Escolar Documentos
Profissional Documentos
Cultura Documentos
Australian StandardR
TOILET SEATS
OF MOULDED PLASTICS
METRIC UNITS
This standard, prepared by Committee PL/12, Plastics Toilet Seats, was approved on behalf
of the Council of the Standards Association of Australia on 19 July 1973.
Review of Australian Standards. To keep abreast of progress in industry, Australian Standards are subject to
periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important
therefore that Standards users ensure that they are in possession of the latest edition, and any amendments thereto.
Full details of all Australian Standards and related publications will be found in the Standards Australia Catalogue
of Publications; this information is supplemented each month by the magazine ‘The Australian Standard’, which
subscribing members receive, and which gives details of new publications, new editions and amendments, and of
withdrawn Standards.
Suggestions for improvements to Australian Standards, addressed to the head office of Standards Australia, are
welcomed. Notification of any inaccuracy or ambiguity found in an Australian Standard should be made without
delay in order that the matter may be investigated and appropriate action taken.
Australian StandardR
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
TOILET SEATS
OF MOULDED PLASTICS
SPECIFICATION Page
1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Workmanship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7 Test Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8 Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
9 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
APPENDICES
A Method for Determination of Water Absorption of Seats or Flaps . . . . . . . . . . 11
B Method for Determination of Impact Resistance of Seats . . . . . . . . . . . . . . . . 12
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
1 SCOPE. This specification applies to plastics toilet seats and flaps for sanitary
water closet pans complying with AS 1172. It includes essential requirements for
This is a free 6 page sample. Access the full version at http://infostore.saiglobal.com.
3 MATERIALS.
3.1 Plastics Materials for Seats and Flaps. Plastics materials used in the
manufacture of seats and flaps shall be such that under normal conditions of use the
seats and flaps shall be —
(a) resistant to abnormal deterioration of properties, and appearance by ageing;
(b) capable of being easily cleaned and not adversely affected by urine, common
solvents, dilute acids or alkalis, or non-abrasive household cleansers;
(c) capable of meeting the test requirements detailed in Tables 1 and 2.
3.2 Buffer Materials. Any buffers of seats and flaps shall be of resilient synthetic
or natural rubber or equivalent plastics material and shall be non-absorbent. The
material shall be compatible with the constructional materials which they may contact
in service.
3.3 Materials for Hingeing Devices and Bolts and Nuts.
3.3.1 Stainless steel. All stainless steel parts shall be made of stainless steel of the
18 per cent chromium and 8 per cent nickel type in accordance with the requirements
of AS G18*.
3.3.2 Copper alloys. If plated, copper alloys shall be nickel-chromium electroplated
to Service Condition Number 2 of AS 1192†. Unplated copper alloys, corrosion
resistant to materials likely to be contacted in service, may be used.