Escolar Documentos
Profissional Documentos
Cultura Documentos
FTV2.3
POWER SUPPLY
REPAIR METHOD
Check VS and VA Output Load Chapter 09 page 2
SERVICE TIP:
If the Vs input of the PDP is short circuited a simple test can be done:
Disconnect the set from the mains.
Disconnect ALL cables between PSU and PDP.
Connect a regulated DC power supply (current limited to 1 A) directly to the Vs input of the YSUS board of the
PDP (pin 9 of connector CN 33) and the chassis of the FTV.
Ramp-up the voltage slowly to maximal 5 V. If the current increases to 1 A, the PDP is defect.
The same can be done for the Vs input on the XSUS board: pin 10 of connector CN 23.
The Va inputs on the various boards can also be checked with the same procedure:
The tests must be done on the connectors
CN23: pin 1 (XSUS-board)
CN42: pin 1 (ABUSR-board)
CN52: pin 1 (ABUSL-board).
The next pages explains how to repair the power supply outside the
set, with fictive loads
Repair The Power Supply Out the Set Chapter 09 page 3
Connect VCEGO (p13) and VSAGO (p15) of CN307 to a +2,5V from the +3,3v STBY SW.
For a regulated output voltage, connect test point VRS (pin 7) and VRA (pin 9) of CN307 to + 1V.
Connect to the two solder island near connector 307 (flex foil connector).
Load Vcc (5V) with resistor 8,2 Ohm, the Max load for VCC = 7A.
Pin 9
Power OK
P7
P3
Flow Chart Overview Check Points Chapter 09 page 5
Check+V
Check +Vstandby
standbypower
powersupply,
supply,++3,3V
3,3Vand
and+5V
+5Vstby
stbyon
onCN319.
CN319.
CheckPreconditioner
Check Preconditioner+395V
+395Von
onfuse1004.
fuse1004.
Check+Vs
Check +Vsswitched
switchedoutput
outputvoltage
voltageon
onpin
pin8,9,10
8,9,10CN323
CN323or
orpin
pin7,8,9
7,8,9CN333
CN333
around80……85V
around 80……85V
Check++Va
Check Vaoutput
outputvoltage
voltageon
onpin
pin11CN323
CN323==around
around50….55V
50….55V
Check++Vcc
Check Vccoutput
outputvoltage
voltageon
onpin
pin11CN333
CN333==5,2V
5,2V
Check++3V3
Check 3V3output
outputvoltage
voltageon
onpin
pin8,9,10,11,12
8,9,10,11,12of
ofCN305
CN305==3,3V
3,3V
CheckPower
Check PowerOK
OKline
lineon
onpin
pin99CN319,
CN319,must
mustbe
behigh
high(4,5V).
(4,5V).
Switched Standby Voltages Chapter 09 page 6
in Ic7500
Pin 5 Dra
drain IC7500?
<100V
>100V
Fus.1400,
Check also
Check secondary part
the +25V Hot from Stby PS
Short circuit and
Reference is primary ground
Control loop
P2
Check Preconditioner Chapter 09 page 8
Drain T7610
Pin 11 Gate
Pin 13 oscil.
Preconditioner output
Fuse 9004 = 395V
P5
Check Preconditioner Chapter 09 page 9
Check on IC7650
•Pin 12 Vcc = 14,5V
Pin 11 Gate
Standby supply is switched on and is in continous mode, 3,3V and 5V standby are OK Diagram P2
VCEGO and VSAGO are connected to 2,5V Check Load on standby supply
Diagram P3
Diagram P2
Supply_on line = H and T7460, T7465 and T7470 conducts
P2
Diagram P5
P5
395V Preconditioner is OK
Diagram P6
25V_Hot Standby Supply is OK
P6
SW25V_Hot from preconditioner is OK
Check +16V provided by Ic7093
+Vs switched
4
on pin 10 CN323
Vs=70+10Vrs
Pin 3 and 6 T5002 = around 80 …85V
or C2011/C2017
P6
Check LLC Supply Control Part IC7001 Chapter 09 page 12
•5 Vref = 5,1V
P6
The + to the output of IC7093 (metal part), - to primary ground on cooling plate LLC
Adjust the current output of the external DC power supply to 100mA max
OA and OB
One shot
oscil 4,3V
17V
2,7V OA
IC7001
Ref 5,1V MC34067P OB
1,8V 4,9V
4,9V 0,6V
P6 4,9V
VS Switch & Sequence Discharge Circuit Chapter 09 page 15
Start Up Sequence
Switch Off Sequence
T7050 blocks
T7050 conducts
P7
T7052 conducts andVS is directly discharged,
Vs is switched while VA is discharged if VS is lower than VA
Sart Up Conditions VA Supply Chapter 09 page 16
Diagram P3
VSAGO is connconnected to +2,5V
P7 Start up VA
Check VA Supply Chapter 09 page 17
VA Control Ic7112
Va=30+20Vra
= around 50…..55V.
CN323 P7
VCC Supply Start up Conditions Chapter 09 page 18
LLC is OK
Diagram P3
CN307 pin 13 VCEGO=2,5V P3
CN323
P7
Control IC7712
3V3 Start up Conditions Chapter 09 page 20
Diagram P6
+18V from LLC supply is OK
P7
3,3V Supply Chapter 09 page 21
P7
3V3 Power Supply Repair With External DC Power
Chapter 09 page 22
Supply
Oscillator pin 1
Vcc = 19V
Pin 16 = 5,1V.
Pin 17 SS = 18V
Pin 11 = 0,7V
P7
Pin 12 = 3,2V (if power supply is OK)
Alignment Vs and Va After Power Supply Repair Chapter 09 page 23
VA adjust R3127
Please keep in mind that in case of the following combinations between PSU's and PDP's no or almost no
alignments are needed of the Vs and Va:
PDP with only the Vs feedback loop (-52 in type number of PDP) in combination with the .3 PSU: Keep the SW
feedback loop OFF and align both the Vs and Va as described in the Service manual.
PDP with only the Vs feedback loop (-52 in type number of PDP) in combination with the .3 PSU with precision
resistors: The SW feedback loop can be switched on and then the Va has to checked and aligned with an accuracy of
+/- 1,5V and the potentio meter of the Vs should be positioned in the middle. No further alignments needed.
PDP with only the Vs feedback loop (-52 in type number of PDP) in combination with the .4 PSU: Switch on the SW
feedback loop and no further alignments are needed.
PDP with the Vs & Va feedback loop (a "B" in the type number of PDP) in combination with the .3 PSU: Keep the SW
feedback loop OFF and align both the Vs and Va as described in the Service manual.
PDP with the Vs & Va feedback loop (a "B" in the type number of PDP) in combination with the .3 PSU with precision
resistors: Switch on the SW feedback loop and no further alignments are needed.
PDP with the Vs & Va feedback loop (a "B" in the type number of PDP) in combination with the .4 PSU: Switch on the
SW feedback loop and no further alignments are needed.
valere.deseranno@philips.com