Escolar Documentos
Profissional Documentos
Cultura Documentos
p roduct S peciFicationS
The Goodman brand GKS9 Single-Stage, Multi-Speed Upflow Gas Furnace features a patented aluminized-steel tubular heat exchanger and robust Hot Surface Ignition system. This furnace is run-tested for heating or combination heating/cooling applications. With a corrosion-resistant, painted steel cabinet, this unit can be installed in a variety of locations.
Patented TuffTube dual-diameter tubular heat exchanger Single-stage combination redundant gas valve Hot surface igniter and patented adaptive learning control for long igniter life Quiet, four-speed direct-drive circulator blower motor Furnace control board with self-diagnostics and low-voltage terminal block Dual-certified for sealed combustion direct vent (2-pipe) or non-direct vent (1-pipe) applications Quiet, single-speed induced draft blower All models comply with California NOx emissions standards
Standard Features
up to
92.1% AFuE
upFlow/Multi-poSition
Heating input: 46,000115,000 Btu/H
Foil-faced insulation lines the heat exchanger Designed for upflow installation; can be converted to horizontal left or right with a pressure switch kit (sold separately) Easy-to-install top venting is standard Airtight solid bottom for side return applications and easy-cut tabs for effortless removal in bottom air inlet applications Coil and furnace fit flush for most installations
Cabinet Features
Contents
Nomenclature .................................................................................. 2 Product Specifications .................................................................. 3 Dimensions ....................................................................................... 4 Airflow Specifications .................................................................... 5 Wiring Diagram .................................................................................7 Accessories ........................................................................................ 8
*To receive the Lifetime Heat Exchanger Limited Warranty and 10-Year Parts Limited Warranty, online registration must be completed within 60 days of installation. Online registration is not required in California or Qubec. Full warranty details available at www.goodmanmfg.com.
SS-GKS9
www.goodmanmfg.com
6/09
Supersedes 3/09
SS-GKS9.indd 1
7/6/2009 7:58:54 AM
Product SPecificationS
nomenclature
G 1 K 2 S 3 9 4 70 5,6,7 4 8 B 9 X 10 A 11
Brand G Goodman Brand or Distinctions Airflow Direction C Downflow/Horizontal D Dedicated Downflow H High Airflow K Dedicated Upflow M Upflow/Horizontal
Description V Two-Stage/Variable-speed H Two-Stage/Multi-speed S Single-Stage/Multi-speed E Two-Stage/X-13 Motor AFUE 95 95% 9 90%+ 8 80% 045: 45,000 070: 70,000 090: 90,000 MBTU/h 115: 115,000 140: 140,000
A B C D
Cabinet Width 14 17 21 24
Important EnergyStar Notice: EnergyStar ratings are dependent upon conditions beyond equipment installation. Proper sizing and installation of equipment is critical to achieve optimal performance. Split system air conditioners and heat pumps must be matched with appropriate coil components to meet EnergyStar criteria. Ask your contractor for details or visit www.energystar.gov.
www.goodmanmfg.com
SS-GKS9
SS-GKS9.indd 2
6/8/2009 4:36:52 PM
product SpeciFicationS
SpeciFicationS
GKS9 0453BX* GKS9 0703BX* GKS9 0704CX* GKS9 0904CX* GKS9 0905DX* GKS9 1155DX*
Heating Capacity Input Natural Gas Output LP Gas Output AFUE Available AC @ 0.5 ESP Temperature Rise Range (F) Circulator Blower Size (D x W) Horsepower @ 1075 RPM Speed Vent Diameter No. of Burners Filter Size (in ) Permanent Disposable Electrical Data Min. Circuit Ampacity 4 Max. Overcurrent Device (amps) Ship Weight (lbs)
5 2
Natural Gas BTU/h. For altitudes above 2,000, reduce input rating 4% for each 1,000 above sea level. DOE AFUE based upon Isolated Combustion System (ICS) Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2 or 3 in diameter, depending upon furnace input, number of elbows, length of run and installation (1 or 2 pipes). The optional Combustion Air Pipe is dependent on installation/code requirements and must be 2 or 3 diameter PVC. Vent connector diameter is 2. Refer to the installation & operation manual shipped with the furnace for applicable vent and combustion air pipe lengths. 4 Minimum Circuit Ampacity = (1.25 x Circulator Blower Amps) + ID Blower amps. Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes. 5 Maximum Overcurrent Protection Device refers to maximum recommended fuse or circuit breaker size. May use fuses or HACR-type circuit breakers of the same size as noted. Notes All furnaces are manufactured for use on 115 VAC, 60 Hz, single-phase electrical supply. Gas Service Connection FPT Important: Size fuses and wires properly and make electrical connections in accordance with the National Electrical Code and/or all existing local codes.
SS-GKS9
www.goodmanmfg.com
SS-GKS9.indd 3
6/8/2009 12:43:03 PM
product SpeciFicationS
diMenSionS
A IR D IS C H A R G E
A 2 8 3 /4 3 /4 3 /4 1 9 5 /8 2 1 /2 A IR IN T A K E P IP E 2 " P V C B (D IS C H A R G E ) C V E N T /F L U E P IP E 2 " P V C A IR D IS C H A R G E
A L T E R N A T E G A S S U P P L Y H O L E H IG H V O L T A G E E L E C T R IC A L H O L E 4 0 L E F T S ID E D R A IN L IN E H O L E S 2 3
C O N D D R A w / 3 D IS C (R IG L E F
E N S A T E IN T R A P /4 " P V C H A R G E H T O R T S ID E ) 6 1 /8
S T A N D A R D G A S S U P P L Y H O L E A L T E R N A T E V E N T /F L U E L O C A T IO N H IG H V O L T A G E E L E C T R IC A L H O L E R IG H T S ID E D R A IN L IN E H O L E S
1 4
L O W V O L T A G E E L E C T R IC A L H O L E S ID E C U T -O U T
2 3 /4
L O W V O L T A G E E L E C T R IC A L H O L E
U N F O L D E D F L A N G E S 2 2 1 /1 6 F O L D E D F L A N G E S 2 3 9 /1 6 L E F T S ID E V IE W
U N F O L D E D F L A N G E S D F O L D E D F L A N G E S E F R O N T V IE W R IG H T S ID E V IE W W IT N E S S M A R K S F O R S ID E C U T -O U T
A 17 17 21 21 24 24
B 16 16 19 19 23 23
C 13 13 16 16 20 20
D 12 12 16 16 19 19
E 13 13 17 17 20 20
Notes: Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2 or 3 in diameter, depending upon furnace input, number of elbows, length of run and installation (1 or 2 pipes). The optional Combustion Air Pipe is dependent on installation/code requirements and must be 2 or 3 diameter PVC. Line voltage wiring can enter through the right or left side of the furnace. Low voltage wiring can enter through the right or left side of furnace. Conversion kits for high altitude natural gas operation are available. Contact your Goodman distributor or dealer for details. Installer must supply following gas line fittings, according to which entrance is used: LeftTwo 90 elbows, one close nipple, straight pipe RightStraight pipe to reach gas valve For bottom return: Failure to unfold flanges may reduce airflow by up to 18%. This could result in performance and noise issues.
C = If placed on combustible floor, the floor MUST be wood ONLY. Notes: For servicing or cleaning, a 24 front clearance is recommended. Unit connections (electrical, flue and drain) may necessitate greater clearances than the minimum clearances listed below. In all cases, accessibility clearance must take precedence over clearances from the enclosure where accessibility clearances are greater.
www.goodmanmfg.com
SS-GKS9
SS-GKS9.indd 4
6/8/2009 12:43:03 PM
product SpeciFicationS
airFlow SpeciFicationS
(CFM & Temperature Rise vs. External Static Pressure) Motor Speed High Med GKS9 0453BX* Med-Lo Low High Med GKS9 0703BX* Med-Lo Low High Med GKS9 0704CX* Med-Lo Low High Med GKS9 0904CX* Med-Lo Low High Med GKS9 0905DX* Med-Lo Low High Med GKS9 1155DX* Med-Lo Low Tons AC at 0.5 ESP 3 2.5 2 1.5 3 2.5 2 1.5 4 3.5 3 2.5 4 3.5 3 2.5 5 4 3.5 3 5 4 3.5 3 External Static Pressure, (Inches Water Column) 0.1 CFM 1,352 1,214 997 757 1,449 1,192 981 750 2,069 1,752 1,437 1,184 1,970 1,713 1,439 1,183 2,147 1,675 1,489 1,307 2,134 1,678 1,453 1,259 Rise 29 32 40 52 41 50 61 79 29 34 41 50 40 46 55 67 37 47 53 61 46 58 68 78 0.2 CFM 1,318 1,172 994 753 1,409 1,172 962 730 1,965 1,724 1,437 1,177 1,874 1,650 1,412 1,155 2,114 1,686 1,470 1,265 2,103 1,643 1,440 1,239 Rise 30 34 40 52 42 51 62 81 30 34 41 50 42 48 56 69 37 47 54 63 47 60 68 79 0.3 CFM 1,260 1,123 960 734 1,326 1,141 943 714 1,871 1,667 1,417 1,161 1,757 1,572 1,370 1,122 2,057 1,640 1,436 1,234 2,029 1,643 1,426 1,220 Rise 31 35 41 54 45 52 63 83 32 36 42 51 45 50 58 71 39 48 55 64 48 60 69 80 0.4 CFM 1,202 1,064 923 704 1,273 1,094 917 692 1,756 1,603 1,369 1,132 1,667 1,510 1,327 1,108 2,030 1,623 1,409 1,203 1,941 1,577 1,363 1,181 Rise 33 37 43 56 47 54 65 86 34 37 43 52 48 52 60 72 39 49 56 66 51 62 72 83 0.5 CFM 1,128 1,012 884 674 1,201 1,046 888 657 1,661 1,488 1,320 1,095 1,566 1,418 1,260 1,062 1,978 1,557 1,361 1,168 1,906 1,527 1,349 1,159 Rise 35 39 45 59 49 57 67 90 36 40 45 54 51 56 63 75 40 51 58 68 51 64 73 85 0.6 CFM 1,044 938 817 620 0.7 CFM 955 859 741 524 0.8 CFM 853 741 611 438 Model
1,194 1,136 1,018 973 830 620 904 764 570 793 665 502
1,549 1,415 1,275 1,402 1,290 1,082 1,256 1,140 1,047 928 984 837
1,431 1,334 1,182 1,313 1,211 1,079 1,166 1,078 1,011 931 956 816
1,889 1,784 1,713 1,501 1,455 1,360 1,318 1,243 1,130 1,096 1,053 991
1,818 1,733 1,625 1,489 1,423 1,339 1,314 1,253 1,205 1,118 1,082 1,015
Notes: CFM in chart is without filter(s). Filters do not ship with this furnace, but must be provided by the installer. If the furnace requires two return filters, this chart assumes both filters are installed. All furnaces ship as high-speed cooling and medium-speed heating. Installer must adjust blower cooling and heating speed as needed. For most jobs, about 400 CFM per ton when cooling is desirable. INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPECIFIED ON THE RATING PLATE. The chart is for information only. For satisfactory operation, external static pressure should not exceed value shown on the rating plate. The above chart is for U.S. furnaces installed at 0-2000 feet. At higher altitudes, a properly de-rated unit will have approximately the same temperature rise at a particular CFM, while ESP at the CFM will be lower.
SS-GKS9
www.goodmanmfg.com
SS-GKS9.indd 5
6/8/2009 12:43:04 PM
TEMPERATURE RISE
SS-GKS9.indd 6
product SpeciFicationS
100
600 CFM 700 800 900 1000 1100 1200 1400 1600 1800 2000 2200 2400 CFM
90
80
70
60
www.goodmanmfg.com
50
40
30 FORMULAS
BTU OUTPUT = CFM x 1.08 x RISE BTU OUTPUT RISE = CFM 1.08
20
30
40
13
SS-GKS9
6/8/2009 12:43:04 PM
product SpeciFicationS
wiring diagraM
24 VAC HUMIDIFIER
OR GY 40 VA TRANSFORMER
BK
WH
G Y W TO MICRO
OR
FUSE
3 2 5 8 11 1 4 7 10
BL PK OR BL YL GR
GY
6 9 12
GY RD
OR BR
TH (3)
MANUAL RESET ROLLOUT LIMIT CONTROL(S) (SINGLE CONTROL ON 45K BTU) 24 VAC 40 VA TRANSFORMER
WH
XFMR-H
DIAGNOSTIC LED
2 1
WH
GND WH
SEE NOTE 4
LINE-H
BK
INTEGRATED CONTROL MODULE
RD
PK
IND
CO OL
ID BLWR
BR
CIRCULATOR BLWR
A HE T-H
BK
CAPACITOR
PU BLOWER COMPARTMENT BURNER COMPARTMENT GND BK WH INDUCED DRAFT BLOWER AUTO RESET PRIMARY LIMIT CONTROL BL YL RD OR
N O C
WH
WH PU
WARNING: DISCONNECT POWER BEFORE SERVICING. WIRING TO UNIT MUST BE PROPERLY POLARIZED AND GROUNDED.
L GND N
DISCONNECT
PK MANUAL RESET ROLLOUT LIMIT CONTROL(S) ( SINGLE CONTROL ON 45K BTU ) GND BR
NO C
RD
WH ID BLOWER 24 VAC PRESSURE HUMIDIFIER SWITCH 2 CIRCUIT CONNECTOR HOT SURFACE IGNITER BL GR WH
JUNCTION BOX
WARNING:DISCONNECT POWER BEFORE SERVICING.WIRING TO UNIT MUST BE PROPERLY POLARIZED AND GROUNDED.
C2
N GND
MI
GAS VALVE
BK
L DISCONNECT
STEADY ON = NORMAL OPERATION OFF = CONTROL FAILURE = SYSTEM LOCKOUT (RETRIES EXCEEDED) 1 FLASH
LOW VOLTAGE (24V) LOW VOLTAGE FIELD HI VOLTAGE (115V) HI VOLTAGE FIELD
1 2 3 4 5 6 C
2 FLASHES = PRESSURE SWITCH STUCK CLOSED 3 FLASHES = PRESSURE SWITCH STUCK OPEN 4 FLASHES = OPEN HIGH LIMIT 5 FLASHES = FLAME SENSE WITHOUT GAS VALVE 6 FLASHES = OPEN ROLLOUT CONTINUOUS/RAPID FLASHES = REVERSED 115 VAC POLARITY
JUNCTION TERMINAL INTERNAL TO INTEGRATED CONTROL PLUG CONNECTION IGNITER SWITCH (PRESS.) OVERCURRENT PROT. DEVICE
NOTES: 1. SET HEAT ANTICIPATOR ON ROOM THERMOSTAT AT 0.7 AMPS. 2. MANUFACTURER'S SPECIFIED REPLACEMENT PARTS MUST BE USED WHEN SERVICING. 3. IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE FURNACE MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL HAVING A TEMPERATURE RATING OF AT LEAST 105 C. USE COPPER CONDUCTORS ONLY. 4. IF HEATING AND COOLING BLOWER SPEEDS ARE NOT THE SAME, DISCARD JUMPER BEFORE CONNECTING BLOWER LEADS. UNUSED BLOWER LEADS MUST BE PLACED ON "PARK" TERMINALS OF INTEGRATED CONTROL OR TAPED. 5. UNIT MUST BE PERMANENTLY GROUNDED AND CONFORM TO N.E.C. AND LOCAL CODES.
0140F00236 REV. C
SS-GKS9
www.goodmanmfg.com
Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring
WARNING
OR
High Voltage: Disconnect all power before servicing or installing this unit. Multiple power sources may be present. Failure to do so may cause property damage, personal injury, or death.
BK BK
XFMR-H
PK GR RD YL WH GY
LINE NEUTRALS
WH
BL OR
OR BR
SS-GKS9.indd 7
6/8/2009 12:43:06 PM
product SpeciFicationS
acceSSorieS
Accessory LPT-00A LPLP01 HALP10 HANG11 HANG12 Description LP Conversion Kit LP Gas Low Pressure Kit High-Altitude LP Gas Kit High-Altitude Natural Gas Kit High-Altitude Natural Gas Kit GKS9 GKS9 GKS9 GKS9 GKS9 GKS9 0453BX* 0703BX* 0704CX* 0904CX* 0905DX* 1155DX* 3 1 2 -------- 3 1 2 -------- 3 1 2 -------- 3 1 2 -------- 3 1 2 -------- 3 1 2 --------
017K000005 Flush-Mount Vent Kit 0270K00012 Horizontal Conversion Pressure Switch Kit AFE18-60A FTK-03A GSAS GMU EFR01 DCVK-20 DCVK-30 Fossil Fuel Kit Twinning Kit Electronic Air Cleaner Media Air Cleaner External Filter Rack 2 Horizontal/Vertical Concentric Vent Kit 3 Horizontal/Vertical Concentric Vent Kit
tHerMoStatS
Model CHT18-60 CH70TG CHSATG H20TWR Description Cooling/Heating, Mechanical Cooling/Heating, Digital, Non-programmable Cooling/Heating, Mechanical Heating Only, Mechanical
Goodman Manufacturing Company, L.P., reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. 2008-2009 Goodman Manufacturing Company, L.P. Houston, Texas Printed in the USA.
www.goodmanmfg.com
SS-GKS9
SS-GKS9.indd 8
6/8/2009 12:43:06 PM