUCTION SECTION B DEVELOPMENT & PLANNING C. ARCHITECTURAL REQUIREMENTS SCHD. OF CHANGES REV 4.1 .............. 3 C ARCHITECURAL REQUIREMENTS............................................................................. 4 C.1 GENERAL........................................................................................................... 4 C.1.1 Structural Requirements................................................................................... 4 C.1.2 Durability of Building Fabric.............................................................................. 4 C.1.3 Concrete Mix. UNSW80 Specification............................................................. 4 C.2 EXTERNAL FABRIC........................................................................................... 4 C.2.1 Walls................................................................................................................. 4 C.2.2 Windows........................................................................................................... 4 C.2.3 External Doors.................................................................................................. 5 C.2.4 Roofs ................................................................................................................ 5 C.3 INTERNAL WALLS PARTITIONS & FINISHES ................................................. 6 C.3.1 Room Security.................................................................................................. 6 C.3.2 Partitions\ ......................................................................................................... 7 C.3.3 Internal Finishes ............................................................................................... 8 C.3.4 Walls................................................................................................................. 8 C.3.5 Floors ............................................................................................................... 8 C.4 DOORS AND DOOR FURNITURE .................................................................... 8 C.4.1 New and Existing Buildings .............................................................................. 8 C.4.2 General............................................................................................................. 8 C.4.3 Door Types:...................................................................................................... 9 C.5 EXISTING BUILDINGS (Schlage Version) ......................................................... 9 C.5.1 Type 1 - Single Leaf Fire Doors ....................................................................... 9 C.5.2 Type 2 - Double Leaf Fire Doors .................................................................... 11 C.5.3 Type 3 - Single Leaf Solid Core ..................................................................... 13 C.5.4 Type 4 - Double Leaf Solid Core .................................................................... 15 C.5.5 Type 5 - Auto Sliding Doors Frameless and Aluminium................................. 15 C.5.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail) .............. 16 C.5.7 Type 7 - Single Leaf Aluminium Doors (with Mid Rail) ................................... 17 C.6 NEW BUILDINGS (Lockwood Version) ............................................................ 18 C.6.1 Type 1 - Single Leaf Fire Doors ..................................................................... 18 C.6.2 Type 2 - Double Leaf Fire Doors .................................................................... 21 C.6.3 Type 3 - Single Leaf Solid Core ..................................................................... 22 C.6.4 Type 4 - Double Leaf Solid Core .................................................................... 25 C.6.5 Type 5 - Auto Sliding Doors Frameless and Aluminium................................. 25 C.6.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail) .............. 26 C.7 SIGNAGE ......................................................................................................... 27 C.7.1 Background .................................................................................................... 27 C.7.2 General........................................................................................................... 27
Last Updated SECTION D EXTERNAL WORKS SECTION E.1 HYDRAULIC SERVICES SECTION E.2 MECHANICAL SERVICES SECTION E.3.1 ELECTRICAL SERVICES SECTION E.3.2 LIGHTING SECTION E.3.3 SPECIAL SYSTEMS SECTION E.3.4 HIGH VOLTAGE SECTION E.4 COMMUNICATIONS SECTION E.5 LIFTS SECTION E.6 FUME CUPBOARDS SECTION F SPECIFIC AREA REQUIREMENTS APPENDIX 1 BUILDING AUTOMATION AND CONTROL SYSTEMS SPECIFICATION APPENDIX 2 CONCRETE FOR STRUCTURES APPENDIX 3 UNSW CONTROL SYSTEM STANDARDS HVAC APPENDIX 4 DOCUMENT REQUIREMENTS APPENDIX 5 UNSW STANDARD PRELIMINARIES APPENDIX 6 SECURITY SYSTEMS
July 2007
Last Updated
July 2007
Last Updated
July 2007
C.2
EXTERNAL FABRIC
C.2.1 Walls
Walls are to be durable with material selection and detailing fit for purpose. a) Base and plinth sections of walls are to resist physical wear from day to day activity such as hand trolley and skateboards collisions, and impacts and scuffing from maintenance equipment such as cleaning machines and mowers. Mitre joints in terrazzo and stone cladding and painted render plinths are not acceptable. b) Upper section of walls are to be low maintenance and resistant to degradation by weathering. Sealants are not to be the primary weather barrier.
C.2.2 Windows
All window framing is to be of commercial quality aluminium extrusion. The choice of extrusion should be based on future availability to allow later matching of profile for modification and replacement. Aluminium framing is to have a high quality corrosion resistant powdercoat or anodised finish. Powder coating is to be Dulux best quality warranty grade polyester. Anodising is to be minimum thickness 20 microns. Windows are to be constructed and installed to minimum Terrain Category 2.5. Windows to be designed and installed with mechanical means as the primary form of weatherproofing. UNSW Design & Construction Requirements (Rev 5) 4/27
Last Updated
July 2007
Vacuum-sealed double glazed sashes incorporating venetian blinds are not to be used.
C.2.2.1 Function
Windows sashes that can be cleaned from the inside are preferred. Sealants must be selected to be appropriate for their application and must be colour matched to the finished surface. Sealants are not to be used as the primary waterproofing barrier.
C.2.2.2 Cleaning
Windows should be easily accessible for cleaning. Fixed sun screening is to be offset from the windows to allow window cleaning.
C.2.4 Roofs
Pitched roofs must be provided to all buildings as far as practicable. Minimum pitch must be not less than manufacturer's recommendations and an appropriate safety margin provided to suit prevailing conditions. Roof design should discourage pigeon nesting.
C.2.4.1.1 Steel Sheet Roofing. Profiled zincalume or colorbond sheet steel roofing is acceptable for general use where there are a minimum number of roof penetrations. Sheet steel roofing is to be minimum 0.47 mm thickness. Colorbond finish is to be XSO grade. C.2.4.1.2 Aluminium Sheet Roofing. Profiled aluminium sheet roofing is to be used for roofs where there are a large number of penetrations. Associated flashings for penetrations are to be of welded construction. C.2.4.1.3 Membrane Roofing.
Last Updated
July 2007
The use of roofing membranes is to be minimised. Membrane roofing is to be Wolfin PVC membrane.
C.2.4.3.1 Roof Access Hatches Provide roof access from a service area or room such as a plantroom by a personnel door, or by means of a sliding aluminium and stainless steel hatch. A permanent steel ladder is to be provided where access to roofs is required, preferably located in a plantroom or a separately enclosed space. A hot dipped galvanised roof ladder must also be provided at changes in roof levels. C.2.4.3.2 Roof Walkways Roof walkways of approved construction must be provided to access any roof mounted plant. C.2.4.3.3 Roof Spaces All roof spaces must have permanent, fixed, adequate access. They must be provided with catwalks and be sufficiently lit to enable the roof space to be traversed without danger 24 hours a day.
C.3
Last Updated
July 2007
1 Perimeter Secure Zone - Secure Door Between Office & Coridor With Sidelights Extended throw latch. Heavy duty 100X50 aluminium section jamb Snap in jamb rebate with large fin. Door tolerance max. 3mm all round. Side lights to have mid-rail lined in line with door lock. Flush mounted striker. Obscure film to side-lights
1a Perimeter Secure Zone - Secure Door Between Office & Coridor Without Sidelights Extended throw latch Slim Line aluminium section jamb. Snap in jamb rebate with larger fin. Door tolerance max. 3mm all round. Flush mounted striker.
2 Within Secured Zone - Door Between Office & Secured Area With Sidelights Standard throw latch. Snap in jamb rebate with larger fin. Slim Line aluminium section jamb security fixed to backing column. Door tolerance max. 3mm all round. Flush mounted striker. Clear glazing side-lights 2a Within Secure Zone - Door Between Office & Secured Area Without Sidelights Standard throw latch. Snap in jamb rebate with large fin. Slim Line aluminium section jamb security fixed to backing studs. Door tolerance max. 3mm all round. Flush mounted striker.
C.3.2 Partitions\
Stud / plasterboard partitioning to be used in preference to proprietary / modular systems. Partitions to be steel stud frame construction. Partition systems to be of robust construction, provide a level of security appropriate to location and be capable of accepting doors and door furniture to UNSW requirements. UNSW Design & Construction Requirements (Rev 5) 7/27
Last Updated
July 2007
C.3.5 Floors
Floor finishes are to be durable and appropriate to use and location. Floor finishes in high traffic areas to be dirt resistant. Non-slip surfaces are to be provided to areas that are likely to be subjected to water. For example foyers and laboratories. See also: Section B
C.3.5.1 Carpet.
Preferred carpet. 80 wool/ 20 synthetic.
C.4
C.4.2 General
a) b) c) d) e) f) g) h) No locks to be mounted on the bottom or top rail of doors, for OH&S reasons. Cardax doors, refer: Appendix 6 Where Schlage series locking is used, all Cardax doors are to use ES2000 electric strike\s to have storeroom function locksets regardless of door type. Where Lockwood series locking is used, all Cardax doors are to use appropriate Lockwood electronic mortice lock. Sliding doors should be used for all main automatic exit/entry doors All hinges are to be Satin Stainless Steel, unless aluminium hinges are scheduled for aluminium doors A minimum of 3 hinges are to be used on all standard doors Drop plates for the LCN 1461 door closer are to used on aluminium doors when required
Last Updated i) j) k) l)
July 2007
All hardware is to be of heavy duty construction Any variations or changes to hardware are to be in writing and addressed to UNSW Locksmith and project managers for approval All doors requiring patch fittings are to be approved by UNSW Locksmith and project managers Include Lockwood SS092 security strike shied to all outward opening doors in secure situations.
C.5
Schlage: ND96PD Vandlgard )Storeroom) Rhodes 70mm backset, scp LCN: Super stock 1461 scp Padde: ES2000 (with micro/s tongue sensor)
Last Updated
July 2007
Swipe Card Cardax Card reader Door Stop Boyd: DS110 scp Hinges x 3 Satin stainless steel fixed pin hinges NOTE: If Cardax access is required see Section B C.5.1.2.2 Type 1B - Switchboards Cupboards
Schlage: ND96PD Vandlgard (storeroom) Rhodes 70mm backset, scp Boyd 391 with EFCO 507 R.N.L. scp LCN: Super stock 1461 scp Satin stainless steel fixed pin hinges
Lock/Latches
Lockwood: 8530 425sc Double action latch with a Padde N.E. latch (part no. FCH00103) in head of frame LCN: Super stock 1461 scp Boyd: 1515 sss push plate V/F engraved PUSH black Boyd: 1509 sss pull handle C/F engraved PULL black Boyd: DS 110 scp Satin stainless steel fixed pin hinges
Lock/Latches Door Closers H/Open 24V Connected (Optional) to Reed Switch Mimic Panel Door Closer Door Stop Hinges
Schlage: ND94PD Vandlgard (classroom) Rhodes 70mm backset, scp LCN: 4314 ME Sentronic (>900mm leaf) LCN: 4313 ME Sentronic (<900mm leaf) (Stand alone unit door release button) Sentrol: 1078 Reed switch LCN: Super stock 1461 scp Boyd: DS 110 scp Satin stainless steel fixed pin hinges
Last Updated
July 2007
Lock/Latches Door Closer Door Stop View Panel (if required) Hinges
Schlage: ND92PD Vandlgard (entrance) Rhodes 70mm backset, scp LCN: Super stock 1461 scp Boyd: DS 110 scp As per AS 1905.1 1990 Satin stainless steel fixed pin hinges
Boyd: 391 cylinder with EFCO 507 R.N.L. scp LCN: Super stock 1461 scp Satin stainless steel fixed pin hinges
Lock/Latches Boyd: 391 cylinder with EFCO 507 R.N.L. scp Hinges Satin stainless steel fixed pin hinges Note: All other furniture to be supplied by Trafalgar Pty Ltd
Schlage: ND96PD Vandlgard (storeroom) Rhodes 70mm backset, scp on (active leaf) with, Sabre: 940 scp auto flush bolts (inactive leaf) Electric Strike Padde: ES 2000 (with micro/s tongue sensor) Door Closer LCN: Super stock 1461 scp Swipe Card Cardax : Card reader Door Stop Boyd: DS 110 scp Sequence Closer Glynn Johnson: Cor 2 x FB series Hinges Satin stainless steel fixed pin hinges Note: If Cardax access is required, see Section B
Lock/Latches
Last Updated
July 2007
C.5.2.1.2 Type 2B - Fire Isolated Passages Bullnose Meeting Stiles (Non Secure)
Lock/Latches
Push/Pull Plates
Lockwood: 8530 425 Sc double action latch with a Padde N.E. latch (part no: FOH00103) in head of frame Boyd: 1515 sss push plate V/F Sengraved PUSH black Boyd: 1509 sss pull handle C/F engraved PULL black LCN: 4313ME Sentronic (<900mm leaf) LCN; 4314ME Sentronic (>900m leaf) Sentrol: 1078 Reed switch Satin stainless steel fixed pin hinges
Door Closer Connected to Reed Switch x 2 Mimic Panel Hinges Or C.5.2.1.4 Type 2C - Stairwells
Lockwood: 8530 425 Sc double action latch with a Padde N.E. latch (part no: FOH00103) in head of frame Boyd: 1515 sss push plate V/F Sengraved PUSH black Boyd: 1509 sss pull handle C/F engraved PULL black LCN: 4313ME Sentronic (<900mm leaf) LCN; 4314ME Sentronic (>900m leaf) Sentrol: 1078 Reed switch Satin stainless steel fixed pin hinges
Lock/Latches (secure)
Panic Bars (secure doors only) Door Closers Sequence Closer Door Stop Hinges
Schlage: ND94PD Vandlgard (classroom) Rhodes 700mm backset, scp (on active leaf) (T section meeting stiles Von Duprin: 2227 EOF silver finish (inactive leaf) LCN: Super stock 1461 scp Glynn Johnson: Cor 2 x FB series Boyd: DS 110 scp Satin stainless steel fixed pin hinges
July 2007
Boyd: 391 cylinder with EFCO: 507 R.N.L. scp LCN: Super stock 1461 scp Glynn Johnson: Cor 2 x FB series Sabre: 940 scp auto flush bolts Satin stainless steel fixed pin hinges
Option 1
Option 2
Option 3
Commercial quality Maximum security Minimum 40mm door thickness Schlage: Vandlgard locksets used Commercial Quality Maximum security Nominal 40mm door thickness Schlage: Vandlgard locksets used with packing plates Light commercial Low security Minimum 38mm door thickness Schlage: AL series locksets used
Commercial Quality Lock/Latches Door Closer (if required) Door Stop Door H/O (if required) Hinges
Maximum security door thickness 40mm MINIMUM Schlage: ND92PD (entrance) Rhodes 70mm backset, scp finish LCN: Super stock 1461 scp Boyd: DS 110 scp Boyd: DS 122 scp Satin stainless steel fixed pin hinges
Last Updated
July 2007
Commercial Quality Lock/Latches Door Closer (if required) Door Stop Door H/O (if required) Hinges
Maximum security door thickness 40mm NOMINAL Schlage: ND92PD (entrance) Rhodes 70mm backset, scp finish with plates LCN: Super stock 1461 scp Boyd: DS 110 scp Boyd: DS 122 scp Satin stainless steel fixed pin hinges
Light Commercial Lock/Latches Door Closer (if required) Door Stop Door H/O (if required) Hinges
Low security door thickness 38mm MINIMUM Schlage: AL53PD Saturn 70mm backset, scp finish LCN: Super stock 1461 scp Boyd: DS 110 scp Boyd: DS 122 scp Satin stainless steel fixed pin hinges
Commercial Quality Lock/Latches Door Closer (if required) Door Stop Door H/O (if required) Security Viewer (Blackout) Hinges
Maximum security door thickness 40mm MINIMUM Schlage: ND94PD (classroom) Rhodes: 70mm backset, scp finish LCN: Super stock 1461 scp Boyd: DS 110 scp Boyd: DS 122 scp EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high Satin stainless steel fixed pin hinges
Commercial Quality Lock/Latches Door Closer (if required) Door Stop Door H/O (if required)
Maximum security door thickness 40mm NOMINAL Schlage: ND94PD (classroom) Rhodes: 70mm backset, scp finish LCN: Super stock1460 scp Boyd: DS 110 scp Boyd: DS 122 scp
July 2007
EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high Satin stainless steel fixed pin hinges
Maximum security door thickness 40mm MINIMUM Lock/Latches Schlage: ND96PD (Storeroom) Rhodes 70mm backset, scp finish Electric Strike Padde: ES 2000 Door Closer LCN: Super stock 1460 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Security Viewer EFCO: Security viewer (reversed) x 2 (Blackout) One (1) at 1000 high One (1) at 1600 high Hinges Satin stainless steel fixed pin hinges Note: If Cardax access is required, see Section B C.5.3.2.7 Type 3C - Emergency Egress Doors (Stairwells Secure Areas)
Commercial Quality
Lock/Latches (Panic bar, if required) Door Closer Reed Switch Door Stop Hinges
Von Duprin: 2227 EOF (panic bar) silver finish LCN: Super stock 1461 scp Sentrol: 1078 reed switch (connected to Cardax) see Section B Boyd: DS 110 scp Satin stainless steel pin hinges
C.5.5 Type 5 - Auto Sliding Doors Frameless and Aluminium C.5.5.1 Preferred Suppliers and Installers:
Auto Entry FRB Industries Pty Ltd
Last Updated Unit 1/391 Park Road Regents Park NSW 2143 02 9644 2000 02 9645 6977 oentry @ msn.com.au 121 Bath Road Kirrawee NSW 2232 02 9545 1611 02 9545 1616
July 2007
C.5.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail)
Lever Furniture (Cylinder hole) Lever Furniture Door Closers Flush Bolts x 2
Last Updated (inactive leaf edge side) Or Von Duprin: 33277 EOF (Inactive leaf edge side)
July 2007
Door Stop Boyd: DS 110 scp Electric Strike (If required) Padde: ES 2000 Hinges Satin stainless steel fixed pin hinges Note: If Cardax access is required, see Section B C.5.6.1.1.2 Adams Rite 4710 Deadlatch (various backsets available) Short backset Mortice Lock
4066 Thumbturn 4590 Deadlatch Paddle 4560 Deadlatch Handle UNSW Cylinder on outside
C.5.6.1.1.3 1850 Deadbolt (Various backsets available) 4066 Thumbturn UNSW Cylinder on outside Inside (Optional)
Lever Furniture (Cylinder hole) Lever Furniture Door Closers Door Stop Electric Strike (If required) Hinges
Last Updated
July 2007
C.5.7.1.1.2 Adam Rite 4710 Deadlatch (various backsets available) short backset Mortice Lock. 4066 Thumbturn Inside 4590 Deadlatch Paddle Inside 4560 Deadlatch Handle Inside UNSW Cylinder on outside (Optional) (Optional) (Optional)
C.5.7.1.1.3 1850 Deadbolt (various backsets available) 4066 Thumbturn Inside UNSW Cylinder on outside (Optional)
C.6
C.6.1.2.1 Type 1A - Plantrooms UNSW Design & Construction Requirements (Rev 5) 18/27
Last Updated
July 2007
Electronic Mortice Lock Lever Furniture (Cylinder hole) Lever Furniture Door Closer Power Transfer Hinge Swipe Card Door Stop 100 X 100 X 2.5 Hinges x 3
Lockwood 3572ELEM1 (left or right) Lockwood 1801/70 SC with LED Lockwood 1905/70 SC Lockwood 7726 SSS Lockwood LC8810CP Cardax 3: Card reader Lockwood A250 SCP Lockwood 10000BB SSS
Storeroom Mortice Lock Lock Turn-snib Adaptor Lever Furniture (Cylinder hole) Lever Furniture (Turn-snib) Door Closer 100 X 100 X 2.5 Hinges x 3
Lockwood 3572X (left or right) Lockwood SP3570-6050 Lockwood 1801/70 SC Lockwood 1906 SC Lockwood 2024BC SIL Lockwood 10000BB SSS
Storeroom Mortice Lock Lever Furniture (Cylinder hole) Lever Furniture Door Closer Door Stop 100 X 100 X 2.5 Hinges x 3
Lockwood 3572X (left or right) Lockwood 1801/70 SC Lockwood 1905/70 SC Lockwood 2024BC SIL Lockwood A250 SCP Lockwood 10000BB SSS
162 X 162 Push Plate (PUSH) 162 X 162 Pull Plate (PULL) Top Latch with Non-Electric Strike Door Closer Floor Door Stop 100 X 100 X 2.5 Hinges x 3
Lockwood 20007WN SSS Lockwood 20124XN/16 SSS Lockwood 8530-105 & Padde NE Lockwood 7726 SSS Lockwood A250 SCP Lockwood 10000BB SSS
Last Updated C.6.1.2.5 Type 1C Fire Stair / Corridor (Option 2 Secure) Mechanical Storeroom Mortice Lock Lever Furniture (Cylinder hole) Lever Furniture Door Closer Floor Door Stop 100 X 100 X 2.5 Hinges x 3 Electronic Access Control Electronic Mortice Lock Lever Furniture (Cylinder hole) Lever Furniture Door Closer Power Transfer Hinge Swipe Card Door Stop 100 X 100 X 2.5 Hinges x 3
July 2007
Lockwood 3572X (left or right) Lockwood 1801/70 SC Lockwood 1905/70 SC Lockwood 7726 SSS Lockwood A250 SCP Lockwood 10000BB SSS
Lockwood 3572ELEM1 (left or right) Lockwood 1801/70 SC with LED Lockwood 1905/70 SC Lockwood 7726 SSS Lockwood LC8810CP Cardax MkIV Smartswipe Lockwood A250 SCP Lockwood 10000BB SSS
Storeroom Mortice Lock Lever Furniture (Cylinder hole) Lever Furniture Door Closer Floor Door Stop 100 X 100 X 2.5 Hinges x 3
Lockwood 3572X (left or right) Lockwood 1801/70 SC Lockwood 1905/70 SC Lockwood 7726 SSS Lockwood A250 SCP Lockwood 10000BB SSS
Boyd: 391 cylinder with EFCO 507 R.N.L. scp LCN: Super stock 1461 scp Satin stainless steel fixed pin hinges
Lock/Latches Hinges
Boyd: 391 cylinder with EFCO 507 R.N.L. scp Satin stainless steel fixed pin hinges
Last Updated Note: All other furniture to be supplied by Trafalgar Pty Ltd
July 2007
Electronic Mortice Lock Lever Furniture (Cylinder hole) Lever Furniture Automatic Flush Bolt Floor Ferrule Door Coordinator Filler Bar Door Closer Power Transfer Device Swipe Card Door Stop 100 X 100 X 2.5 Hinges x 3
Lockwood 3572ELEM1 (left or right) Lockwood 1801/70 SC Lockwood 1905/70 SC Sabre 940 SSS Doric DN205 Glynn Johnson COR-2 Glynn Johnson FB Lockwood 7726 SSS Lockwood LC8810CP Cardax 3: Card reader Lockwood A250 SCP Lockwood 10000BB SSS
C.6.2.1.2 Type 2B - Fire Isolated Passages / Fire Stair - Bullnose Meeting Stiles (Non Secure)
162 X 162 Push Plate (PUSH) 162 X 162 Pull Plate (PULL) Top Latch with Non-Electric Strike Top Latch with Double Bevel Roller Strike Door Closer Floor Door Stop 100 X 100 X 2.5 Hinges x 3
Lockwood 20007WN SSS Lockwood 20124XN/16 SSS Lockwood 8530-105 & Padde NE Lockwood 8530-305 & Padde DB Lockwood 7726 SSS Lockwood A250 SCP Lockwood 10000BB SSS
C.6.2.1.3 Type 2C - Fire Isolated Passages / Fire Stair - Rebate Meeting Stiles (Non Secure)
Last Updated
July 2007
162 X 162 Push Plate (PUSH) 162 X 162 Pull Plate (PULL) Top Latch with Non-Electric Strike Top Latch with Double Bevel Roller Strike Door Closer Door Coordinator Filler Bar Floor Door Stop 100 X 100 X 2.5 Hinges x 3
Lockwood 20007WN SSS Lockwood 20124XN/16 SSS Lockwood 8530-105 & Padde NE Lockwood 8530-305 & Padde DB Lockwood 7726 SSS Glynn Johnson COR-2 Glynn Johnson FB Lockwood A250 SCP Lockwood 10000BB SSS
Boyd: 391 cylinder with EFCO: 507 R.N.L. scp LCN: Super stock 1461 scp Glynn Johnson: Cor 2 x FB series Sabre: 940 scp auto flush bolts Satin stainless steel fixed pin hinges
Option 1
Option 2
Option 3
Commercial quality Maximum security Minimum 40mm door thickness Lockwood 3572Z SC Commercial Quality Maximum security Nominal 40mm door thickness Lockwood 3572Z SC Light commercial Low security Minimum 38mm door thickness Lockwood 3572Z SC
Last Updated
July 2007
Commercial Quality Mortise Lock Lever Furniture (Cylinder Hole) Lever Furniture Door Closer (if required) Door Stop Door H/O (if required) Hinges
Maximum security door thickness 40mm MINIMUM Lockwood 3572Z SC Lockwood 1801/70 SC Lockwood 1905/70 SC LCN Super Stock 1461 SCP Boyd: DS 110 scp Boyd: DS 122 scp Satin stainless steel fixed pin hinges
Commercial Quality Mortise Lock Lever Furniture (Cylinder Hole) Lever Furniture Door Closer (if required) Door Stop Door H/O (if required) Hinges
Maximum security door thickness 40mm NOMINAL Lockwood 3572Z SC Lockwood 1801/70 SC Lockwood 1905/70 SC LCN: Super stock 1461 scp Boyd: DS 110 scp Boyd: DS 122 scp Satin stainless steel fixed pin hinges
Light Commercial Mortise Lock Lever Furniture (Cylinder Hole) Lever Furniture Door Closer (if required) Door Stop Door H/O (if required) Hinges
Low security door thickness 38mm MINIMUM Lockwood 3572Z SC Lockwood 1801/70 SC Lockwood 1905/70 SC LCN: Super stock 1461 scp Boyd: DS 110 scp Boyd: DS 122 scp Satin stainless steel fixed pin hinges
Commercial Quality
Last Updated Mortise Lock Lever Furniture (Cylinder Hole) Lever Furniture Door Closer (if required) Door Stop Door H/O (if required) Security Viewer (Blackout) Hinges
July 2007
Lockwood 3572X SC Lockwood 1801/70 SC Lockwood 1905/70 SC LCN: Super stock 1461 scp Boyd: DS 110 scp Boyd: DS 122 scp EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high Satin stainless steel fixed pin hinges
Commercial Quality Mortise Lock Lever Furniture (Cylinder Hole) Lever Furniture Door Closer (if required) Door Stop Door H/O (if required) Security Viewer (Blackout) Highes
Maximum security door thickness 40mm NOMINAL Lockwood 3572X SC Lockwood 1801/70 SC Lockwood 1905/70 SC LCN: Super stock1460 scp Boyd: DS 110 scp Boyd: DS 122 scp EFCO: Security viewer (reversed) x 2 One (1) at 1000 high One (1) at 1600 high Satin stainless steel fixed pin hinges
Maximum security door thickness 40mm MINIMUM Mortise Lock Lockwood 3572Z SC Lever Furniture (Cylinder Hole) Lockwood 1801/70 SC Lever Furniture Lockwood 1905/70 SC Electric Strike Padde: ES 2000 Swipe Card Cardax 3: Card Reader Door Closer LCN: Super stock 1460 scp Door Stop Boyd: DS 110 scp Door H/O (if required) Boyd: DS 122 scp Security Viewer EFCO: Security viewer (reversed) x 2 (Blackout) One (1) at 1000 high One (1) at 1600 high Hinges Satin stainless steel fixed pin hinges Note: If Cardax access is required, see Section B
Commercial Quality
Last Updated
July 2007
Lock/Latches (Panic bar, if required) Door Closer Reed Switch Door Stop Hinges
Von Duprin: 2227 EOF (panic bar) silver finish LCN: Super stock 1461 scp Sentrol: 1078 reed switch (connected to Cardax) see Section B Boyd: DS 110 scp Satin stainless steel pin hinges
C.6.5 Type 5 - Auto Sliding Doors Frameless and Aluminium C.6.5.1 Preferred Suppliers and Installers:
Auto Entry Unit 1/391 Park Road Regents Park NSW 2143 02 9644 2000 02 9645 6977 oentry @ msn.com.au FRB Industries Pty Ltd 121 Bath Road Kirrawee NSW 2232 02 9545 1611 02 9545 1616
July 2007
C.6.6 Type 6 - Double Leaf Aluminium Doors (1 Leaf fixed with mid rail)
Lever Furniture (Cylinder hole) Lever Furniture Door Closers Flush Bolts x 2
C.6.6.1.1.2 Entry
Doors
to
Departments/Sections/Retail Access)
(Electronic
Electronic Mortise Lock (for Classroom, Entrance & Storeroom applications) Lever Furniture (Cylinder hole) Lever Furniture Swipe Card Door Closers Flush Bolts x 2
Lockwood 3572ELEN1 SC
Lockwood 1801/70 SC Lockwood 1905/70 SC Cardax 3: Card Reader LCN: Super stock 1461 scp Doric: DN 201 flush bolts (inactive leaf edge side)
Last Updated Or Sabre: 940 auto flush bolts (inactive leaf edge side) Or Von Duprin: 33277 EOF (Inactive leaf edge side) Door Stop Hinges
July 2007
C.7
SIGNAGE
C.7.1 Background
The University of New South Wales has a standardised and cohesive signage system based on overall simple rectilinear shapes using standardised typeface, colours and sizes. Signs are classified into types each with an individual specific function. The UNSW Signage Coordination Officer has the role of directing location specific and detailed design, based on the Universitys signage standard (manual). The role includes briefing and liaising with the project team in the pre-construction phase of projects and the engagement and directing of the nominated signage sub-contractor during the construction phase. The signage officer is to be involved prior to the commencement of the documentation phase of any project. Enquiries and requests should be directed to: Ricardo Artigas Signage Coordination Officer. Campus Services
C.7.2 General
Aluminium is the preferred construction material for all signs. Sign message panels will be rigid, stable and not subject to distortion or corrosion. Support posts for freestanding signs will utilise purpose designed aluminium extrusion to allow the use of interchangeable sign faces. All fixing devices are to be tamper-resistant and where possible concealed. Approved direct photo deposit methods of reproduction are preferred for symbol and text elements. Intended methods of manufacture and installation should be clearly specified.