Você está na página 1de 10

Seventeam Electronics Co., Ltd.

ST-550EAG

ST-550EAG
Switching Power Supply
(EPS12V)

SPECIFICATION
Revision: 1.0

SEVENTEAM ELECTRONICS CO., LTD.


2F, No.35, Lane 167, Sec.1, Tung Ho E. St,
TAIPEI, TAIWAN
TEL: 886-2-2882-9050 FAX: 886-2-2882-6230

Seventeam Electronics Co., Ltd.

ST-550EAG

** Table of Content **
1.

Input Requirements

04

1-1.

Input Voltage

04

1-2.

Frequency

04

1-3.

Inrush Current.

04

1-4.

AC Input Current.

04

1-5

Efficiency.

05

Output Requirements......................................................

05

2-1.

Output Regulations..............................................

05

2-2.

DC Load Requirements....................................

05

2-3.

Cross Regulation .....................................

06

2-4.

+5V Standby Voltage........................................

06

2-5.

DC Output Voltage Ripple And Noise...............

06

2-6.

Total Output Power...............................................

06

2-7.

Remote ON/OFF Control..................................

07

2-8.

Power Sequence....................................

07

2-9.

Power on Time (T1).....

07

2-10.

Rise Time (T2)....

07

2-11.

Power Good Delay Time (T3)....

07

2-12.

Power Good Rise Time (T4).. 08

2-13.

Hold Up Time (T5).

08

2-14.

Power Fail Signal (T6)......

08

Protections..........................................................................

08

3-1.

Over Voltage Protection...........................................

08

3-2.

Short Circuit Protection............................................

08

3-3.

Protection Reset.......................................................

09

3-4.

Over Shoot..................................................................

09

3-5.

Over Power Protection.........................................

09

Environment........................................................................

09

4-1.

Operation/Storage Temperature Range...............

09

4-2.

Humidity...................................................................

09

4-3.

Altitude.....................................................................

09

5.

Safety....................................................................................

09

6.

EMI Requirements...........................................................

10

7.

Dielectric Voltage Withstand (HI-POT)...........................

10

2.

3.

4.

Seventeam Electronics Co., Ltd.

ST-550EAG

8.

PFC..........................................................

10

9.

Electrostatic Discharge Requirement (ESD).................

10

10.

EFT/Burst.........................................................................

10

11.

Surge...................................... 10

12.

Burn-In..............................................................................

10

13.

MTBF.................................................................................

10

14.

Dimension

10

Seventeam Electronics Co., Ltd.

ST-550EAG

1. Input Requirements
1-1. Input Voltage
The power supply shall be operated at universal input voltage defined in the following table.
lnput Voltage

MIN

NOM

MAX

Voltage

90

100-240

264

1-2. Frequency
The input frequency range is from 50Hz to 60Hz.

1-3. Inrush Current


The max inrush current is 80A for 115/230VAC.

1-3-1. Cold Start


Conditions

Limits

115/230VAC, full load.


25 ambient.

No component over stress or


damage should occur to the power
supply.
Input fuse shall not blow.

Conditions

Limits

1-3-2. Warm Start

Turn off at 132/264VAC full load No component over stress or


for 1 sec then turn on at the peak damage should occur to the power
of the input voltage cycle at 25 supply.
Input fuse shall not blow.
ambient.

1-4. AC Input Current


AC Input

MAX

Units

115V

12

AMPS

230V

AMPS

Seventeam Electronics Co., Ltd.

ST-550EAG

1-5. Efficiency
The power supply efficiency shall not be less than 68% at the maximum load of sec. 2.2 and 115/230Vac
input voltage.
2. Output Requirements
2-1. Output Regulations
Output
Voltage

Range

MIN

Nominal

MAX

Units

+5V

5%

+4.75

+5.00

+5.25

Volts

+12V1

5%

+11.40

+12.00

+12.60

Volts

+12V2

5%

+11.40

+12.00

+12.60

Volts

-12V

10%

-10.80

-12.00

-13.20

Volts

+3.3V

5%

+3.14

+3.30

+3.47

Volts

+5Vsb

5%

+4.75

+5.00

+5.25

Volts

Note: 1). The above voltage range should also include ripple and noise.
2). The output voltage should be measured at the terminals of output connector.

2-2. DC Load Requirements


Output
Voltage

MIN

NOM

MAX

Units

+5V

1.0

15

30

AMPS

+12V1

1.0

18

AMPS

+12V2

1.0

18

AMPS

-12V

0.0

0.25

0.5

AMPS

+3.3V

0.5

15

30

AMPS

+5Vsb

0.0

AMPS

Note : 1). The maximum continuous total DC output power shall not exceed 550 Watts.
2). The maximum continuous combined load on +5V and +3.3V outputs shall not
exceed 150 Watts.
3). The maximum continuous combined load on +5V, +3.3V and +12V1,+12V2
outputs shall not exceed 535 Watts.

Seventeam Electronics Co., Ltd.

ST-550EAG

2-3. Cross Regulation


The DC loads shall remain within the ranges specified in 2-2 DC Load Requirements and the DC output
voltages also shall remain within the regulation ranges specified in 2-1 Output Regulation when
measured at the load end of the output connectors.
+5V

+3.3V

+12V1

+12V2

-12V

+5VSB

30

18

18

0.5

30

16

16

0.5

15

15

18

0.5

15

15

18

0.5

2-4. +5V standby voltage


The +5Vsb is on whenever the AC power is present.

2-5. DC Output Voltage Ripple and Noise


Output Voltage

Ripple & Noise Max

Units

+5V

50

mV

+12V1

120

mV

+12V2

120

mV

-12V

120

mV

+3.3V

50

mV

+5Vsb

100

mV

Note : 1)The measurements should be made by crossing a 10uF/ electrolytic and a 0.1uF ceramic
disk capacitors at each output with measuring bandwidth from DC to 20 MHz. If ambient
temperature is under 20 or over 30, the AC input should be nominal input.

2-6. Total Output Power


MAX

Units

550

Watts

Seventeam Electronics Co., Ltd.

ST-550EAG

2-7. Remote ON/OFF Control


The power supply outputs shall be enabled with an active-low TTL signal.
When TTL signal is low, the DC outputs are to be enabled.
When TTL signal is high or open circuited, the DC outputs are to be disabled.
Electronic means or a mechanical switch may activate the TTL signal.
After the TTL signal is active high, must wait for 3 seconds before active low again.
2-8. Power Sequence
On

Off

AC IN

T1

T5

PS_ON

+12V
+5V
+3.3V

95%
10%
O/Ps
T2
T3

PG#
T4
T6

2-9. Power On Time (T1)


MAX

Units

500

ms

2-10. Rise Time (T2)


MAX.

Units

20

ms

2-11. Power Good Delay Time (T3)


MIN.

MAX.

Units

100

500

ms

The test environment is 25 condition @ nominal input.


7

Seventeam Electronics Co., Ltd.

ST-550EAG

2-12. Power Good Rise Time (T4)


MAX

Units

10

ms

2-13. Hold Up Time (T5)


MIN.

Units

17

ms

The test environment is 25 & full load condition @ nominal input.

2-14. Power Fail Signal (T6)


Power good signal shall go to a down level 1ms before +5V output voltage falls below the regulation
limits during PS-ON signal pull high.
MIN.

Units

ms

3. Protections
3-1. Over Voltage Protection
When the DC outputs (+5V, +12V1,+12V2, +3.3V) have over voltage condition, the power supply shall
provide latch mode over voltage protection.
DC output

Max

Unit

+12V1,+12V2

15.6

+5V

7.0

+3.3V

4.3

3-2. Short Circuit Protection


A short circuit placed to ground shall cause no damage or power supply shall be shutdown. (The contact
resistance is 0.05 ohm when the outputs short circuit.)

Seventeam Electronics Co., Ltd.

ST-550EAG

3-3. Protection Reset


When the power supply latches into shutdown condition due to a fault on an+5V,+3.3V,+12V1,+12V2
output(OCP, OVP, UVP), the protection shall reset after the fault has been removed, use remote on/off
control or recycle the AC power again for a typical of 3 seconds.

Note+3.3V OCP maximum 150%.+5V OCP maximum 150%.+12V1&12V2 OCP maximum 20A.
3-4. Over Shoot
Any output overshoot at turn on shall be less than 15% of the nominal output value (with resistive load)
as described in sec. 2.1.
3-5. Over Power Protection
At 115/230Vac input the power supply will shut down all DC output within 105% to 150% of full load.

4. Environment
4-1. Operation/Storage Temperature Range
Operation : 0 to 50(nominal input)
Storage : -40 to 70

LOAD
100%
70%

25
4-2. Humidity (none condensing)
Operation: 20% to 85% RH(nominal input)
Storage : 10% to 95% RH

5. Safety
5-1. UL60950-1,
5-2. TUV EN 60950
5-3. SIMKO
5-4. CB

50

Seventeam Electronics Co., Ltd.

ST-550EAG

6. EMI REQUIREMENTS
6-1.CE
6-2.BSMI
6-3.FCC part 15 sub part J class B at system load
6-4.CISPR 22 CLASS B
7. Dielectric Voltage Withstand (HI-POT)
The power supply shall withstand for 3 seconds minute without breakdown the application of an
1800Vac-supply voltage applied between both input line and chassis (10mA AC Cutoff current). Isolating
transformers shall similarly withstand 4242Vdc applied between both primary and secondary windings for
a minimum of one minute.
8. PFC
Active Power Factor Correction, complies with EN 61000-3-2: 1995+A1+A2:1998, Class D.

9. Electrostatic Discharge (ESD)


Comply with IEC 61000-4-2.

10. EFT/ Burst


Comply with IEC 61000-4-4.

11. Surge
Comply with IEC 61000-4-5.

12. Burn-In
Applying 115 Vac 10 % or 230 Vac 10% input voltage and maximum load (80%) for this product in 45
5 chamber.

13. M.T.B.F.
The power supply shall have a minimum mean time between failure greater than 100,000 hours at
continuous operation of 100% load and an ambient temperature of 25 .

14. Dimension.
150(D)X 140(W)X 86(H) mm.

10

Você também pode gostar