Escolar Documentos
Profissional Documentos
Cultura Documentos
MESIN-MESIN LISTRIK
SLIP-RING INDUCTION MOTOR 1
DISUSUN OLEH
DIKI RIANDY
2105031045
EL-5A
i
DAFTAR ISI
ii
PRAKTIKUM MESIN-MESIN LISTRIK
SLIP-RING INDUCTION MOTOR 1
K L M
rpm
U2 V2 W2 I2
F2 A2
A A
K
L
G TG M
M
F1 A1
U1 V1 W1
U1 V1 W1
Y
R S T
U V W
Z
R S T
V P
I
RB
V
I1
L1 L2 L3
220 V = 3 x 0-230 V
F MV 1300 F MV 1300
A. Equipment
3
𝑇 = Current transformer 10/1 A MV 1931
Y = Star-delta switch MV 1503
Z = Reversing stanter MV 1502
S = Switch MV 1500
F = Power Pack MV 1300
B. Procedure
a) Connecting up
1. Connect the torque meter as generator and the induction motor as motor as shown
in figure 6-3. Switch S must be off and the other two switches is position “Forwad”
and “∆”.
2. Make a node of the ratings of the induction motor shown on the rating plate.
3. The supervisor should now check all connections before switching on power.
1. Set the rotor Starter to minimum resistance and switch on the AC Voltage. Hold
the rotor (use protection gloves) with the hand and turn up the voltage to 50V.
Make a note of current. Turndown the voltage to zero.
2. Set the rotor starter to maximum resistance. Hold the rotor with the hand an turn
up the voltage to 50V. Make a note of the current 𝐼𝑎 . Turn down the voltage to
zero.
3. Set the rotor starter to minimum resistance and the star/delta-switch to Y. Hold the
rotor with the hand and turn up voltage to 50V. Make a note of the current. Turn
down the voltage and turn off the voltage switch.
c) Plugging
1. Set the rotor starter to maximum resistance, star/delta-switch to “∆” and the
reversing satarter to forwad. Switch on the AC voltage, the motors starts. Slowly
turn off the rotor starter.
2. Adjust the voltage V to 230 V and keep it constant during the measurements. Read
V, 𝐼1 , P,T, 𝑛2 , and the rotor frequency on the ammeter 𝐼2 . Check that the load
resistor 𝑅𝑠 is set to minimum current. Turn on switch S and the DC voltage.
4
3. Vary the load with the shunt rheostat of thetorque meter and the load resistor 𝑅𝑆 in
steps of 1 Nm up to 7.5 Nm. For each step,make a note of V, 𝐼1 P, T, 𝑛2 and 𝑓2 .
4. Adjust the load resistor to minimum current. Turn off switch S.
e) Speed control
1. Adjust the rotor starter so that roughlty half of its resitance is connected to the rotor
circuit. When using starter MV 2636, set the switch to R2.
2. Repeat measurments A to D.
3. Switch off the 220v DC and 230/133V AC.
5
D. Tables
Rated power = 1,5 KW
Rated speed = 1440 rpm
6
E. Analisis
1. 𝑃𝑜𝑢𝑡 = 952 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,10 𝑥 0,85
= 2065,56 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
952
= 2065,56 𝑥 100%
= 0,461
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1450
= 𝑥 100%
1500
= 0,033
2. 𝑃𝑜𝑢𝑡 = 1020 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,16 𝑥 0,85
= 2085,87 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1020
= 𝑥 100%
2085,87
= 0,489
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1450
= 𝑥 100%
1500
7
= 0,033
3. 𝑃𝑜𝑢𝑡 = 1116 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,03 𝑥 0,85
= 2041,85 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1116
= 2041,85 𝑥 100%
= 0,546
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1450
= 𝑥 100%
1500
= 0,033
4. 𝑃𝑜𝑢𝑡 = 1028 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,48 𝑥 0,85
= 2194,23 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1028
= 2194,23 𝑥 100%
= 0,468
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑁𝑠
𝑥 100%
1500 − 1450
= 𝑥 100%
1500
8
= 0,033
5. 𝑃𝑜𝑢𝑡 = 1386 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,87 𝑥 0,85
= 2326,29 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1386
= 2326,29 𝑥 100%
= 0,596
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1450
= 𝑥 100%
1500
= 0,033
6. 𝑃𝑜𝑢𝑡 = 1386 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,87 𝑥 0,85
= 2528,58 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1386
= 2528,58 𝑥 100%
= 0,548
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1450
= 1500
𝑥 100%
= 0,033
9
7. 𝑃𝑜𝑢𝑡 = 1470 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 7,1 𝑥 0,85
= 2404,17 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1470
= 2404,17 𝑥 100%
= 0,611
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1450
= 𝑥 100%
1500
= 0,033
8. 𝑃𝑜𝑢𝑡 = 1512 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 7,21 𝑥 0,85
= 2441,42 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1512
= 2441,42 𝑥 100%
= 0,619
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1450
= 1500
𝑥 100%
= 0,033
10
Hasil perhitungan 6.4.5
(rotor stator pada kondisi 1⁄2)
1. 𝑃𝑜𝑢𝑡 = 928 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6 𝑥 0,85
= 2031,69 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
928
= 2031,69 𝑥 100%
= 0,457
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1400
= 𝑥 100%
1500
= 0,067
2. 𝑃𝑜𝑢𝑡 = 1009 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,12 𝑥 0,85
= 2072,33 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1009
= 2072,33 𝑥 100%
= 0,487
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1350
= 𝑥 100%
1500
= 0,1
11
3. 𝑃𝑜𝑢𝑡 = 1090 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,19 𝑥 0,85
= 2096.03 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1090
= 2096.03 𝑥 100%
= 0,52
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1280
= 𝑥 100%
1500
= 0,147
4. 𝑃𝑜𝑢𝑡 = 1185 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,38 𝑥 0,85
= 2160,37 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1185
= 2160,37 𝑥 100%
= 0,55
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1240
= 1500
𝑥 100%
= 0,173
12
5. 𝑃𝑜𝑢𝑡 = 1264 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,52 𝑥 0,85
= 2207,77 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1264
= 2207,77 𝑥 100%
= 0,57
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑁𝑠
𝑥 100%
1500 − 1180
= 𝑥 100%
1500
= 0,213
6. 𝑃𝑜𝑢𝑡 = 1370 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 6,81 𝑥 0,85
= 2305,97 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1370
= 2305,97 𝑥 100%
= 0,59
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1120
= 𝑥 100%
1500
= 0,253
13
7. 𝑃𝑜𝑢𝑡 = 1455 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 7,04 𝑥 0,85
= 2383,86 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1455
= 2383,86 𝑥 100%
= 0,61
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑁𝑠
𝑥 100%
1500 − 1050
= 𝑥 100%
1500
= 0,3
8. 𝑃𝑜𝑢𝑡 = 1505 W
𝑃𝑖𝑛 = √3 𝑥 𝑉𝑥 𝐼 𝑥 cos 𝜃
= √3 𝑥 230 𝑥 7,16 𝑥 0,85
= 2424,49 W
𝑃𝑜𝑢𝑡
%𝑛 = 𝑥 100%
𝑃𝑖𝑛
1505
= 𝑥 100%
2424,49
= 0,62
50
𝑁𝑠 = 120 𝑥 4
= 1500
𝑁𝑠−𝑁
%𝑆 = 𝑥 100%
𝑁𝑠
1500 − 1020
= 𝑥 100%
1500
= 0,32
14
F. Jawaban
1. Sudah ada pada bagian analisis di halaman sebelumnya.
2. Diketahui pada tabel 6.4.4 dan tabel 6.4.5 adalah sebagai berikut.
Pout η = f.(Pout) Pout η = f.(Pout)
No f Tabel 6.4.4 Tabel 6.4.5
1 50 952 47600 928 46400
140000
120000
100000
80000
60000
40000
20000
0
1 2 3 4 5 6 7 8 9
η = f.(Pout) η = f.(Pout)
15
3. Gambar grafik nilai torsi pada tabel percobaan 6.4.4 dan 6.4.5
grafik torsi
0.35
0.3
0.25
0.2
S(%)
0.15
0.1
0.05
0
0 1 2 3 4 5 6 7 8
T ( Nm )
S ( % ) TABEL 6.4.5 S (%) TABEL 6.4.4
16
6. Gambar diagram rangkaian start delta dan revesing starter
Diagram rangkaian Start Delta
Keterangan gambar:
17
gambar A: Saya sudah menambahkan thermal overload dan 2 kontaktor dalam
rangkaian, yaitu K1 dan K2. Dalam gambar A ini K1 dalam posisi NC atau
sedang dalam kondisi ON, dan K2 dalam posisi Off. Lihatlah bagaimana urutan
phasa input R-S-T masuk dalam rangkaian, sehingga putaran motor menjadi
kearah kanan.
gambar B: Dalam gambar B ini urutan phasa input yang masuk dalam rangkaian
adalah kebalikannya, yaitu T-S-R bila K2 dalam posisi NC atau ON, dan K1
dalam posisi Off. Dan membuat arah putaran motor menjadi kearah kiri.
Fungsi dari saklar tersebut ialah Untuk membalik arah putaran motor star delta
sebenarnya sama saja dengan membalik putaran motor induksi 3 fasa yang
beroperasi dalam koneksi delta ataupun motor induksi 3 fasa yang beroperasi
dalam koneksi star, yaitu dengan membalik salah satu tegangan yang masuk ke
motor. Namun dalam metode start star delta, motor 3 fasa tersebut dioperasikan
dalam kedua koneksi yaitu koneksi star pada mula startnya dan setelah itu
berganti dengan koneksi delta. karena hal itu akan ada 6 terminal pada motor
yang didesain untuk metode start star delta.
7. Starting current
Hubungan delta
3) Minimal rotor stater :
IM = 1,55 A
IR = 0,66 A
4) Maksimal rotor stater :
IM = 7,9 A
IR = 4,6 A
Hubungan star
2) Minimal rotor stater :
IM = 0, ,52 A
IR = 0,39 A
18
G. Kesimpulan
1. Motor induksi 3 fasa rotor lilit adalah motor induksi yang lilitan rotor disambung
di luar motor. Sedangkan motor induksi 3 fas rotor sangkar adalah motor induksi
yang lilitan rotornya disambungkan di dalam bodi motor.
2. Motor rotor lilit, juga dikenal sebagai motor rotor cincin slip adalah jenis motor
induksi yang belitan rotornya terhubung melalui cincin slip ke tantangan luar.
3. Motor rotor sangkar memiliki putaran yang lebih tinggi dibandingkan motor
induksi rotor lilit. Dengan putaran yang lebih tinggi, berarti motor sangkar
memiliki torsi yang lebih rendah dibandingkan motor lilit.
4. Karakteristik kecepatan dan torsi motor rotor lilit dapat ditur dengan mengubah
hambatan luar, tidak seperti motor sangkar yang mempunyai karakteristik tetap.
5. Motor slip ring atu sering disebut motor rotor lilit termasuk motor induksi 3 phasa
dengan rotor belitan dan dilengkapi dengn slip ring yang dihubungkan dengan sikat
arang ke terminal. Motor slip ring dirancang untuk daya besar.
Diki Riandy
2105031045
19