Escolar Documentos
Profissional Documentos
Cultura Documentos
Fall 2010
Shahab Gerami
Phase
The concept of a closed system is of major interest in applied hydrocarbon thermodynamics. It is called a homogeneous closed system if it contains a single phase, e.g. a natural gas phase or an oil phase. A heterogeneous closed system contains more than one phase. Phase: a phase is defined as a physically homogeneous portion of matter.
The phases of a heterogeneous system are separated by interfaces and are optically distinguishable. It is not obligatory that a phase is chemically homogeneous. It may consists of several compounds, e.g. of a large number of various hydrocarbons.
Property
A property is a characteristic of a system to which numerical values can be assigned to describe the system (Mass, Temperature, Pressure ,Density,...) Property: 1. Extensive Property: Extensive properties are properties which can be counted and their value for the whole system is the sum of the value for subdivisions of the system. They depend on the extent of the system. Examples: Volume, Mass
2. Intensive Property: Intensive properties are independent of the size (mass or volume) of the system. Examples: Density, Temperature
Property
State
The state of a system is defined by the values of its properties. A system is in equilibrium if its properties are not changing at any given location in the system. This is also known as thermodynamic equilibrium or total equilibrium. Equilibrium implies balance--no unbalanced potentials (driving forces) in the system. We will distinguish four different types of equilibrium
1. 2. 3. 4.
Thermal equilibrium -- the temperature does not change with time Mechanical equilibrium -- Pressure does not change with time Chemical equilibrium -- molecular structure does not change with time Phase equilibrium mass and composition of each phase is unchanging with time (i.e., same liquid/gas or liquid/solid composition)
State Functions
State functions or state variables are those properties for which the change in state only depends on the respective initial and final state. It is this path-independent characteristic of the state functions that makes it possible to quantify any change of a system.
1 ath ath 1
ath
10
Equilibrium
Equilibrium has been defined as a state of rest. In an equilibrium state, no further change or - more precisely - no net-flux will take place unless one or more properties of the system are altered. On the other side, a system changes until it reaches its equilibrium state. Any change of a system is called a thermodynamic interest in the thermodynamic study of the system: adiabatic (no heat added to or removed from the system), isothermal (constant temperature), isobaric (constant pressure), isochoric (constant volume). A process is called reversible if it proceeds through a series of equilibrium states in such a way that the work done by forward change along the path is identical to the work attained from the backward change along the same path. However, all real processes are irreversible with varying degrees of departure from a reversible one.
11
Temperature Scales
Phase Behavior
Hydrocarbon reservoirs = Rock + Fluids Reservoir Fluid: Water in brine form and a gaseous and/or liquid hydrocarbon phase are regarded as reservoir fluids. The phase behavior of the actual hydrocarbon mixture in the reservoir can be described as a function of the state of the system. A system in thermodynamic equilibrium possesses an accurately defined relationship between the state variables. These are united in the so-called equation of state:
14
Phase Diagram
A phase diagram is a concise graphical method of representing phase behavior of fluids. It provides an effective tool for communicating a large amount of information about how fluids behave at different conditions. Two Classes of Fluids 1. Pure-component systems: the composition is not a variable and therefore cannot influence behavior. 2. Mixtures: the behavior of a mixture is strongly controlled by composition. In fact, as the number of components in the system increases, the complexity of the phase diagram increases as well. Two components Multi components
15
The curve in Figure 1 is called the vapor pressure curve or boiling point curve. The line also represents the dew point curve and the bubble point curve; one on top of the other. This curve represents the transition between the vapor and liquid states.
16
Figure 1
17
Figure 1
In Figure 1, once a saturation pressure has been selected, there is one (and only one) saturation temperature associated with it. This is only true for a single component system. In other words, this is the only temperature (at the given pressure), at which liquid and gas phase will co-exist in equilibrium. The rule that governs the uniqueness of this point, for a single-component system, is called the Gibbs Phase Rule. 18
Figure 2
Two very important thermodynamic points bound the vapor pressure curve: the Critical Point at its upper end and the Triple Point at its lower end.
19
Triple Point
The Triple Point is the meeting point of the vapor pressure, solidification and sublimation curves; hence, it represents the only condition at which all three phases of a pure substance (solid, liquid and gas) can co-exist in equilibrium.
Figure 2
For water, the triple point is at 273.16 K (0.01 rC or 32.018 rF) and 0.6113 kPa (0.0887 psia).
20
Critical Point
At the Critical Point, gas and liquid are in equilibrium without any interface to differentiate them; they are no longer distinguishable in terms of their properties. As we recall, the only location on the P-T diagram where liquid and gas can be found together in equilibrium is along the vapor pressure curve. Hence, the critical point is clearly the maximum value of temperature and pressure at which liquid and vapor can be at equilibrium. This maximum temperature is called the critical temperature (Tc); the corresponding maximum pressure is called the critical pressure (Pc). The critical point is the point at which all intensive properties of the gas and liquid phases are equal. An intensive property is a property independent of the quantity of the system. Pressure, temperature, density, composition, and viscosity are examples of intensive properties.
Figure 3
21
22
The phase boundary represents a sharp discontinuity in density (and other physical properties)
the phase boundary is NOT crossed at all Path AD: Isothermal compression Path DE: Isobaric heating Path EB: Isothermal expansion We went from an all-liquid condition (point A) to an all-vapor condition (point B) without any sharp phase transition.
23
Sensible Heat: Its main purpose is to cause an increase in temperature of the system. Latent Heat: It serves only one purpose: to convert the liquid into vapor. It does not cause a temperature increase.
L+V
The temperature is being held constant; Isothermal compression process path F-G: two-phase condition, the liquid (L) and vapor (V) co-exist in equilibrium E: all-vapor condition F: saturated vapor condition (vapor in equilibrium with an infinitesimal amount of liquid; dew pint G: saturated liquid condition (liquid in equilibrium with an infinitesimal amount of vapor; bubble point
24
25
26
27