Escolar Documentos
Profissional Documentos
Cultura Documentos
Watch your fingers when adjusting clamps. They may become pinched resulting in injury. Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.
Foot Pedal
Kick Pad
[ACCESSORIES] box Cymbal holders (L & R) Drumstick x 2 [DRUM MODULE and HEADPHONES] box Screws x4 for Drum Module Drum module
Cymbal holder
Hexagon Key
Stand
Standard-gauge tubing
Double-Braced Legs
Assembly
1 Open the stand
[A]
[1]Tear off the adhesive tape on the stand. [2] Loosen the wing nuts on the pillars. [3] Open the stand in the order shown in the illustration (A, B, C). [4] Adjust the pillars height so that the stand can locate steadily on the floor. [5] Tighten the wing nuts on the pillars.
Tighten
2 Attaching the tom pads [1] Insert the two tom pads into the side arms respectively. [2] Use a drum key to tighten the screw on the bottom of tom pad. [3] Adjust the side arms height so that it does not interfere with other pads. [4] Tighten the wing nuts on the pillars.
Insert the two tom pads into the side arms respectively.
side arm
Use a drum key to tighten the screw on the bottom of tom pad.
3 Attaching the snare pad [1] Adjust the clamp position, then tighten the wing nuts on the clamp. [2] Use hexagon key to loosen the screw of holder clamp. [3] Insert the metal rod into the holder clamp and adjust the position. [4] Use hexagon key to tighten the screw of holder clamp. [5] Attach the snare pad to the metal rod and adjust the position, then tighten the screw on the snare pad.
use hexagon key to loosen or tighten the screw. insert the metal rod into the lock and adjust the position. attach the snare pad to the metal rod. tighten the screw.
metal rod
4 Attaching the Drum Module [1]Tear off the adhesive tape on the drum module. [2]Place the Drum Module on the drum module holder, and use the included screws to fasten it.
Use a screwdriver Tear off the adhesive tape Use M4x25mm x2 screws Use M4x15mm x2 screws
5 Attaching the cymbal pads [1] Attach the Cymbal holders to the Holder clamps on the arms. [2] Use a drum key to tighten the screws on the Holder clamps. [3] Move out the wing nut and the felt washer of each Cymbal holders. [4] Attach the Cymbal pads to the cymbal holders. [5] Attach the felt washer and wing nut, tighten the wing nut of each cymbal.
attach the cymbal holders to the holder clamps arms. use a drum key to tighten the screws.
Wing nut Felt washer Cymbal holder move out Cymbal holder Wing nut Felt washer Cymbal pad attach and tighten
6 Attaching the Hi-Hat Control pedal [1] Move out the pillar from the rubber foot. [2] Attach the Hi-Hat control pedal to the pillar.
attach the Hi-Hat control pedal to the pillar.
7 Attaching the Kick Trigger [1] Attach the Rod to the holders. [2] Attach the Kick Pedal to the Kick Pad. [3] Tighten the wing screw on the Kick Pedal. [4] Loosen the screw. [5] Attach the Beater to the Kick Pedal [6] Position the Beater from the center of the pedal, tighten the screw
[1]
[3]
[1] [2]
[4] Beater
8 Attaching the Drum Throne [1] Attach the standard-gauge tubing to the round seat. [2] Tighten the wing nut on the round seat. [3] Open the legs. [4] Remove the wing nut and screw attached to the Double-Braced Legs. [5] Attach the standard-gauge tubing to the Double-Braced Legs. [6] Reattach the win nut and screw. [7] Tighten the wing nut and screw.
9 Setup Example
Cymbal Pad
Drum Module
Tom Pad
Cymbal Pad
[4]
[3] [1]
[3]
[5]
Snare Pad
[6],[7] [3]
[2]
Kick Trigger
DD501_Setup_G03_081120