Escolar Documentos
Profissional Documentos
Cultura Documentos
Pemba
W510
Specifications
SA Date: Q1 2007
Form Factor: Clam Shell
Antenna: Internal
Bands/Modes: GSM Quad Band (GSM 850/900/1800/1900 MHz),
EDGE Class 12, GPRS Class 12 (4U/4D), BT Class 2
Size: ~ 70cc
Weight: ~ 107g
Dimensions: 99 x 46 x 17.5mm
Display: 1.9”, 176 x 220, 262k Color TFT, Main Display
1.0”, 96 x 80, 65k Color CSTN, CLI Display
Specifications
Design Overview
Earpiece Navi & Keypad
MAIN display
VR Key
CLI display
USB Connector
1.3MP Camera Cover
Battery Cover
Vol Up/Down
Speaker
Mic
Accessories
Disassembly Procedures
• Main Housing
1. 2.
Battery
Cover
Battery
Slot
- Push the Battery Cover in the - Push inwards at the battery slot area &
direction shown lift up the Battery completely.
3. 4.
Front
Housing
SIM Card Cap
Disassembly
Tool
- Slide out the SIM card in the - Using the disassembly tool, slides
direction shown. it along the Front Housing Cap to
release the catches.
catches
5. 6.
6 x T5 screws
7. 8.
-Lift up the Rear Housing & separate - Remove the Connector Grommet.
it from the Front Housing.
9. 10.
B2B Connector
- Remove the B2B Connector using - Lift up the Main Board from the Front
the disassembly tool. Housing.
11. 12.
- With the Flip opened, push out the - Using a tweezer, remove the Cap
Keypad from the Front Housing. Lock from the Front Housing.
Disassembled Parts
Disassembly Procedures
• Flip
1. 2.
Left
Knuckle
Right
Knuckle
(Lanyard)
- Insert the tweezer into the slot for - Insert the tweezer into the slot
the Right Knuckle Cap. (above the Flex Cable) for Left
- Push outwards. Knuckle Cap.
- Carefully pushing it outwards.
3. 3a.
3b. 4.
Flex Cable
Screw Bumper
- Carefully separate the Front Housing - Remove the Screw Bumper (4pcs)
from the Flip Assy by pushing the on the Rear Flip Housing using a
Flex Cable outwards. tweezer.
- Ensure that the Flex Cable is not
damaged.
5. 6.
4 x T5 Screws
- Using the T5 screw driver, unscrew the - Insert the disassembly tool into the
4 Flip screws. slot area.
- Move along the Flip Housing to
(Torque force : 1.0 +/- 0.1 lbf-in)
release the catches.
7. 8.
9. 10.
10a. 11.
Flex
Connectors
Side Hooks
- Lift the bracket away from the Flip - Remove the Hinge Flex Cable by
PCB. sliding it away from the Flip Housing
- Careful not to cause damage to the slot.
Flex Connectors.
12. 13.
- Using the plastic tool, carefully - With the plastic tool, lift up the Flip
remove the Receiver as shown. PCB from the Flip Rear Hosuing.
14. 14a .
- Using the plastic tool, disengage the - With a light push, separate the Main
Flex Connector for the Main LCD LCD from the bracket.
from the Flip PCB.
15. 15a.
ZIF connector
- Remove the Kapton Tape covering - Unlatch the ZIF Connector Catch.
the CLI Flex Circuit.
15b. 15c.
Adhesive underneath
The Flex Circuit
- Using the plastic tool, carefully work - Give a light push from behind the
along the adhesive on the Flex CLI Lens to separate it from the PCB.
Circuit to separate it from the Flip
PCB.
16. 16a.
- Leverage with the plastic tool in the - Perform the same action on the
direction shown. other side of the Camera Module.
- Both action is done to separate the
adhesive underneath.
Disassembled Parts