Escolar Documentos
Profissional Documentos
Cultura Documentos
Installation Manual
Trademarks Windows is a registered trademark of Microsoft Corporation - Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and/or other countries - OpenGL is a registered trademark of Silicon Graphics, Inc. - Wintab is a trademark of LCS/Telegraphics Corporation - Predictor is a registered trademark of Brel&Kjr Sound & Vibration Measurement A/S, Nrum, Denmark Copyright c 2001 . 2009, Brel&Kjr Sound & Vibration Measurement A/S All rights reserved. No part of this publication may be reproduced or distributed in any form, or by any means, without prior written consent from Brel&Kjr Sound & Vibration Measurement A/S, Nrum, Denmark
System requirements
The recommended system requirements of Predictor are: Intel Core 2 Duo Processor 2,8 GHz or better 2 GB of RAM or more Operating system: Windows XP Graphical driver/display: SVGA display or better with Open GL support CD-ROM drive for installation 200 MB of hard-disk space for the Predictor system At least 50 MB of hard-disk space for each Predictor project The digitizer must be either WintabTM compatible or must be able to output coordinates in ASCII stream mode
Digitizers
Digitizers must be able to output the coordinates in ASCII stream mode or must be Wintab compatible. In ASCII stream mode, the digitizer is addressed directly without the need to install a device driver. In that case, the digitizer must be configured in Predictor using the File|Digitizer|Digitizer setup menu option. In the case of a Wintab compatible digitizer, a Wintab device driver must be installed. This driver should be available from the digitizers supplier. For questions concerning the Wintab installation or the digitizer settings, check the digitizer manual or contact your System Manager. As the use of a digitizer can affect the response time of Predictor, this option is by default de-activated. To activate the digitizer option, the following lines need to be added to the file predictor.ini. This file is located in the folder <APPDATA>\Predictor. [Digitiser] Enabled=1 Note: To open this folder select Run from the Windows start-menu and type %APPDATA%\Predictor.
Wintab The Wintab (Windows-based Tablet) specification is an open industry standard software interface specification that was developed in 1991 and has been supported by the members of CAPS (Committee for Advanced Pointing Standards). Wintab provides a consistent interface between applications and tablets from different manufacturers. Predictor supports this standard, as well as many tablet and application manufacturers. For more information concerning Wintab, digitizers, and applications supporting the Wintab standard and links to Wintab drivers see http://www.pointing.com. Note: Predictor automatically checks whether a Wintab driver is installed. If a Wintab driver is not installed, it is not possible to use the File|Digitizer|Digitizer setup menu option.
Printers
Any printer can be used, provided it has a Windows device driver. No special setup is needed. For graphical output, it is important to use the latest printer drivers. If necessary, ask your vendor for new printer drivers. In general, postscript drivers are preferred. Predictor creates graphical output in raster format. Most pen plotters do not support this format. If in doubt, ask your vendor whether your plotter supports raster format.
Licensing
All components are protected by a hardware key in combination with license files. For each hardware key, one or two license files are needed. These license files will be placed in the program folders during the installation. All software need the license file <dongle-id>.lic. This file is only valid for the HASP hardware key with the same identification. It is also possible to name the license file predictor.lic. In this case the installation is only valid for one dongle. If the user multiple licenses, each license needs to be installed in a separate folder. Predictor and the Predictor Calculation Client Pack require a second license file called <dongle-id>.liz, which can also be called lizdat_enduser.liz if only one license is present. The software will only function fully if the hardware key and the required license files are present.
Predictor
Predictor must be installed in a new, empty folder on the local hard disk or network drive. The Predictor installation software will also install SourceDB+; a program for managing sound power levels. Shortcuts can be placed on the desktop and/or in the start menu. Modelling license It is possible to user Predictor in modelling mode. With this option modelling can be done on any computer, the only restriction is that it is not possible to perform calculations, run macros or export results. For this option the file predictor.lic must be present in the program folders, this can be done by making a copy of <dongle-id>.lic and rename it.
Predictor Analyst
Predictor Analyst must be installed in a new, empty folder on the local hard disk or network drive. A shortcut can be placed on the desktop and/or in the start menu.
Acoustic Determinator
Acoustic Determinator must be installed in a new, empty folder on the local hard disk or network drive. A shortcut can be placed on the desktop and/or in the start menu.