Escolar Documentos
Profissional Documentos
Cultura Documentos
2 Adjustment environment
1) Temperature: 15oC -35oC
2) Relative humidity: 45-75%
3) Air pressure: 86-106KPa
3. Test Equipment (The following equipment should be calibrated correctly.)
1) Oscilloscope
2) Multi-meter (Internal resistance: DC≥20kΩ/V AC≥5kΩ/V)
3) High voltmeter 35kV
4) Ammeter (0.5 grade, at DC 3mA position)
5) Degaussing coil
6) PHILIPS pattern signal generator (PH5820 or FLUKE 54200 or similar type
apparatus)
4 Adjustment items and adjustment operation
4.1 AC power supply check and +B adjustment
4.1.1 Check AC power supply is normal or not (220V, 50Hz and Sine Wave are normal)
4.1.2 Receive Television broadcast signal, set PICTURE to standard mode
4.1.3 Adjust RP950 so that voltages at two ends of C960 are +B, the voltage of +B
please refer to BOM
4.2 High voltage check and filament voltage check
4.2.1 Make sure AC power supply and +B are within pointed range before calibrating
high voltage.
4.2.2 Connect high voltmeter to anode (G4) of CRT.
4.2.3 Turn on the TV set, set the BRIGHTNESS and CONTRAST to the minimum, and
switch to AV mode (No any signal applied).
4.2.4 High voltage please refer to the related CRT’s spec.
4.2.5 Filament voltage measured by virtual value meter should be about 6.3 ±
0.2Vrms.
4.3 Grid voltage adjustment
4.3.1 Set PICTURE to standard mode, and switch to AV mode. Input a black signal.
EK-L
第 2 张
with the data in computer.
4.7.3 Exit to operation mode, and set Color temp to Cold (12000K), then enter into
factory menu FAC3, check whether the data of cold temperature is
the same with the data in computer.
4.7.4 According to 4.7.3, check whether the data of warm temperature is the same
with the data in computer.
Standard:Color temperature 9300K (X=0.284 Y=0.299) FAC3
Cold: Color temperature 12000K(X=0.272 Y=0.279) FAC3
Warm: Color temperature 6500K (X=0.313 Y=0.329) FAC3
BLOR-N XX BLOR-W XX BLOR-C XX
BLOG-N XX BLOG-W XX BLOG-C XX
BLOB-N XX BLOB-W XX BLOB-C XX
WPR-N XX WPR-W XX WPR-C XX
WPG-N XX WPG-W XX WPG-C XX
WPB-N XX WPB-W XX WPB-C XX
EK-L
第 3 张
item description range Default
value
Initialize
INIT TV 0,1 0
memory’s data
Watch Dog
WDT 0: Disable, 0,1 0
1: Enable
Childlock Style
CHILDLOCK 0: Disable, 0,1 1
Factory 1: Enable
PAGE – 0 Calendar
CALENDAR 0: Disable, 0,1 1
1: Enable
Game
CAME 0: Disable, 0,1 1
1: Enable
P. TIME Switch
TIM-SKIP 0: Disable, 0,1 0
1: Enable
Program browse
SCAN 0: Disable, 0,1 1
1: Enable
Version
STEREO-80 1
Information
VOLUME-MAX Set max volume 0..63 42
Set the value of
VOLUME-5 0..63 10
volume 5
Set the value of
VOLUME-15 0..63 25
volume 15
Set the value of
VOLUME-25 0..63 35
volume 25
Set the value of
VOLUME-45 0..63 40
Factory volume 45
PAGE - 4 Set the value of
VOLUME-55 0..63 50
volume 55
Automate volume
limit
AVL 0,1 0
0: Disable,
1: Enable
Volume down mute
MUTE VOL- 0: Disable, 0,1 1
1: Enable
Min contrast
CON-MIN 0..63 0
setting
Mid contrast
CON-MID 0..63 32
setting
Max contrast
CON-MAX 0..63 63
setting
Min brightness
BRI-MIN 0..63 0
setting
Factory Mid brightness
PAGE - 5 BRI-MIN 0..63 32
setting
Max brightness
BRI-MAX 0..63 63
setting
Min color
COL-MIN 0..63 0
setting
EK-L
第 4 张
Mid color
COL-MID 0..63 32
setting
Max color
COL-MAX 0..63 63
setting
Factory Min sharpness
PAGE - 6 SHA-MIN 0..63 0
setting
Mid sharpness
SHA-MID 0..63 32
setting
Max sharpness
SHA-MAX 0..63 63
setting
Chroma BPF
center frequency
CB 0,1 0
0: Fsc,
1: 1.1×Fsc
Adjust OSD’s
RGB 0..31 15
brightness
Adjust cathode
CL 0..15 8
level
Sub-brightness
VSD BRI 0..63 34
adjustment
The same as VSD
VSD 0..63 34
Bright
PAL selection
PAL MN 0: Disable, 0,1 1
1: Enable
DCXO Adjust DCXO 0..3 1
VIF selection
MONO
0:38.00MHz
1: 45.75MHz
2: 38.90Mhz
3: 33.90Mhz
Factory AVS/STREO
PAGE – 7
0:58.75MHz
IF 1:45.75MHz 0..3/7 1
2: 38.90MHz
3: 38.00MHz
4: 33.40MHz
5: 42.00MHz
6: 33.90MHz
7: 48.00MHz
M selection
OIF 0: Disable, 0,1 1
1: Enable
RF AGC
AGCT 0..63 33
adjustment
Protection
PROTECT 0:No protection 0,1 1
1:Protection
EK-L
第 5 张
Power on key
0: Standby,
PWR-CH 1: Standby, 0,1 1
PROG. up/down,
digits
Power on mode
0:always be
PWR-ON standby, 0,1 1
1:Restored to
the last state
Stand-by time
PWR-TIM 0-3 0
adjustment
Switch channel
0: Not enter
INCL-AV 0,1 0
into AV mode,
1: Enter into AV
AV1 input
AV1 0: Disable, 0,1 1
1: Enable
AV2 input
AV2 0: Disable, 0,1 0
1: Enable
S-video input
SVHS 0: Disable, 0,1 0
Factory 1: Enable
PAGE – 8 YCbCr input
YCBCR 0: Disable, 0,1 1
1:Enable
AV3 input
AV3 0: Disable, 0,1 0
1:Enable
AV input ports
PCB-NEW 0,1 0
swith
Switch channel
CH BLACK 0: Disable, 0,1 1
1: Enable
Black saver off
SCR BLACK 0: Disable, 0,1 0
1: Enable
OSD English
Factory selection
ENGLISH 0,1 1
PAGE – 9 0: Disable,
1: Enable
OSD French
selection
FRENCH 0,1 1
0: Disable,
1: Enable
OSD Spanish
selection
SPANISH 0: Disable, 0,1 1
1: Enable
EK-L
第 6 张
OSD Portugal
selection
PORTUGAL 0,1 1
0: Disable,
1: Enable
Close caption
CC decoder 0,1 1
0: Disable,1:
Enable
Childlock Style
VCHIP 0: Disable, 0,1 1
1: Enable
EK-L
第 7 张
PDF 文件以 "PDF 制作工厂" 试用版创建 http://www.fineprint.com
PDF 文件以 "PDF 制作工厂" 试用版创建 http://www.fineprint.com