Escolar Documentos
Profissional Documentos
Cultura Documentos
Objectives
At the end of this module the participants will be able to:
Explain the procedure to set up Iub by using OMS. List the ATM resources required for connecting a WBTS by an
Iub interface. Explain the structure of the RNW database of an RNC.
Iub Integration
Set up Iub 1. Configure of physical interfaces
2. Creation of ATM for control and user plane 3. Creation of Connection Configuration (CoCo) for control and user plane 4. Creation of Radio Network objects (WBTS, WCELL, HOP, FMC and ADJ)
End
MML
Step 4
AXC IP router
WAM T T P
VPC
AAL5 TP AAL2 TP
WAM T T P
AAL5 TP AAL2 TP
ATM IF/VPI/VCI
COCO
VPLtp VCLtp
COCO
RNC Database
RNC
WBTS
FMCS
ADJS
ADJI
ADJG
WRAB
8 Nokia Siemens Networks RN33016EN10GLA0_Radio Network Integration and Expansion
Application Launcher
Start Application Launcher
NE: OMS IP address Login: Nemuadmin Password: nemuuser
Read/modify WBTS
object settings
Read/modify HOPS
object settings
Read/modify FMC
object settings
Read/modify COCO
object settings
10
RNC Object
11
Note: Once the RNC ID has been selected and confirmed it can not be changed.
RNC Object
12
13
14
15
IUCS Object
16
Note: if the RNC is to be integrated in Rel. 99 core network, than the SPC of the MGW would be configured. If the RNC is to be integrated in Rel.4 core network, the SPC of MSS would be configures.
IUPS Object
17
IUR Object
18
COCO Object
Create phyTTP and ATM Interface for Iub by using MML
commands.
COCO Object
Check to use automatic calculation by
the system of Cell Delay Variation Tolerance
creation. This parameter defines if the termination points are created during the COCO object creation
20
COCO Object
Create CNBAP links
Define CNBAP
TP ID and PCR
21
COCO Object
Create AAL2SIG links Define AAL2SIG link
ID, IF/VPI/VCI and PCR
Define AAL2UP
22
NOTE: A2EA and AAL2 path ID generation mode should be the same as configured in WBTS. AAL2 End Address and AAL2 path ID are calculated automatically by the system. AAL2MUX should be enabled if used in Iub.
NOTE: As soon as a CoCo object is linked to a WBTS the system shows the state of signalling links and ICSU unit index that are used.
COCO Object
AAL2UP link data Define AAL2UP usage,
Path Type, A2EA generation mode
23
NOTE: A2EA and AAL2 path ID generation mode should be the same as configured in WBTS. AAL2 End Address and AAL2 path ID are calculated automatically by the system. AAL2MUX should be enabled if used in Iub.
NOTE: As soon as a CoCo object is linked to a WBTS the system shows the state of signalling links and ICSU unit index that are used.
24
25
WBTS Object
Click to
select view
Click to add
new WCELL
parameters
WBTS Object
Define WBTS ID Set WBTS name Select COCO ID or
CNBAP link ID ID/CNBAP ID
27
WBTS Object
28
WCEL Object
Define Local Cell Resource ID Define Cell ID Define LAC, SAC, RAC Select UTRA Absolute
Frequency Channel number (UARFCN)
Define primary DL scrabbling code Select Cell range Select frame timing offset of a cell Select Circuit and Packet
Switched core networks
29
WCEL Object
Select UTRAN
Registration Area ID
30
31
32
33
34
WRAB Object
35
36
IPQM Object
37
IPNB Object
38
TQM Object
39