Escolar Documentos
Profissional Documentos
Cultura Documentos
VALVES
ASME Class 150 - 2500
50mm - 1200mm (2 - 48)
The AIL Cast Steel Gate, Globe and Check Valves have established themselves the world over for their quality, reliability and long service. The valves are manufactured to the latest international designs, using advanced manufacturing techniques and stringent quality control checks. The valves are regularly supplied to major international clients including oil refining companies and EPC contractors. A wide network of distributors ensures that availability of AIL valves anywhere in the world.
Table of Contents
AUDCO INDIA LIMITED (AIL) is a leading valve manufacturer, with a strong presence in India and overseas.
Content Page No.
Introduction
02 - 05
03 04 04 05 05
AIL has three manufacturing facilities located in Southern India. The main plant is located in Manapakkam, Chennai. The two other plants are at Maraimalai Nagar, 40 kilometres south and at Kancheepuram, 70 kilometres west of the main plant. The plants are equipped with modern manufacturing facilities with special-purpose machines, automatic welding equipment, heat treatment furnaces and testing equipment for total control of all manufacturing operations. In-house metallurgical and NDE laboratories, and calibration facilities with modern equipment provide support to ensure the quality of products manufactured.
Manufacturing Program ..................................................... Test / Inspection methods & acceptance criteria .............. Test Pressures for Standard Carbon Steel Valves ............ Compliance Standards ..................................................... Body / Bonnet Materials ...................................................
06 - 15
Salient Features ...............................................................06, 07 Trim Material ..................................................................... 08 Stem Packing .................................................................... 08 Bonnet Gaskets ................................................................ 08 Ordering Information ......................................................... 09 Gate Valves (Cl 150, 300 & 600) ....................................... 10 Gate Valves (Cl 900 & 1500) ............................................. 11 Globe Valves (Cl 150, 300 & 600) ..................................... 12 Globe Valves (Cl 900 & 1500) ........................................... 13 Check Valves (Cl 150, 300 & 600) .................................... 14 Check Valves (Cl 900 & 1500) .......................................... 15
16 & 17
Salient Features ................................................................ 16 Stainless Steel Gate Valves (Cl 150 & 300) ...................... 17
AIL manufactures a wide variety of industrial valves. The Quality Management System in all three plants is certified to ISO 9001 System.
AIL Cryogenic Valves AIL Special Valves AIL Valve Accessories Technical Information
22 & 23 24 25 26 - 29
Pressure-Temperature Ratings ........................................ 26, 27 End Flange Dimensions-Cl 150 & 300 - RF ..................... 28 Large-size End Flange Dimensions - Cl 150 & 300 - RF 28 End Flange Dimensions-Cl 600 - RF / RTJ ...................... 28 End Flange Dimensions-Cl 900 - RF / RTJ ...................... 28 End Flange Dimensions-Cl 1500 - RF / RTJ .................... 28 Butt-weld end details and dimensions .............................. 29 Cast Steel - Material Characteristics ................................ 29
30 31
02
Introduction
Quality Policy
It is the policy of AUDCO INDIA LIMITED to Adopt recognized standards for quality systems Maintain a high standard of quality consistent with customer requirements Comply with the codes and standards or customer specifications, applicable to the products and services offered
Q
l l
Valve type
End Conn.
ASME 1 Class 2 2 /2 3 4 5 6 8 10 12 14 16 18 20 24 28 30 34 36 42 48
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l
150 300 Flanged 600 Gate Valves 900 Bolted Bonnet 1500 Flex Wedge 150 Buttweld 300 600 ends 900 1500 150 300 Flanged 600 Globe Valves 900 Bolted Bonnet 1500 150 Plug/Ball type 300 Disc Buttweld 600 ends 900 1500 150 300 Flanged 600 900 Check Valves 1500 Bolted Cover 150 Swing type Disc Buttweld 300 600 ends 900 1500 Gate Valves 150 Bolted Bonnet Flanged 300 Gate Valves 900 Buttweld Pr. Seal Bonnet 1500 ends Parallel Slide Disc 2500 Globe Valves 900 Buttweld Pr. Seal Bonnet 1500 ends Plug type Disc 2500 Check Valves 900 Buttweld Pr. Seal Bonnet 1500 ends Swing type 2500 150 Cryogenic 300 Gate Valves 600 150 Cryogenic 300 GlobeValves 600 150 Soft-seated 300 Gate Valves 600 150 300 Live Loaded 600 Gate / Globe 900 Valves 1500
T H I C K N E S S
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l
l l l l l l l l l l l l l l l l l l l l l l l l l
W A L L
l l l
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l
&
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l
l l l l l l l l l l l l
l l l l l l l l l l l l l l l l l
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l
V A L V E S
CRYOGENIC
l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l
O T H E R
SPECIALS
03
Introduction
Method
Acceptance Criteria
MSS SP55 Relevant ASTM Relevant ASTM ASME B16.34 ASME B16.34 ASME B16.34 ASME B16.34 API 598/BS 6755 Part I Valve Standard
The pressure containing parts of all valves are marked with the foundry identification and heat numbers. Valve test certificates provide the correlating heat numbers along with chemical analysis and mechanical properties of these parts.
7 (100)
Low Pressure Test for Swing Check Vlaves In addition to the high pressure closure test, Swing Check Valves are subjected to low pressure hydrostatic closure test at a pressure of 25% of the high pressure closure test. The duration of the test is the same as that of the high pressure closure test.
04
Introduction
Compliance Standards
Parameter
API 600 Gate Valve Globe Valve Check Valve API 603 Gate Valve ASME B16.34 Gate, Globe, Check Valves Pressure-Temperature rating Face-to-face / End-to-end dimension End Flange dimensions Butt-weld End dimensions Valve Inspection & Testing
Compliance
API 600 BS 1873* BS 1868* API 603 ASME B16.34 ASME B16.34 ASME B16.10 ASME B16.5** ASME B16.25 API 598
AIL has the distinction of having obtained a number of international approvals. Notable among these are :
l l
ISO 9001-certified Quality Management System Certified to use CE marking for supply to the European Union Specific company approvals from international oil majors and EPC contractors
The valves also comply with applicable BS specifications. * Shell wall thickness as per API 600 ** For valves larger than 24 (600mm), the flange drilling shall be as per ASME B16.47 Series A (MSS SP 44) or Series B (API 605). RTJ flanges are offered as optional for Class 600 and above.
Material Classification
Carbon Steel 11/4 Cr - 1/2 Mo 21/4 Cr - 1 Mo 5 Cr - 1/2 Mo 9 Cr - 1 Mo 9 Cr - 1 Mo - /4 V Low-temperature Steel Austenitic Stainless Steel 18-8 (Type 304) Austenitic Stainless Steel 16Cr - 12Ni - 2 Mo (Type 316)
1
ASTM Specification
ASTM A216 Gr. WCB ASTM A217 Gr. WC6 ASTM A217 Gr. WC9 ASTM A217 Gr. C5 ASTM A217 Gr. C12 ASTM A217 Gr. C12A ASTM A352 Gr. LCB/LCC ASTM A351 Gr. CF8 ASTM A351 Gr. CF8M
Working temperature*
-290C to 4270C (-200F to 8000F) -290C to 5930C (-200F to 11000F) -290C to 5930C (-200F to 11000F) -290C to 6490C (-200F to 12000F) -290C to 6490C (-200F to 12000F) -290C to 6490C (-200F to 12000F) -460C to 3430C (-500F to 6500F) -1960C to 6490C (-3200F to 12000F) -1960C to 6490C (-3200F to 12000F)
Other materials such as ASTM A351 Gr. CF3 and ASTM A351 Gr. CF3M are also offered.
* ASME pressure-temperature ratings on pages 26 & 27. Bolting & trim materials will influence the working temperature.
05
Body and Bonnet The body and bonnet are cast with uniform section and generous radius fillets to prevent stress concentration. The castings are precision-machined for high performance.
Circular Joint
The gate valve body has a straight through port without recesses except at the seat area. This ensures minimum turbulence, erosion and resistance to flow. Long integral guide ribs in the body match with guide slots in the wedge for accurate alignment and guidance. Bonnet castings are of one-piece design, where the yoke is integral with the bonnet for gate valves of sizes up to 12 (300mm). This ensures accurate alignment of stem and a smooth operation.
Back Seat In AIL gate and globe valves, a precisionmachined back-seat bush is threaded in the bonnet and is secured by a tab-weld.
tab tab weld
In globe valves of larger sizes and for higher pressure classes of ASME Class 900 and above, the internal part of the body is machined to provide continuous guiding of the disc from the open to the closed position.
Flexible Wedge AIL gate valves feature a one-piece cast flexible wedge that minimises stress concentration. Wedge flexibility ensures tight seating over a wide range of differential pressures and temperatures. It also adjusts to slight misalignments caused by pipeline deflections and thermal deformation. The stem-to-wedge thrust is applied close to the wedge centre. This reduces lateral stem loading and provides for more accurate wedge movement.
The check valve body provides a full port without pockets from inlet to the valve seat. On the downstream side, the body has generous proportions to facilitate full swing of the disc to reduce disc erosion and flow resistance.
06
Ball-type Disc AIL globe valves feature a ball-type disc that provides a fine grain surface on the taper seat. For severe services that demand hard-faced seats, a plug-type disc is provided.
Yoke Sleeve and Yoke Bush Cast in austenitic, copper-free ductile iron alloy to provide resistance to heat, corrosion and wear, the Yoke Sleeve in gate valves features a long thread engagement that assures accurate alignment of the stem. Moreover, it can be removed without replacing the bonnet. In gate valves of sizes 150mm and higher in Class 600 rating and above, the yoke sleeve is mounted on thrust bearings to facilitate easy operation. The Yoke Bush of globe valves is also made from ductile iron alloy, and has a long thread engagement for accurate stem alignment. In Class 900 and 1500 ratings, the valves have a yoke sleeve to facilitate smooth operation.
Swing-type Disc Assembly The one-piece construction is securely fastened to the hinge by means of a lock nut and pin. The disc is free to rotate to avoid localized wear. The hinge pin offers excellent wear resistance properties.
Seat Ring AIL gate valves and check valves feature a seal-welded seat ring that offers a leakproof design as it eliminates the leakage path betwen the seat ring and the body. This design is superior to screwed seats which can loosen up due to temperature fluctuations, corrosion or vibration and result in leakage. For 50mm gate valves, the seat ring is flared into the body, while seal welding is optional. AIL globe valves feature a shoulder type, threaded body seat ring which has a wide taper area that provides for ample seating. Slots on the seat ring allow easy in-situ removal for servicing. Threaded seat rings are secured by a tab-weld. Welded seat rings are also availble in AIL Globe Valves
Stuffing Box The machined stuffing box chamber with a flat bottom allows correct sealing of the gland packing. Surface finish is controlled to required limits, to ensure low-emission performance. Stuffing boxes are provided with five numbers of gland packing to achieve correct compression of all packings and to ensure tight sealing. Valves in Class 300 rating and above feature a provision for a lantern ring arrangement for conditions that demand that there be no leakage of service fluid to the atmosphere. The lantern ring has a leakoff plug which allows connection for liquid or grease seal. See page 25 for more details on lantern ring.
Stem AIL gate and globe valves feature a stem of one-piece construction, ACME threaded and precision-machined with polished surfaces to reduce friction, minimise leakage and extend stem life. In gate valves, the heavy forged T-head engages with the T-slot in the wedge. The stem also has an integral self-adjusting radial back-seat shoulder that matches with the back-seat bush in the bonnet. In globe valves, the stem is held to the disc by a stem nut that permits the disc to swivel. This free-floating design ensures uniform seating.
Flange Drilling and Facing finish The standard range of AIL flanged valves in sizes of up to 24 (600mm) is finished with end-flanges faced, drilled and spot-faced (or backfaced) to ASME B16.5 Raised Face (RF). Flanges in valves of sizes larger than 24 (600mm) are drilled as per ASME B16.47 Series A (MSS SP 44) or Series B (API 605). Valves in ASME Class 600 and above are offered with RTJ end flanges on request. The standard finish offered on the raised faces is 125-250 microns in Ra (AARH) Spiral Serration. Other finishes can be offered on request.
07
Trim Material
AIL Trim No.
1 2 5 8 9 10 12 16
Stem Packing
Stem
13% Cr. SS 316 13% Cr. 13% Cr. Monel SS 316 SS 316 SS 316
Max. temp.
6490C (12000F)
2040C (4000F)
@AIL Trim No. 16 will feature a back-seat of either SS 316 or SS 316 + HF* * HF : Hard-faced with Stellite #6 (Co-Cr-W alloy) or equivalent. Trim 12 valves comply with NACE MR0175 for hardness and heat treatment requirements of wetted components. Trim 8 valves can also be offered for NACE service on request.
Bonnet Gaskets
Valve Type ASME Class
150
Typical
Graphite Gasket with SS 316 insert Spirally-wound SS 304 with Graphite filler
Optional
Spirally-wound SS 304 / SS 316 with PTFE filler Spirally-wound SS 316 with Graphite filler Spirally-wound SS 304 / SS 316 with PTFE filler Octagonal Ring Type (RTJ) metal gasket in Soft Iron Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Spirally-wound SS 316 with Graphite filler Spirally-wound SS 304 / SS 316 with PTFE filler Octagonal Ring Type (RTJ) metal gasket in Soft Iron Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Spirally-wound SS 316 with Graphite filler Spirally-wound SS 304 / SS 316 with PTFE filler Octagonal Ring Type (RTJ) metal gasket in Soft Iron Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316 Octagonal Ring Type (RTJ) metal gasket in SS 304 / SS 316
300
Gate
600 Spirally-wound SS 304 with Graphite filler Octagonal Ring Type (RTJ) metal gasket in Soft Iron Octagonal Ring Type (RTJ) metal gasket in Soft Iron Spirally-wound SS 304 with Graphite filler
Globe
600 Spirally-wound SS 304 with Graphite filler Octagonal Ring Type (RTJ) metal gasket in Soft Iron Octagonal Ring Type (RTJ) metal gasket in Soft Iron
900 1500
150 300
Check
600
Spirally-wound SS 304 with Graphite filler Octagonal Ring Type (RTJ) metal gasket in Soft Iron Octagonal Ring Type (RTJ) metal gasket in Soft Iron
900 1500
08
Ordering Information
Valve Size mm (in)
50 (2) 65 (21/2) 80 (3) 100 (4) 125 (5) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) 450 (18) 500 (20) 600 (24) 700 (28) 750 (30) 850 (34) 900 (36) 1050 (42) 1200 (48)
As a standard, AIL Valves are made in Carbon Steel to ASTM A216 Gr. WCB. For valves in other materials and for accesories like gear operation and electrical actuators, suffix suitable abbreviations to the above ordering code such as : WC6 for ASTM A217 Gr. WC6 WC9 for ASTM A217 Gr. WC9 LCB for ASTM A352 Gr. LCB LCC for ASTM A352 Gr. LCC C5 for ASTM A217 Gr. C5 C12 for ASTM A217 Gr. C12 GO for Gear Operation LA for Locking Arrangement E for Electrical Actuator EB for Extended Bonnet (Cryogenic valves) ES for Extension Spindle
Valve Type
End Connection
3 Flanged RF 5 Flanged RTJ 6 Butt-weld 1 2 5 8 9
Trim Number
10 12 16
09
Description
Body Body Seat Ring Wedge Stem Gasket - Cl.150 Gasket - Cl.300 & 600 Bonnet Stud Stud Nut Back-seat Bush Packing Gland Gland Flange
Material
ASTM A216 Gr. WCB ASTM A105 + HF* ASTM A216 Gr. WCB + 13% Cr. Steel ASTM A182 Gr. F6a ASTM A308 Spirally-wound SS 304 with graphite filler ASTM A216 Gr. WCB ASTM A193 Gr. B7 ASTM A194 Gr. 2H 13% Cr. Steel Graphite with braided end rings Steel ASTM A105 / ASTM A216 Gr. WCB Cr. - Mo Steel ASTM A194 Gr. 2H Steel ASTM A439 Type D2 Steel
Eye Bolt Eye Bolt Nut Groove Pin Yoke Sleeve (Stem Nut) Grease Fitting Retainer Nut Steel / Ductile Iron / Handwheel Malleable Iron Handwheel Nut Nameplate SS 304 * HF - Hard-Faced with Stellite #6 or equivalent For other body / bonnet materials, refer page 5
Approx.Wt. B/W
292 356 432 559 660 787 838 889 991 1092 1194 1397 -
B
376 480 480 584 750 790 996 1191 1399 1539 1714 1956 2159 2565 3160 3429 3650 3734 4200 4990
C
203 229 229 254 254 305 356 406 457 508 508 610 610 686 762 762 762 762 -
Fl.
21 32 35 53 75 87 139 210 302 410 520 690 900
B/W
19 27 27 43 64 77 118 198 271 365 490 665 865
B/W
216 241 283 305 381 403 419 457 501 762 838 914 991 1143 1397 -
B
399 505 505 604 830 830 1039 1265 1460 1590 1791 2126 2261 2654 4267 -
C
203 229 229 254 356 356 406 457 508 508 610 686 686 762 1016 -
Fl.
25 48 53 78 135 158 234 355 495 750 958
B/W
23 34 41 55 105 111 186 284 400 620 850
B
399 541 635 874 1044 1239 1476 1565 2062 2062 3048 3150 -
C
203 254 305 457 457 508 610 610 762 762 762 762 -
Fl.
42 67 119 252 418 652 1100
B/W
36
178 191 203 229 254 267 292 330 356 381 406 432 457 508 610 610 711 711 813 864
1600 1465 1955 1760 2075 1840 2150 1960 3620 3180 -
1410 1375 2060 1750 3100 2850 3350 2950 * 3000 * 4500 * 6000
10
Description
Body Body Seat Ring Wedge Stem Gasket RTJ Bonnet Stud Stud Nut Back-seat Bush Packing Gland Gland Flange Eye Bolt Eye Bolt Nut Yoke Sleeve (Stem Nut) Bearing Yoke Cap Screw Handwheel Handwheel Nut Nameplate
Material
ASTM A216 Gr. WCB ASTM A105 + HF* ASTM A216 Gr. WCB + 13% Cr. Steel ASTM A182 Gr. F6a Soft Iron ASTM A216 Gr. WCB ASTM A193 Gr. B7 ASTM A194 Gr. 2H 13% Cr. Steel Graphite with braided end rings 13% Cr. Steel ASTM A105 / ASTM A216 Gr. WCB 13% Cr. Steel ASTM A194 Gr. 2H ASTM A439 Type D2 Steel Ductile Iron Steel Steel / Ductile Iron / Malleable Iron SS 304
FLANGED END
* HF - Hard-Faced with Stellite #6 or equivalent For other body / bonnet materials, refer page 5
BUTT-WELD END
A Fl.
368 470 546 705 832 991 1130
B B/W
368 470 546 705 832 991 1130 570 720 850 1200 1600 1950 2150
C
229 305 356 508 508 762 762
Approx.Wt. Fl.
128 255 315 643
B/W
126 196 375 625
B/W
115 245 285 570
11
Description
Body Body Seat Ring Disc Disc Washer Stem Disc Stem Nut Gasket Bonnet Stud Stud Nut Back-seat Bush Packing Gland Gland Flange Eye Bolt Eye Bolt Nut Groove Pin Yoke Bush Handwheel Washer Handwheel Nut Nameplate
Material
ASTM A216 Gr. WCB ASTM A182 Gr. F6a+HF ASTM A216 Gr. WCB + 13% Cr. Steel 13% Cr. Steel ASTM A182 Gr. F6a 13% Cr. Steel ASTM A308 ASTM A216 Gr. WCB ASTM A193 Gr. B7 ASTM A194 Gr. 2H 13% Cr. Steel Graphite with braided end rings 13% Cr. Steel ASTM A105 / ASTM A216 Gr. WCB Cr. - Mo Steel ASTM A194 Gr. 2H Steel ASTM A439 Type D2 Steel / Ductile Iron / Malleable Iron Steel ASTM A563 Gr. B SS 304
* HF - Hard-Faced with Stellite #6 or equivalent For other body / bonnet materials, refer page 5
BUTT-WELD END
Approx.Wt. B/W
292 356 432 559 661 787 838
Fl.
203 216 242 292 406 495 623 699
B
335 355 421 477 552 635 895 1215
C
203 203 254 254 356 457 356 610
Fl.
23 35 41 66 118 207 335 495
B/W
20 38 62 110 195 320 470
B/W
267 317 356 444 559 623 711
B
355 410 457 556 668 830 1020 1160
C
203 203 254 356 457 610 610 762
Fl.
33 46 58 97 186 329 520 705
B/W
28 50 84 164 296 471 634
B
400 533 660 817 947 1285 1560
C
254 356 406 610 610 762 762
Fl.
42 75 136 245 546 756 1086
B/W
38 60 116 195 466 656 896
12
Description
Body Body Seat Disc Disc Washer Stem Disc Stem Nut Gasket RTJ Bonnet Stud Stud Nut Back-seat Bush Spacer Packing Eye Bolt Eye Bolt Nut Gland Handwheel Handwheel Nut Retainer Nut Yoke Sleeve Bearing Nameplate
Material
ASTM A216 Gr. WCB Integral Stellite #6 or eq. ASTM A216 Gr. WCB + 13% Cr. Steel 13% Cr. Steel ASTM A182 Gr. F6a 13% Cr. Steel SS 316 ASTM A216 Gr. WCB ASTM A193 Gr. B7 ASTM A194 Gr. 2H 13% Cr. Steel 13% Cr. Steel Graphite with braided end rings ASTM A193 Gr. B7 ASTM A194 Gr. 2H 13% Cr. Steel Steel / Ductile Iron / Malleable Iron ASTM A439 Type D2 Steel SS 304
* HF - Hard-Faced with Stellite #6 or equivalent For other body / bonnet materials, refer page 5
FLANGED END
A Fl.
368 470 546 -
B B/W
368 470 546 590 720 850 -
C
305 305 356 -
Approx.Wt. Fl.
110 255 315 -
Fl.
B/W
120 180 395
B/W
85 195 265 -
13
Description
Body Body Seat Ring Disc Hinge Disc Washer Disc Nut Disc Nut Pin Hinge Pin Gasket Cover Stud Stud Nut Hinge Pin Cover Hinge Pin Cover Bolt Nameplate
Material
ASTM A216 Gr. WCB ASTM A105 + HF* ASTM A216 Gr. WCB + 13% Cr. Steel ASTM A216 Gr. WCB 13% Cr. Steel SS 304 13% Cr. Steel 13% Cr. Steel ASTM A308 ASTM A216 Gr. WCB ASTM A193 Gr. B7 ASTM A194 Gr. 2H ASTM A105 ASTM A193 Gr. B7 SS 304
FLANGED END
* HF - Hard-Faced with Stellite #6 or equivalent For other body / cover materials, refer page 5
BUTT-WELD END
COVER & EYEBOLT ARRANGEMENT FOR VALVES 14 & ABOVE (CLASS 150), VALVES 10 & ABOVE (CLASS 300) & VALVES 4 & ABOVE (CLASS 600)
Fl.
203 216 241 292 356 495 622 698 788 864 978 978 1295
t
B
Approx.Wt. B/W
292 356 432 559 661 787 838 -
Fl.
21 24 34 49 88 168 280 413 509 580 635 925
B/W
19 20 30 42 79 154 260 382 466 524 583 855
B/W
267 317 356 444 533 622 711 839 864 978 1016 1346
B
165 190 229 279 343 368 412 559 636 562 675 790
Fl.
24 45 70 151 242 333 450 659 873 1090
B/W
19 36 56 129 210 284 378 556 747 900
B
178 203 229 365 442 450 590 -
Fl.
35 55 92 204 323 550 790 -
B/W
30 46 70 161 260 455 680 -
165 175 181 213 273 335 406 483 515 455 500 675 780
1500 1403
14
Description
Body Body Seat Ring Disc Hinge Hinge Pin Disc Washer Disc Nut Disc Nut Pin Gasket RTJ Cover Stud Stud Nut Nameplate
Material
ASTM A216 Gr. WCB + HF* ASTM A105N + HF* ASTM A216 Gr. WCB + 13% Cr. Steel ASTM A216 Gr. WCB 13% Cr. Steel 13% Cr. Steel SS 304 SS 304 Soft Iron ASTM A216 Gr. WCB ASTM A193 Gr. B7 ASTM A194 Gr. 2H SS 304
* HF - Hard-Faced with Stellite #6 or equivalent For other body / cover materials, refer page 5
BUTT-WELD END
A Fl.
368 470 546 705 832 991 1130
B B/W
368 470 546 705 832 991 1130 250 285 340 400 465 570 680
Approx.Wt. Fl.
69 118 177 566 892
Fl.
B/W
70 131 275 569 789 1280
B/W
53 89 134 467 728
15
Body and Bonnet The body and bonnet are cast with uniform section and generous radius fillets to prevent stress concentration. The castings are precision-machined for high performance.
Flexible Wedge The valves feature a one-piece cast flexible wedge that minimises stress concentration. Wedge flexibility ensures tight seating over a wide range
The gate valve body has a straight through port without recesses except at the seat area. This ensures minimum turbulence, erosion and resistance to flow. Long integral guide ribs in the body match with full-length guide slots in the wedge fo accurate alignment and guidance.
of
differential
pressures
and
temperatures. It also adjusts to slight misalignments caused by pipeline deflections and thermal deformation. The stem-to-wedge thrust is applied close to the wedge centre. This reduces lateral stem loading and provides for more accurate wedge movement.
Ordering Information
Valve Size mm (in)
50 (2) 80 (3) 100 (4) 150 (6) 200 (8) 250 (10) 300 (12)
GO for Gear Operation LA for Locking Arrangement E for Electrical Actuator As a standard, API 603 Gate Valves are made of Stainless Steel ASTM A351 Grade CF8M. For accesories like gear operation and electrical actuators, suffix suitable abbreviations to the above ordering code such as :
Valve Type
End Connection
3 Flanged RF 10 12 16
Trim
16
Description
Body Wedge Stem Gasket - Cl.150 Gasket - Cl.300 Bonnet Stud Stud Nut Spacer Packing Eye Bolt Eye Bolt Nut Gland Gland Flange Yoke Sleeve (Stem Nut) Grease Fitting Retainer Nut Handwheel Handwheel Nut Nameplate
Material
ASTM A351 Gr. CF8M ASTM A351 Gr. CF8M ASTM A182 Gr. F316 Graphite with SS 316 insert Spirally-wound SS 304 with graphite filler ASTM A351 Gr. CF8M ASTM A193 Gr. B8 Cl.2 ASTM A194 Gr. 8 SS 316 Graphite with braided end rings SS 316 ASTM A194 Gr. 8 SS 316 SS 316 ASTM A439 Type D2 SS 304 SS 304 ASTM A536 Gr. 60-40-18 / ASTM A602 Gr. M3210 SS 304 SS 304
Class 150 A
178 203 229 267 292 330 356
B
385 495 610 820 1025 1250 1655
C
160 204 229 254 305 356 406
A
216 283 305 403 419 457 502
B
400 505 630 860 1060 1280 1780
C
204 229 254 356 406 457 508
Approx.Wt.
24 45 67 121 184 295 416
17
GATE VALVES
Parallel Slide Disc Mechanism This mechanism consists of two independent discs held by a disc carrier. An alloy steel spring between the discs provides the initial loading to keep the discs pressed against the body seats. The disc faces are parallel to each other and seal on parallel seat rings in the body. Sealing takes place by utilizing the line pressure to provide tight seal on the downstream seat. As the two discs are independent and parallel, opening / closing torques are significantly lower than comparable wedge disc designs, thereby minimizing the possibility of jamming at high temperatures or pressures. When the valve is operated, the discs are allowed to slide and rotate over the body seats. This helps wipe out foreign particles from the seat faces. Yoke Sleeve and Thrust Bearings The yoke sleeve is made of nodular Niresist Iron, supported by a set of bearings to reduce friction and the consequent torque required to operate the valves. Nodular Niresist Iron also withstands high temperatures. Weather seals, provided in the yoke sleeve, protect the bearing area against ingress of dirt and water.
disc carrier
Pressure Seal arrangement for body-bonnet joint This pressure seal body-bonnet joint utilizes the line pressure to create a tight body-bonnet seal. Sealing is achieved by compressing a high-purity graphite gasket between the bonnet and the body retainer ring. Preloaded fasteners provide an initial tight seal at low line pressures. At higher pressures, the line pressure pushes up the bonnet against the gasket, compressing it further and providing a much tighter seal.
bonnet high-purity graphite gasket
Seat Rings Body seat rings are welded to the body to offer a leakproof design as they eliminate the leakage path betwen the seat ring and the body. This design is superior to screwed seats which can loosen up due to temperature fluctuations, corrosion or vibration and result in leakage.
Trim Both the disc and the seat ring faces are hard-faced with Stellite #6 or equivalent.
Stem and Gland Packing The valves feature a stem, made of 13% Cr. Steel - ACME threaded, precision-machined and ground to a high finish to ensure a smooth operation. The high-purity graphite gland packings, used for stem sealing, provide capability to withstand high temperatures and pressures, and also to resist many chemicals. The smooth-finish stuffing box ensures longer life for the packings.
Accessories AIL Valves can be supplied with accessories such as bypass arrangement, drain plugs, live-loading and mountings like extension spindles, floor stands and chain wheel. The valves can also be supplied with gear units and electrical actuators.
18
Y-GLOBE VALVES
By virtue of their Y-type configuration, AIL Y-Globe Valves have a relatively straight flow and a lower pressure drop compared to conventional globe valves. The valves are suitable for tight shutoff and throttling in high pressure and high temperature lines. Some of the unique features of AIL Y-Globe Valves are :
l l l l l l
Pressure Seal Bonnet Low operating torque due to use of thrust bearings Non-rotating stem Integrally-stellited body seats Fully-guided disc with Stellite seating and guiding surface Impactor handwheel in sizes of 6 (150mm) and above
Ordering Information
Valve Size mm (in)
50 (2) 80 (3) 100 (4) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) 450 (18) 500 (20) 600 (24)
Valve Type
End Connection
/2 Butt-weld
Trim
Disc
U Hard-faced
19
Pr. Seal Bonnet Gate Valves - ASME Class 900, 1500 & 2500
Figure Numbers 3811/2UP, 3861/2UP & 3911/2UP
Standard Material of Construction
Sl. No.
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
Description
Body Body Seat Ring Disc Bonnet Stem Yoke Yoke Sleeve Packing Spring Gasket Stud Stud Nut Gland Stud Gland Nut Thrust Ball Bearing Handwheel Nameplate ASTM A216 Gr. WCB
Material
ASTM A217 Gr. WC6 ASTM A217 Gr. WC9
ASTM A216 ASTM A217 ASTM A217 Gr. WCB+HF* Gr. WC6+HF* Gr. WC9+HF* ASTM A216 ASTM A217 ASTM A217 Gr. WCB+HF* Gr. WC6+HF* Gr. WC9+HF* ASTM A216 Gr. WCB ASTM A217 Gr. WC6 ASTM A217 Gr. WC9
13% Cr. Steel ASTM A216 Gr. WCB ASTM A439 Type D2 Graphite with braided end rings Inconel X750 / Nimonic 90 Graphite ASTM A193 Gr. B7 ASTM A194 Gr. 2H ASTM A193 Gr. B7 ASTM A194 Gr. 2H Steel Steel / Malleable Iron / SG Iron SS 304
Class 900 B
470 580 730 890 1040 1540 1785 1825 2050 * * *
Size
50 (2) 80 (3) 100 (4) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) 450 (18) 500 (20) 600 (24)
C
229 305 356 508 686 762 762 762 762 * * *
A
216 305 406 559 711 864 991 1067 1194 1346 1473
B
470 580 730 890 1375 1540 1720 1730 2100 2150 2500
C
229 305 356 508 508 762 762 762 762 762 762
A
279 368 457 610 762 914 1041 1118 1245 1397 *
B
450 710 720 925 1370 1490 1690 1850 2050 2300 *
C
229 457 457 610 762 762 762 762 762 762 *
Approx.Wt.
50 120 140 305 685 1270 1895 * * * *
* Refer to AIL 2 valves are in flexible wedge design. Valves in sizes of 10 and above in Class 900 and, 8 and above in Classes 1500 and 2500 are supplied with gear unit.
20
Description
Body Bonnet Disc Stem Packing Yoke Gasket Stud Stud Nut Nameplate
Material
ASTM A216 ASTM A217 ASTM A217 Gr. WCB+HF* Gr. WC6+HF* Gr. WC9+HF* ASTM A216 ASTM A217 ASTM A217 Gr. WCB Gr. WC6 Gr. WC9 SS 410 Hard-Faced with Stellite #6 or equiv. ASTM A479 Type 410 Graphite with braided end rings ASTM A216 Gr. WCB Graphite ASTM A193 Gr. B7 ASTM A194 Gr. 2H SS 304
B - OPEN (Max.)
Class 1500 A
470 546 705 832
B
650 875 1210 2000
C
508 508 762 762
Approx.Wt.
? ? ? ?
A
Pr. Seal Cover Swing Check Valves - ASME Class 900, 1500 & 2500
Figure Nos. 3801/2U, 3851/2U & 3901/2U
Standard Material of Construction
Sl. No.
01 02 03 04 05 06 07 08
Description
Body Cover Disc Seat Ring Hinge Pin Gasket Stud Stud Nut Nameplate
Material
ASTM A216 ASTM A217 ASTM A217 Gr. WCB Gr. WC6 Gr. WC9 ASTM A216 ASTM A217 ASTM A217 Gr. WCB+HF* Gr. WC6+HF* Gr. WC9+HF* 13% Cr. Steel Graphite ASTM A193 Gr. B7 ASTM A194 Gr. 2H SS 304
Class 1500 A
216 305 406 559 711 864 991 1067 1194
Class 2500 A
279 368 457 610 762 914 1041 * *
A
991 -
B
630 -
Approx.Wt.
780 -
B
240 275 275 310 415 500 605 630 750
Approx.Wt.
35 45 62 110 250 435 600 875 *
B
240 240 300 360 485 615 665 * *
Approx.Wt.
40 55 80 180 320 945 1135 * *
21
Extended Bonnet Optional extended bonnet with vapour column length according to BS 6364 and / or customer specifications is furnished. The vapour column allows the stem packing to be functional by keeping it away from the cryogenic fluid. Testing and Standards AIL Cryogenic Valves are type-tested as per valve standards and specifications of leading oil companies as part of the design verification process.
Description
Body Body Seat Ring Wedge Stem Gasket Bonnet Stud Stud Nut Back Seat Packing Gland Yoke Sleeve Grease Fitting Retainer Nut Handwheel Handwheel Nut Nameplate
Materials of construction are selected, based on the service fluid, temperature and customer specifications.
For dimensions of A and C, refer page 10 for corresponding tables under API 600 range of valves. Dimension B will be as per customer requirement.
Description
Body Body Seat Ring Disc Disc washer Stem Disc Stem Nut Gasket Bonnet Stud Stud Nut Back Seat Packing Gland Handwheel Handwheel Yoke Bush Nameplate
For dimensions of A and C, refer page 12 for corresponding tables under API 600 range of valves. Dimension B will be as per customer requirement.
Materials of construction are selected, based on the service fluid, temperature and customer specifications.
23
Soft-seated Valves
In applications that require positive shutoff such as in chemical and petrochemical services, the AIL Soft-seated Gate Valve is a suitable solution. PTFE seat inserts provide the necessary soft-seating to ensure positive shutoff.
PTFE seat inserts for positive shutoff Block-and-Bleed capability Dual seating (metallic and soft seats) Intrinsically fire-safe Bubble-tight performance
All API 600 AIL gate valves can be offered with the option of soft-seating for sizes up to 10 (250mm).
Through conduit, full-bore (piggable) or reduced-bore Valve seat with PTFE inserts for bubble-tight seal Self-relieving seat ring Different options available for stem packing system
l l l
Gland Packing of high-purity, flexible graphite, sandwiched between braided graphite end-rings with Inconel wire mesh reinforcement. On request, gland packing with conical / wedgeshaped configuration can also be offered. Bonnet gasket in valves of ASME Class 150 is made of graphiteSS 316 insert. Valves of Class 300 feature gaskets of spirallywound stainless steel with graphite filler. In valves of Class 600 and higher, metallic ring gaskets are offered. The stem finish is 16-32 RMS, with a straightness of 0.001 0.005 over the length of the plain shank. Cylindricity is controlled as per AIL standards. The Stuffing Box surface finish is 180 RMS max., and its straightness is controlled as per AIL standards. The diametrical clearances between the stem, gland and the stuffing box are controlled to close tolerances, to ensure that emission norms are complied with.
24
CHAIN WHEELS
Chain wheels are used for the valves located too far above the floor for convenient hand wheel operation. Chain wheels are available for all types of AIL Cast Steel Valves and can be substituted in place or used along with the existing hand wheel. AIL chain wheels are equipped with guards or guides, not only to keep the chain from slipping off from the wheel but also to hold the chain in close contact with a large portion of the circumference of the hand wheel or the gear wheel.
Valve Type
ASME Class
150 300 600 900 1500 2500 150 300 600 900 1500
API 600
Standard
24 & above 20 & above 16 & above 8 & above 6 & above 10 & above 10 & above 6 & above -
ASME B16.34
Standard
10 & above 10 & above 8 & above -
Optional
14 - 20 14 - 18 8 -14 -
Optional
6 & 8 6 & 8 6 -
Globe
Gate
LANTERN RING
As mentioned earlier in page 7, a lantern ring is used to provide further integrity to the gland packing area in gate and globe valves, to prevent escape of service fluid to the atmosphere. This finds application in stringent environment conditions or in the case of potentially harmful service fluids. The lantern ring is provided between two sets of packing rings, with a leakoff plug that gives the option of removal of leakage, if any, from the lower packing rings. Alternatively, a sealing fluid can be introduced through the plug to prevent incidental leakage through the lower packing rings. Lantern rings serve a useful purpose. But, since they are a possible source of shaft scoring, it is advisable to restrict their usage to essential applications.
ELECTRICAL ACTUATORS
Electrical Actuators may be used with AIL valves in all sizes and class ratings. The actuators can be operated in practically any position or location, and have a provision for manual operation. The actuators come in weatherproof enclosure as a standard, and in explosion-proof and such other special enclosures too. For correct selection of actuator, please specify details of line pressure, differential pressure when closed, power supply requirements and actuator accessories.
BYPASS ARRANGEMENT
A bypass arrangement serves two purposes - first, in steam services, to warm up the line before opening of the main valve, and secondly, in steam and other lines, to balance the pressure on both sides of the main valve wedge or disc to bring down the valve opening torque. As an option, almost all AIL valves can be furnished with bypass arrangement. The bypassconsists of a single Outside Screw & Yoke globe valve with a pressure / temperature rating and corrosion resistance equal to or exceeding that of the main valve.
POSITION INDICATORS
Valves can be provided with position indicators as a visible means to indicate the open and closed positions. Typically, for gate valves, the indicator is in the form of a pointer travelling along a fixed scale.
Size Chart
Main valve Bypass valve 2to 4 1 /2 5to 8 3 /4 10 or higher 1
LOCKING DEVICES
Bypass valve is attached to the side of the main valve with the stems of the both valves parallel and pointing upward. Where service conditions warrant larger-than-standard bypasses, it is recommended that the installation of the bypasses be around the main valve. Locking devices are used to secure a handwheel in a fixed position, to prevent accidental or unauthorized operation of a valve. The locking arrangement typically allows the use of chain and padlock to secure the valve.
25
Technical Information
#300
740 675 655 635 600 550 535 535 505 410 270 170 105 50 -
#600
1480 1350 1315 1270 1200 1095 1075 1065 1010 825 535 345 205 105 -
900
2220 2025 1970 1900 1795 1640 1610 1600 1510 1235 805 515 310 155 -
#1500
3705 3375 3280 3170 2995 2735 2685 2665 2520 2060 1340 880 515 260 -
#2500
6170 5625 5470 5280 4990 4560 4475 4440 4200 3430 2230 1430 860 430 -
#300
750 750 720 695 665 605 590 570 530 510 485 450 320 215 145 95 60 40
#600
1500 1500 1445 1385 1330 1210 1175 1135 1065 1015 975 900 640 430 290 190 125 75
#900
2250 2250 2165 2080 1995 1815 1765 1705 1595 1525 1460 1350 955 650 430 290 185 115
#1500
3750 3750 3610 3465 3325 3025 2940 2840 2660 2540 2435 2245 1595 1080 720 480 310 190
#2500
6250 6250 6015 5775 5540 5040 4905 4730 4430 4230 4060 3745 2655 1800 1200 800 515 315
#300
750 750 730 705 665 605 590 570 530 510 485 450 375 260 175 110 70 40
#600
1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 900 755 520 350 220 135 80
900
2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1350 1130 780 525 330 205 125
#1500
3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 2245 1885 1305 875 550 345 205
#150
290 260 230 200 170 140 125 110 95 80 65 50 35 20 *20 *20 *20 *20
#300
750 745 715 705 665 605 590 570 530 510 485 370 275 200 145 100 60 35
#600
1500 1490 1430 1410 1330 1210 1175 1135 1055 1015 965 740 550 400 290 200 125 70
#900
2250 2235 2150 2115 1995 1815 1765 1705 1585 1525 1450 1110 825 595 430 300 185 105
#1500
3750 3725 3580 3530 3325 3025 2940 2840 2640 2540 2415 1850 1370 995 720 495 310 170
#2500
6250 6205 5965 5880 5540 5040 4905 4730 4400 4230 4030 3085 2285 1665 1200 830 515 285
#300
695 655 640 620 585 535 525 520 475 390 270 170 105 50
#600
1390 1315 1275 1235 1165 1065 1045 1035 945 780 535 345 205 105
900
2085 1970 1915 1850 1745 1600 1570 1555 1420 1175 805 515 310 155
#1500
3470 3280 3190 3085 2910 2665 2615 2590 2365 1955 1340 860 515 260
#150
290 260 230 200 170 140 125 110 95 80 65 50 35 20
#300
750 750 730 705 665 605 590 570 505 410 270 170 105 50
#600
1500 1500 1455 1410 1330 1210 1175 1135 1010 825 535 345 205 105
#900
2250 2250 2185 2115 1995 1815 1765 1705 1510 1235 805 515 310 155
#1500
3750 3750 3640 3530 3325 3025 2940 2840 2520 2060 1340 860 515 260
#2500
6250 6250 6070 5880 5540 5040 4905 4730 4200 3430 2230 1430 860 430
#300
720 600 540 495 465 435 430 425 415 405 395 390 380 320 255 200 155 115 85 60 50 35 25
#600
1440 1200 1080 995 930 875 860 850 830 805 790 780 765 640 615 515 400 310 225 170 125 95 70 55
900
2160 1800 1620 1490 1395 1310 1290 1275 1245 1210 1190 1165 1145 965 925 770 595 465 340 255 185 145 105 80
#1500
3600 3000 2700 2485 2330 2185 2150 2125 2075 2015 1980 1945 1910 1605 1545 1285 995 770 565 430 310 240 170 135
#150
275 235 215 195 170 140 125 110 95 80 65 50 35 20 *20 *20 *20 *20 *20 *20 *20 *20 *20 *20
#300
720 620 560 515 480 450 445 430 425 420 420 415 385 350 345 305 235 185 145 115 95 75 60 40
#600
1440 1240 1120 1025 955 900 890 870 855 845 835 830 775 700 685 610 475 370 295 235 190 150 115 85
#900
2160 1860 1680 1540 1435 1355 1330 1305 1280 1265 1255 1245 1160 1050 1030 915 710 555 440 350 290 225 175 125
#1500
3600 3095 2795 2570 2390 2255 2220 2170 2135 2110 2090 2075 1930 1750 1720 1525 1185 925 735 585 480 380 290 205
#2500
6000 5160 4660 4280 3980 3760 3700 3620 3560 3520 3480 3460 3220 2915 2865 2545 1970 1545 1230 970 800 630 485 345
26
* For weld-end valves only. Flanged-end ratings terminate at 10000F. ** Not recommended for prolonged use above 8000F (4250C).
Technical Information
#300
750 750 730 705 665 605 590 570 530 510 485 450 375 255 170 115 75 50
#600
1500 1500 1455 1410 1330 1210 1175 1135 1065 1015 975 900 755 505 345 225 150 105
900
2250 2250 2185 2115 1995 1815 1765 1705 1595 1525 1460 1350 1130 760 515 340 225 155
#1500
3750 3750 3640 3530 3325 3025 2940 2840 2660 2540 2435 2245 1885 1270 855 565 375 255
#2500
6250 6250 6070 5880 5540 5040 4905 4730 4430 4230 4060 3745 3145 2115 1430 945 630 430
#300
750 750 750 750 750 715 700 695 630 515 335 215 130 65 -
#600
1500 1500 1500 1500 1500 1425 1400 1390 1260 1030 670 430 260 130 -
900
2250 2250 2250 2250 2250 2140 2100 2080 1890 1545 1005 645 385 195 -
#1500
3750 3750 3750 3750 3750 3565 3495 3470 3150 2570 1670 1070 645 320 -
#150
290 290 290 290 290 290 290 280 280 275 260 225 155 105 70 45 30 20
#300
750 750 750 750 750 750 750 735 730 720 680 585 400 270 180 120 75 45
#600
1500 1500 1500 1500 1500 1500 1500 1465 1460 1440 1355 1175 795 540 360 240 155 95
#900
2250 2250 2250 2250 2250 2250 2250 2200 2185 2160 2030 1760 1195 810 540 360 230 140
#1500
3750 3750 3750 3750 3750 3750 3750 3665 3645 3600 3385 2935 1995 1350 900 600 385 235
#2500
6250 6250 6250 6250 6250 6250 6250 6110 6070 6000 5645 4895 3320 2250 1500 1000 645 395
#300
750 750 740 725 720 720 715 710 690 675 645 600 470 325 220 135 85 50
#600
1500 1500 1485 1450 1440 1440 1430 1425 1380 1345 1285 1200 945 650 435 275 170 105
900
2250 2250 2225 2175 2160 2160 2145 2135 2070 2020 1930 1800 1415 975 655 410 255 155
#1500
3750 3750 3705 3620 3600 3600 3580 3555 3450 3365 3215 3000 2355 1630 1095 685 430 255
#150
265 265 265 265 265 265 260 255 190 130 85 50 25 -
#300
695 695 695 695 695 695 680 665 490 335 215 130 65 -
#600
1390 1390 1390 1390 1390 1390 1360 1185 980 670 430 260 130 -
#900
2085 2085 2085 2085 2085 2085 2040 1775 1465 1005 645 385 195 -
#1500
3470 3470 3470 3470 3470 3470 3400 2960 2445 1670 1070 645 320 -
#2500
5785 5785 5785 5785 5785 5780 5670 4930 4070 2785 1785 1070 535 -
* For weld-end valves only. Flanged-end ratings terminate at 10000F. @ Not to be used over 6500F.
* For weld-end valves only. Flanged-end ratings terminate at 10000F. ** Not recommended for prolonged use above 8000F (4250C).
27
Technical Information
ASME Class 300 Raised Face (in mm) Bolt No. Dia
/8 5 /8 5 /8 5 /8 3 /4 3 /4 3 /4 7 /8 7 /8 1 1 11/8 11/8 11/4
5
A
152 178 190 229 254 279 343 406 483 533 597 635 698 813
B
120 139 152 190 216 241 298 362 432 476 539 578 635 749
C
92 105 127 157 186 216 270 324 381 413 470 533 584 692
D
19.1 (15.9) 22.3 (17.5) 23.9 (19.1) 23.9 23.9 25.4 28.6 30.2 31.8 35.0 36.6 39.7 42.9 47.7
E
19 19 19 19 22 22 22 25 25 29 29 32 32 35 4 4 4 8 8 8 8 12 12 12 16 16 20 20
A
165 190 210 254 279 318 381 444 521 584 648 711 775 914
B
127 149 168 200 235 270 330 387 451 514 571 628 686 813
C
92 105 127 157 186 216 270 324 381 413 470 533 584 692
D
22.3 25.4 28.6 31.8 35.0 36.6 41.3 47.7 50.8 54.0 57.2 60.4 63.5 69.9
E
19 22 22 22 22 22 25 29 32 32 35 35 35 41 8 8 8 8 8 12 12 16 16 20 20 24 24 24
Large-size End Flange Dimensions as per ASME 16.47, 1996 Series A (MSS SP 44)
ASME Class
Large-size End Flange Dimensions as per ASME 16.47, 1996 Series B (API 605)
Bolt No.
28 28 32 32 36 44 28
ASME Class
D
71 75 83 90 97 108 95
E
35 35 41 41 41 41 48
Dia
13/8 13/8 11/2 11/2 11/2 11/2 13/4
D
48 51 57 59 68 75 94
E
22 22 25 25 28 28 41
Bolt No.
40 44 40 44 48 44 36
Dia
/4 /4 /8 7 /8 1 11/8 13/8
3 7 3
700 (28) 927 864 800 750 (30) 984 914 857 850 (34) 1111 1029 965 CL. 150 900 (36) 1168 1086 1022 1050 (42) 1346 1257 1194 1200 (48) 1511 1422 1359 1092 997 857 CL. 300 750 (30) Height of raised face is 1.6mm (0.06) each.
700 (28) 837 795 762 750 (30) 887 846 813 850 (34) 1005 957 921 CL. 150 900 (36) 1057 1010 972 1050 (42) 1226 1171 1130 1200 (48) 1392 1335 1289 991 921 845 CL. 300 750 (30) Height of raised face is 1.6mm (0.06) each.
ASME Class 600 Ring Type (in mm) Bolt No. Dia
/8 /4 /4 7 /8 1 1 11/8 11/4 11/4 13/8 11/2 15/8 15/8 17/8
3 3 5
E
19 22 22 25 29 29 32 35 35 38 41 45 45 51 8 8 8 8 8 12 12 16 20 20 20 20 24 24
Pitch -P
83 100 124 150 181 211 270 324 381 419 470 533 584 692
Depth E
8.0 8.0 8.0 8.4 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 9.5 11.1
Width F
12.0 12.0 12.0 8.7 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 13.5 16.6
Bottom Rad. R
0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76 1.52 1.52
50 (2) 165 127 92 65 (21/2) 190 149 105 80 (3) 210 168 127 100 (4) 273 216 157 125 (5) 330 266 186 150 (6) 356 292 216 200 (8) 419 349 270 250 (10) 508 432 324 300 (12) 559 489 381 350 (14) 603 527 413 400 (16) 686 603 470 450 (18) 743 654 533 500 (20) 813 724 584 600 (24) 940 838 692 Height of raised face is 1.6mm (0.06) each.
50 (2) 165 127 108 25.4 R23 65 (21/2) 190 149 127 28.6 R26 80 (3) 210 168 146 31.8 R31 100 (4) 273 216 171 38.1 R37 125 (5) 330 266 209 44.5 R41 150 (6) 356 292 241 47.7 R45 200 (8) 419 349 302 55.6 R49 250 (10) 508 432 356 63.5 R53 300 (12) 559 489 413 66.7 R57 350 (14) 603 527 457 69.9 R61 400(16) 686 603 508 76.2 R65 450 (18) 743 654 575 82.6 R69 500 (20) 813 724 635 88.9 R73 600 (24) 940 838 749 101.6 R77 Height of raised face is 1.6mm (0.06) each. Grv. - Groove
ASME Class 900 Ring Type (in mm) Bolt No. Dia
/8 1 /8 11/8 11/4 11/8 13/8 13/8 13/8
7 7
Valve Size A
216 244 241 292 349 381 470 546 610
A
216 244 241 292 349 381 470 546 610
B
165 191 191 235 279 318 394 470 533
C
92 105 127 157 186 216 270 324 381
D
38.1 41.1 38.1 44.5 50.8 55.6 63.5 69.9 79.2
E
25.4 28.4 25.4 31.8 35.1 31.8 38.1 38.1 38.1 8 8 8 8 8 12 12 16 20
B
185 191 191 235 279 318 394 470 533
C
124 137 146 171 209 241 308 362 419
D
38.1 41.1 38.1 44.5 50.8 55.8 63.5 69.9 79.2
Grv. No.
R24 R27 R31 R37 R41 R45 R49 R53 R57
Pitch -P
95 108 124 149 181 211 270 324 381
Depth E
8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0
Width F
12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0
Bottom Rad. R
0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76
50 (2) 65 (21/2) 80 (3) 100 (4) 125 (5) 150 (6) 200 (8) 250 (10) 300 (12)
ASME Class 1500 Ring Type (in mm) Bolt No. Dia
/8 1 11/8 11/4 11/2 13/8 15/8 17/8 2
7
Valve Size
50 (2) 65 (21/2) 80 (3) 100 (4) 125 (5) 150 (6) 200 (8) 250 (10) 300 (12)
A
216 244 267 311 375 394 483 584 673
B
165 191 203 241 292 318 394 483 572
C
92 105 127 157 186 216 270 324 381
D
38.1 41.1 47.8 53.8 73.2 82.6 91.9 108.0 124.0
E
25.4 28.4 31.8 35.1 41.1 38.1 44.5 50.8 53.8 8 8 8 8 8 12 12 12 16
A
216 244 241 292 349 381 470 546 610
B
185 191 191 235 279 318 394 470 533
C
124 137 146 171 209 241 308 362 419
D
38.1 41.1 38.1 44.5 50.8 55.8 63.5 69.9 79.2
Grv. No.
R24 R27 R31 R37 R41 R45 R49 R53 R57
Pitch -P
95 108 124 149 181 211 270 324 381
Depth E
8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0
Width F
12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0
Bottom Rad. R
0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.76
28
Technical Information
Note : Internal surface may be reformed or machined for dimensions B at root face. Contour within the envelope is manufacturers option, unless otherwise specifically ordered for.
Nominal Pipe Size
65 (21/2) 80 (3) 100 (4) 125 (5) 150 (6) 200 (8) 250 (10) 300 (12) 350 (14) 400 (16) 450 (18) 500 (20) 600 (24)
A
75 91 117 144 172 223 278 329 362 413 464 516 619
B STD
305 337 387 438 489 591
XS
298 330 432 483 584
30
581
40
63 78 102 128 154 203 255 303 333 381 429 478 575
60
198 247 295 325 373 419 467 560
80
59 74 97 122 148 194 242 289 318 364 410 456 548
100
189 237 281 308 354 398 443 532
120
92 116 140 183 230 273 300 344 387 432 518
140
178 222 267 292 333 378 419 505
160
54 67 87 110 132 173 216 257 284 325 367 408 491
XXS
45 58 80 103 124 175 -
Carbon Steel
A216 Gr. WCB A352 Gr. LCC A217 Gr. WC6
Alloy Steel
A217 Gr. WC9 A217 Gr. C5
Stainless Steel
A351 Gr. CF8 A351 Gr. CF8M
$0.30 1.00 0.04 0.045 0.60 *0.30 *0.50 *0.50 *0.20 *0.30 -
0.25 1.20 0.04 0.045 0.60 0.30 *0.50 *0.50 *0.20 *0.30 -
0.05 - 0.20 0.50 - 0.80 0.04 0.045 0.60 *0.30 *0.50 1.00 - 1.50 0.45 - 0.65 *0.30 *0.10
0.05 - 0.18 0.50 - 0.70 0.04 0.045 0.60 *0.50 *0.50 2.00 - 2.75 0.90 - 1.20 *0.30
$
0.20 0.40 - 0.70 0.04 0.05 0.75 *0.50 *0.50 0.45 - 0.65 *0.10
* Total content of thee residual materials shall not exceed1%. AIL material standard is 0.25 max. Values indicated are all maximum, except when a range is specified.
0.37 - 0.49 0.65 - 1.10 0.35 0.04 0.15 - 0.35 0.75 - 1.20 0.15 - 0.25 -
0.38 - 0.48 0.75 - 1.00 0.035 0.04 0.15 - 0.35 0.80 - 1.10 0.15 - 0.25 -
0.37 - 0.49 0.65 - 1.10 0.04 0.04 0.15 - 0.35 0.75 - 1.20 0.15 - 0.25 -
0.90 - 1.40 1.00 2.00 26.0 - 32.0 1.00 3.00 balance 3.0 - 6.0 3.00 -
0.150 2.000 0.045 0.030 1.000 16.0 - 18.0 2.0 - 3.0 10.0 - 14.0 -
29
Technical Information
AIL
113 133 163 193 1A3 413 433 463 493 4A3 713 733 763 793 7A3
KITZ
K150SCL K300SCL K600SCL K900SCL K1500SCL K150SCJ K300SCJ K600SCJ K900SCJ K1500SCJ K150SCO K300SCO K600SCO K900SCO K1500SCO
VELAN
F-0064C02 F-1064C02 F-2064C02 F-3064C02 F-4064C02 F-0074C02 F-1074C02 F-2074C02 F-3074C02 F-4074C02 F-0114C02 F-1114C02 F-2114C02 F-3114C02 F-4114C02
DSI
37 23 66 73 77 133 141 161 137 149 177 -
NEWCO
11F-CB 13F-CB 16F-CB 19F-CB 21F-CB 23F-CB 26F-CB 31F-CB 33F-CB 36F-CB 39F-CB -
Gate Valve
Globe Valve
Check Valve
Type
AIL
KITZ
VELAN
DSI
NEWCO
WALWORTH
TONG YONG
13% Cr. SS 304 HF 13% Cr. + HF SS 316 SS 316 + HF SS 316 & HF Monel
1 2 5 8 10 12 16 9
N/A PS TY NB -
X U XU LU A
1 3 2 4 -
AA HF UT 18-8 A
30
Global Recognition
International Clientele
AIL Cast Steel Valves have been supplied over the years, to the following end-users and EPC Contractors :
ADNOC ARCO BASF BP CALTEX CHEVRON CITGO DSM ENGEN ENOC EQUILLON EXXONMOBIL FORMOSA PLASTICS GASCO KNPC KOC MOTIVA
NOVACOR PDVSA PETROCANADA PETRONAS PNOC, PHILIPPINES QATAR PETROLEUM SAPREF SASOL SAUDI ARAMCO SHELL STAR SUNOCO SYNCRUDE TEXACO TOTALFINAELF UNION CARBIDE UNOCAL
ABB AMEC BECHTEL CMI CONTRINA FLUOR DANIEL FOSTER WHEELER JACOBS JGC KELLOG, BROWN & ROOT KRUPP UHDE KVAERNER LINDE PARSONS PETROFAC SNAM PROGETTI TECHNIP
31
Mount-Poonamallee Road, Manapakkam, Post Bag 976, Chennai 600 089, INDIA. Tel : +91 (44) 2492323. Fax : +91 (44) 2495055, 2494055. Website : www.ailvalves.com
Manufacturing Plants
Mount-Poonamallee Road, Manapakkam, Chennai 600 089, INDIA. Enathur, Kancheepuram 631 552, INDIA.
PB No. : C2024-0/01.02 As we continuously endeavour to improve our products, the data given herein are subject to change without notice.