Escolar Documentos
Profissional Documentos
Cultura Documentos
The SN54 / 74LS240, 241 and 244 are Octal Buffers and Line Drivers designed to be employed as memory address drivers, clock drivers and bus-oriented transmitters/receivers which provide improved PC board density.
Hysteresis at Inputs to Improve Noise Margins 3-State Outputs Drive Bus Lines or Buffer Memory Address Registers Input Clamp Diodes Limit High-Speed Termination Effects
LOGIC AND CONNECTION DIAGRAMS DIP (TOP VIEW) SN54 / 74LS240
VCC 2G 20 19 1Y1 18 2A4 1Y2 17 16 2A3 15 1Y3 2A2 1Y4 14 13 12 2A1 11
20 1
20
1 1G
2 1A1
6 1A3
10 GND
SN54 / 74LS241
VCC 2G 20 19 1Y1 18 2A4 1Y2 17 16 2A3 15 1Y3 2A2 1Y4 14 13 12 2A1 11
20 1
ORDERING INFORMATION
SN54LSXXXJ Ceramic SN74LSXXXN Plastic SN74LSXXXDW SOIC
1 1G 2 1A1 3 4 5 6 1A3 7 8 9 10 GND 2Y4 1A2 2Y3 2Y2 1A4 2Y1
SN54 / 74LS244
VCC 2G 20 19 1Y1 18 2A4 1Y2 17 16 2A3 15 1Y3 2A2 1Y4 14 13 12 2A1 11
1 1G
2 1A1
6 1A3
10 GND
SN54 / 74LS244
INPUTS OUTPUT
SN54 / 74LS241
INPUTS 1G L L H D L H X OUTPUT 2G L H (Z) H H L D L H X L H (Z) INPUTS OUTPUT
VCC = MAX, VOUT = 2.7 V VCC = MAX, VOUT = 0.4 V VCC = MAX, VIN = 2.7 V VCC = MAX, VIN = 7.0 V VCC = MAX, VIN = 0.4 V VCC = MAX
Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.
AC WAVEFORMS
VIN
1.3 V tPLH
VCC
VOUT
1.3 V
RL
Figure 1
SW1
VIN
1.3 V tPHL
VOUT
1.3 V
SW2
Figure 2
VE VE
1.3 V tPLZ
SWITCH POSITIONS
1.3 V
VOL
VOUT
0.5 V
Figure 3
Figure 5
VE 1.3 V VE tPZH VOUT 1.3 V 1.3 V tPHZ VOH 0.5 V
1.3 V
Figure 4
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: MILLIMETER. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
-B1 10
0.25 (0.010)
5.
10 PL
G R X 45 -TC K
M
SEATING PLANE
M D 20 PL
0.25 (0.010) T B
S
DIM A B C D F G J K M P R
10.05 0.25
10.55 0.75
0.395 0.010
0.415 0.029
20 1
11
2.
10
3.
B A F C L
N H D
SEATING PLANE
J M
DIM A B C D F G H J K L M N
7.62 BSC 0
15
0.300 BSC 0
15
0.25
1.02
0.010
0.040
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. 3. CONTROLLING DIMENSION: INCH. DIMENSION L" TO CENTER OF LEAD WHEN FORMED PARALLEL.
B C L
4.
5.
-TSEATING PLANE
K E G F D 20 PL
0.25 (0.010)
M
M J 20 PL
0.25 (0.010) T A
M M
DIM A B C D E F G J K L M N
7.62 BSC 0
15
0.300 BSC 0
15
0.51
1.01
0.020
0.040
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. tPZH Open Closed EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. tPZL Closed Open ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
SYMBOL
SW1
SW2
tPLZ
Closed Closed
Closed Closed
tPHZ
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.