Escolar Documentos
Profissional Documentos
Cultura Documentos
y a = 27 f = 24
x B = 55 b =45.7
d = 45.7 D = 55
BASE PLATE SIZE & DESIGN FORCES BASE PLATE SIZE PEDESTAL B' (cm) 80 D'(cm) 80
MEMBER
406.49 45716
DESIGN
FORCES FORCES BY "STAAD" 1.10 (Safety factor for load) Fx (kN) Fy (kN) 31.699 Fz (kN) 408.375 Mx (kN-m) -2.264 REMARK Joint No. 3, LC #107 (Max Shear)
PEDESTAL SIZE(cm) 80 x 80
-41.021
Elastic modulus of re-bar, Es = Elastic modulus of con'c, Ec = Tension strength of the bolts, Pt = Shear strength of the bolts, Ps = Design stregnth of plate, Py = Stregnth of the con'c, Pc = n Es / Ec
200 N/mm^2 30 N/mm^2 140 / 1.05 = 133.4 N/mm^2 70 / 1.05 = 66.7 N/mm^2 240 / 1.05 = 228.6 N/mm^2 24 / 1.50 = 16 N/mm^2 7
ex = ( Mx / Pz ) = -0.55 cm
<
D / 6 = 9.17 cm
The eccentricity is more than D / 6, there is uplift of the base plate which is resisted by the anchor holding down bolts.
24 cm
-0.55 cm
Pz
fp Pt
M28
The tensile force in the anchor holding down bolts Pt' = -Pz (D/2 - Y/3 - ex) / (D/2 - Y/3 + f) = -408.375 (55 / 2 - 16.43 / 3 - -0.55) / (55 / 2 - 16.43 / 3 + 24) = -200.29 kN
The maximum compressive stress in the concrete fp = 2 (Pz + Pt) / (Y x B) = 2 (408.375 + -200.29) / (16.4 55) = 0.461 kN/cm^2 = 4.61 N/mm^2 < 16 N/mm^2 [ = Strength of the con'c, Pc ] ----> O.K
TENSION CHECK Allowable tension force of bolts Pta = tension strength x bolt area x bolts No. = 133.4 490 / 1000 = 65.37 kN > -200.29 kN [ = The tension force in the bolts, Pt' ] ----> O.K
SHEAR CHECK The maximum shear force of masonry supports F = ( Fx + Fy ) = ( -41.021^2 + 31.699^2 ) = 51.84 kN
2 2
Allowable shear force of anchor holding down bolts Psa = shear strength x bolt area x bolt No. = 66.7 490 2 side / 1000 = 65.37 kN > 51.84 kN [ = The shear force in the bolts, Ft ] ----> O.K
3. BASE PLATE DESIGN Base Plate Design Without Stiffener Plate 24 cm -0.55 cm
Pz
fu
fp
m =9.3 cm
Pt
Y = 16.43 cm
The moment of cantilever strip per 1mm M = 16.43 0.461 / 2 ( 16.43 2 / 3 + -7.13 ) = 14.48 kN-cm
To check the th'k of base plate due to bending by concrete bearing pressure, the base plate of 3-side fixed boundary condition will be analysed using the moment factor for the behavior of rectangular plate by W.T.MOODY. For the detail procedures, refer to "Moments and Reactions for Rectangular Plates" by W.T.MOODY.
b1
a1
bearing
The maximum compressive stress in the concrete, fp = Partitioned plate width, a1 = Partitioned plate length, b1 = Moment Coefficiednt, Cm =
N/mm 2 mm mm
Req'd thickness of base plate bt = [ 6 Mmax. / ( 1.2 Py ) ] = [ (6 3111.15 ) / (1.2 228.6) ] = 8.25 mm