Escolar Documentos
Profissional Documentos
Cultura Documentos
TECHNICAL STANDARD
SA WATER 2007
This is an intellectual property of the South Australian Water Corporation. This document is copyright and all rights are reserved by SA Water. No part may be reproduced, copied or transmitted in any form or by any means without the express written permission of SA Water. The information contained in these Standards is strictly for the private use of the intended recipient in relation to works or projects of SA Water. These Standards have been prepared for SA Waters own internal use and SA Water makes no representation as to the quality, accuracy or suitability of the information for any other purpose. It is the responsibility of the users of these Standards to ensure that the application of information is appropriate and that any designs based on these Standards are fit for SA Waters purposes and comply with all relevant Australian Standards, Acts and regulations. Users of these Standards accept sole responsibility for interpretation and use of the information contained in these Standards. SA Water and its officers accept no liability for any loss or damage caused by reliance on these Standards whether caused by error, omission, misdirection, misstatement, misinterpretation or negligence of SA Water. Users should independently verify the accuracy, fitness for purpose and application of information contained in these Standards. The currency of these Standards should be checked prior to use.
CONTENTS
SA WATER 2007............................................................................................................... 2 APPROVAL TO DEVIATE FROM THIS STANDARD ........................................................... 2 NO CHANGES REQUIRED IN THE JANUARY 2007 EDITION ............................................ 2 CONTENTS .......................................................................................................................... 3 TABLES & FIGURES............................................................................................................ 3 REFERENCED DOCUMENTS .............................................................................................. 3 SECTION 1: SCOPE ............................................................................................................ 5 1.1 2.1 2.2 2.3 SA Waters Representative ...................................................................................... 5 Lubrication ................................................................................................................ 5 Assembly................................................................................................................... 5 Tightening ................................................................................................................. 5 SECTION 2: METHOD AND APPLICATION ....................................................................... 5
SECTION 3: BOLT SIZES ................................................................................................... 5 SECTION 4: CALIBRATION OF TORQUE DEVICE ............................................................ 6 SECTION 5: BOLT IDENTIFICATION ................................................................................. 6 SECTION 6: TIGHTENING TORQUES ................................................................................ 7
REFERENCED DOCUMENTS
AS 1110: AS 1111: AS 1252: ISO metric hexagon bolts and screws Products grades A and B ISO metric hexagon bolts and screws Products grade C High strength steel bolts with associated nuts and washers for structural engineering
AS/NZS 2451:
Bolts, screws and nuts with British Standard Whitworth threads (rationalized series)
BS 1083:
Specification for precision hexagon bolts, screws and nuts (B.S.W. & B.S.F. threads)
BS 1768:
Specification for Unified precision hexagon bolts, screws, & nuts (UNC & UNF threads). Normal series
TS 59:
Flanges
SECTION 1: SCOPE
This Technical Standard covers the procedures for tightening bolts on mechanical installations, and other non permanent joints using ordinary mild steel B.S.W. bolts in accordance with AS 2451, or metric mild steel or high strength bolts in accordance with AS 1110, AS 1111 or AS 1252. For information specific to bolting for flanges, refer to TS 59. 1.1 SA Waters Representative SA Waters Representative will be nominated to the Contractor.
M12 1/2"
M16 5/8"
M20 3/4"
M24 7/8"
M27 1"
M30 M33 M36 M39 M45 1 1/8" 1 1/4" 1 3/8" 1 1/2" 1 3/4"
Table 5.2 British Standards (BS 1083, BS 1768) (BSW and BSF Threads) Code Symbol Tensile Strength Code Symbol Minimum Tensile Strength A B P R 26 t.s.i. 28 t.s.i. 35 t.s.i. 45 t.s.i. T V X 55 t.s.i. 65 t.s.i. 75 t.s.i.
Table 5.3 AJAX, British Standard and SAE Bolts (Examples) Code Symbol/Letter/Number Tensile Strength Thread Designation No marking BSW R BSF T BSW 40 BSF 50 UNC 3 radial strokes 120E apart UNF 3 radial strokes 120E apart Table 5.4 Australian Standard Metric Bolts Grade Markings 4.6 5.8 8.8 10.9 4.6 to 46 5.8 to 58 8.8 to 88 10.9 to 109 28 t.s.i 45 55 t.s.i 55 65 t.s.i. 40 50 t.s.i. 50 60 t.s.i. 56.6 t.s.i. 53.6 t.s.i.
Minimum Tensils Strength 400 MPa 500 MPa 800 MPa 1000 MPa
Yield Stress 240 MPa 400 MPa 640 MPa 900 MPa
NOTE: 1) When there is any doubt regarding the tensile strength of the bolt, the manufacturer should be consulted. 2) Only for the commonly used bolts the tightening torques are specified in this Technical Standard. The Tables of Torques specified in this Technical Standard are also applicable to UNC and UNF bolts of equivalent tensile strength. For bolts of tensile strength higher than 53.6 t.s.i. or 800 MPa, the applied torques should be derived from Table V multiplied by the ratio of the tensile strength.
3)
4)
Table 6.1 Tightening Torque B.S.W. Bolts Material: Tensile Strength Yield Strength Bolt Sizes 40% Yield 1/2 B.S.W. 5/8 B.S.W. 3/4 B.S.W 7/8 B.S.W. B.S.W. 1 1/8 B.S.W. 1 1/4 B.S.W. 1 3/8 B.S.W. 1 1/2 B.S.W. 1 B.S.W. 11 22 40 60 92 130 185 245 315 465
= 28 t.s.i. = 16 t.s.i.
Tightening Torque (ft. lb.) 65 % Yield 18 36 64 98 150 210 300 400 510 800 80% Yield 22 45 80 120 185 260 370 490 630 990 95% Yield 26 53 94 145 220 305 440 585 745 1170
Table 6.2 Tightening Torque B.S.W. Bolts Material: Tensile Strength Yield Strength Bolt Sizes 40% Yield 1/2 B.S.W. 5/8 B.S.W. 3/4 B.S.W 7/8 B.S.W. B.S.W. 1 1/8 B.S.W. 1 1/4 B.S.W. 1 3/8 B.S.W. 1 1/2 B.S.W. 1 B.S.W. 12 25 45 68 104 146 208 276 354 557
= 35 t.s.i. = 18 t.s.i.
Tightening Torque (ft. lb.) 65 % Yield 20 41 72 110 169 236 338 450 574 900 80% Yield 25 51 90 135 208 293 416 551 709 1114 95% Yield 29 60 106 163 248 343 495 658 838 1316
Table 6.3 Tightening Torque Metric Bolts (AS 1110, AS 1111) Material: Grade 4.6 Strength Tensile Strength Yield Strength Bolt Sizes 40% Yield M 12 M 16 M 20 M 24 M 27 M 30 M 33 M 36 M 39 M 42 M 45 M 48 15 30 70 123 170 220 260 330 390 450 510 590 = 400 MPa = 240 MPa Tightening Torque (Nm) 65 % Yield 24 48 110 200 270 350 440 536 650 735 850 970 80% Yield 30 60 140 250 320 420 520 660 790 905 1040 1200 95% Yield 35 71 160 295 400 510 640 785 950 1080 1250 1420
Table 6.4 Tightening Torque Metric Bolts (AS1110) Material: Grade 5.8 Strength Tensile Strength Yield Strength Bolt Sizes 40% Yield M 12 M 16 M 20 M 24 M 27 M 30 M 33 M 36 M 39 M 42 M 45 M 48 25 50 110 205 280 360 450 550 640 750 860 980 = 500 MPa = 440 MPa Tightening Torque (Nm) 65 % Yield 40 80 170 335 460 590 740 895 1050 1225 1380 1620 80% Yield 50 100 220 420 530 700 890 1100 1280 1510 1760 2000 95% Yield 58 118 260 490 680 900 1080 1310 1550 1800 2080 2370
Table 6.5 Tightening Torque Metric Bolts (AS 1110, AS 1252) Material: Grade 8.8 Strength Tensile Strength Yield Strength Bolt Sizes 40% Yield M 12 M 16 M 20 M 24 M 27 M 30 M 33 M 36 M 39 M 42 M 45 M 48 30 60 135 246 350 450 560 660 800 900 1040 1180 = 800 MPa = 640 MPa Tightening Torque (Nm) 65 % Yield 48 96 220 400 570 730 920 1070 1300 1470 1690 1940 80% Yield 60 120 275 500 700 910 1120 1320 1600 1810 2100 2400 95% Yield 70 142 300 590 770 1000 1270 1570 1860 2160 2470 2840