Escolar Documentos
Profissional Documentos
Cultura Documentos
Specification
y
Chipset VIA P4X266 for Pentium 4 processors with socket 478 Northbridge: VIA P4X266 and Southbridge: VIA VT8233 Chipset voltage adjustable With active Northbridge-cooler (see illustration on the right) Socket 478 CPU Support Intel Pentium 4 processor (Willamette or Northwood) and P4 Celeron successfully tested with: P4 Celeron up to 1,8 GHz, P4 (Willamette 256KB Cache) up to 2,2GHz and P4 (Northwood 400MHz FSB) up to 2,4GHz with 400MHz FSB (100MHz QuadDatarate-Process) Normally, there is no need to configure the processor. In BIOS the following parameters can be adjusted manually: - FSB-system clock adjustment infinitely from 100 to 132 MHz - Vcore-CPU-voltage from 1,10 to 1,85V - Multiplier 8x to 23x Expansion Slots 1 x AGP Slot supports 4X mode 5 x 32 Bit PCI Onboard IDE Controller 2-Channel Enhanced PCI IDE for up to 4 IDE devices supports UltraDMA/100 incl. ATA-100-cable Optional: IDE RAID Controller (AV40R only) Chip: Promise 265R, supports RAID-modes 0 and 1 (not simultaneously)
with detailed manual and additional ATA-100-cable AV40 without RAID AV40R with RAID
y y
Integrated Audio Function: Software-Audio with AC'97 2.1 conforming CODEC onboard The main work is done by software; the CODEC provides the analog signal Sound-driver for Windows 9x, ME, 2000 and NT 4.0 Connectors on the backpanel: line-in, line-out, microphone, MIDI/gameport More line-ins on the mainboard Audio-in for CD-ROM, TAD and AUX. Backpanel-connectors 1 x PS/2-Mouse 1 x PS/2-Keyboard 1 x Parallel (SSP/EPP/ECP) 2 x Serial (16550 kompatibel, Fifo) 2 x USB (four more onboard) Audio: line-in, line-out, microphone, MIDI/gameport Onboard-connectors 1 x Floppy drive (up to 2,88 MB) 4 x USB (additional) 1 x Infrared (COM2 can be used for infrared communication, IrDA-adapter not included in delivery) 1 x WOL (Wake on Lan) 3 x Fan (CPU, AGP, Chipset) Memory 3 x 184-Pin DIMM-Socket for PC1600 or PC2100 DDR SDRAM memory supports module sizes of 64, 128, 256, 512 and 1024MB with 100 or 133MHz clock frequency up to 1,5 GB capacity Adjustment of DDR-voltage in BIOS possible. Hardware-monitoring CPU-temperature, system voltage and fan revolution can be monitored Power Management ACPI Version 1.0 (Advanced Configuration and Power Interface) supports power saving modes S1 (Snoop), S3 (Suspend to RAM), S5 (Soft-Off) On/Off-button with two functions: Suspend-mode / soft-off BIOS Award V6.0PG PnP Green BIOS 2 MBit Flash EPROM ATX-power supply connector Standard 20-Pin-ATX-power supply connector Addtitional 4-Pin-connector for 12V
Additional 6-Pin-connector for 3,3 and 5V Accessories Mainboard with active Northbridge-cooler, IDE-cable (ATA-100), floppy cable, detailed manual, driver CD-ROM AV40R contains an additional IDE-cable for the onboard IDE RAID-Controller Form Factor ATX: only 30,5 x 24,4 cm
What I need to set in Bios when I'm using SCSI, RAID and IDE HDD devices on AV40R? BIOS
When use SCSI, Raid and IDE HDD devices, firstly please select "First Boot Device from SCSI" then select "RAID & SCSI Boot Order" options in Bios.
If need to disable RAID Bios function via S/W (Bios), please disable "Onboard RAID Boot Rom" option in Bios. Thus upon system boot up it will skip detection step for RAID device. When entering Windows OS still can detect RAID device, you can install the RAID driver for Promise FastTrak but RAID function is unusable since it is disabled in Bios. AV40R does not support H/W disable of RAID Bios function, if required please purchase AV40 (without RAID).
This P4 mainboard uses 20-pin Pentium 4 standard ATX power header (connect to J11)
The ATX power connector is directional and will not go in unless the guides match perfectly making sure that pin#1 is properly positioned. Make sure that the latch of the ATX power connector clicks into place. The power supply must be supplied to ACPI +5V standby power and at least 720mA. Also make sure your P4 power supply have enough power for higher speed processor installed. Please don't connect the power connectors to the mainboard until all other H/W devices has been installed.
No, it does not support ECC memory. AV40/R supports DDR 200/266 compliant SDRAM up to 1.5GB (un-buffered) capacity only. Also supports DDR 200/266 compliant SDRAM up to 3GB (registered) capacity.
1. Disable AGP 4x mode or change to 2x mode in Bios 2. Install O.S. 3. Install VIA 4-in-1 drivers (4.29V or later) 4. Install ATI VGA driver 5. Enter to O.S. 6. Restart the system and go back to Bios Setup to enable AGP 4x mode.
Why cannot use 4 HDDs with RAID O (striping) or RAID 1 (mirroring) function on AV40R?
RAID 0 or RAID 1 function is only supported by the master channel of Promise ATA RAID (Promise PDC20265R chip). The HDD connects to the slave channel of Promise ATA RAID are to be as ATA HDD.
How do I install RAID devices driver during new Windows 2000/XP installation?
Before installing Windows 2000/XP, please extract the Promise IDE RAID driver from our download page to an empty floppy disk. Follow the following procedure to install RAID driver during the initial OS install setup :
y
y y y y y y
2. The message " Press F6 if you need to install a third party SCSI or RAID driver..." will appear at the bottom of the initial OS setup screen. Press <F6> to install RAID driver 3. When the "Windows 2000/XP Setup" window is generated, press "S" to specify an Additional Devices. 4. Press "O" to select "Other" and press the <Enter> key. 5. Insert the Windows 2000/XP RAID driver floppy disk in drive A: and press <Enter> key. 6. Follow the setup menu. 7. If you need to specify any additional devices to be installed, do so at this time. 8. Once all RAID/SCSI devices are specified and respective driver installed continue with Win2000/XP installation.