Escolar Documentos
Profissional Documentos
Cultura Documentos
Manutenção Básica
(Comissionamento)
Referências
1
Objetivos
Conteúdo
2
Conectando a Alimentação -48 VDC
Características do CLI
return
3
Características do CLI
Características do CLI
Funções de Edição
O CLI provê funções de edição básicas. Isso habilita a edição multi-linha, com até
255 bytes por cada comando.
<↑> <↓> <Ctrl+P> Para mostrar histórico de comandos
Histórico de Comandos Guardados
4
Conteúdo
1. Utilizando a estrutura CLI
2. Configuração de Terminal de Manutenção
3. Gerência de Usuários
4. Gerência do Equipamento
Placas Controladoras
Placas Controladoras – MA5600 / MA5680 / MA5603 / MA5683
H801SCUB H801SCUF H801SCUH H801SCUK
10
5
Placas Controladoras
Placas Controladoras – MA5600 / MA5680 / MA5603 / MA5683
H801SCUL H801SCUN H801SCUV
11
Placas Controladoras
Placas Controladoras – MA5600 / MA5680 / MA5603 / MA5683
12
6
H801MCUD Placas Controladoras
Placas Controladoras – MA5608
H801MCUD1 H801MCUE
13
Placas Controladoras
Controladoras MPLA e MPLB da linha MA5800 X7, X15 e X17
MPLB
MPLA
14
7
Placas Controladoras
15
Placas Controladoras
Controladoras MPSA e MPSC da linha MA5800 X2
H901MPSC
H901MPSA
16
8
Placas Controladoras
MPSA
MPSC
MPLA e MPLB
Curso - Huawei MA560x Series – Operação e Configuração 17
Luiz Oliveira – CREA: 75436-D
17
Placas Controladoras
Board H901MPLA H902MPLA H903MPLA H901MPLB H902MPLB H901MPSC H901MPSA
Specifications
Bandwidth per slot 100 Gbit/s 100 Gbit/s 100 Gbit/s 200 Gbit/s 200 Gbit/s 80 Gbit/s 40 Gbit/s
(load balancing
mode)
Upstream or 4 x 10GE/GE ports 4 x 10GE/GE ports 4 x 10GE/GE ports 4 x 10GE/GE ports 4 x 10GE/GE ports 4 x 10GE/GE ports •2 x 10GE/GE
cascading port ports
•2 x GE ports
ALM port No No No No No Yes (7 Boolean value Yes (7 Boolean
inputs and 1 Boolean value inputs
value output) and 1 Boolean
value output)
BITS/TOD port No No No No No Yes (1 external clock/time Yes (1 external
input and output) clock/time
input and
output)
MAC address table 262143 262143 262143 262143 262143 262143 262143
size
Access ONTs 17408 17408 17408 17408 17408 4096 4096
Multicast users 17408 17408 17408 17408 17408 4096 4096
Static programs •4096 (earlier than 8192 8192 •4096 (earlier than 8192 8192 (V100R017C10 and 8192
V100R017C00) V100R017C00) later versions)
•8192 (V100R017C00 •8192 (V100R017C00
and later versions) and later versions)
Online programs V100R016C00: 4000 •IPv4: 8000 •IPv4: 8000 V100R016C00: 4000 •IPv4: 8000 V100R017C10 and later •IPv4: 8000
•V100R016C10:IPv4: •IPv6: 2000 •IPv6: 2000 •V100R016C10:IPv4: •IPv6: 2000 versions: •IPv6: 2000
4000 4000 •IPv4: 8000
•IPv6: 2000 •IPv6: 2000 •IPv6: 2000
V100R017C10 and later V100R017C10 and later
versions: versions:
•IPv4: 8000 •IPv4: 8000
•IPv6: 2000 •IPv6: 2000
Curso - Huawei MA560x Series – Operação e Configuração 18
Luiz Oliveira – CREA: 75436-D
18
9
Método de Manutenção / Gerência
19
Modem SCU
SCU
Cabo Serial RS-232 Linha CON
CON
ETH
Telefônica Cabo Serial ETH Gerência
PC RS-232 pela porta
PC PSTN CONSOLE
Linha (serial)
Porta Serial ou MA5600T Modem MA5600T
Telefônica
conversor USB/Serial
SCU SCU
CON LAN CON Gerência
LAN WAN ETH
ETH pela porta
Roteador ETHERNET
(LOCAL)
MA5600T MA5600T
PC PC PC PC
PC PC
SCU SCU
GE0/19/0 LAN GE0/19/0
CON CON Roteador
ETH ETH
GE0/19/1 GE0/19/1
Gerência
pela porta de
Internet
UPLINK
PC PC PC
MA5600T MA5600T PC
20
10
Manutenção Local Através da Porta Serial
Esta operação ajudará você à conectar-se à Esta operação ajudará você a conectar-
um computador (PC) em uma porta serial do se à um computador (PC) em uma porta
MA5600T. serial remota do MA5600T.
Modem SCU
SCU
Linha CON
Cabo Serial RS-232 CON Telefônica Cabo Serial ETH
ETH RS-232
PC
PSTN
PC
Linha
Porta Serial ou MA5600T Modem Telefônica MA5600T
conversor USB/Serial
21
H901MPLA / H902MPLA
H901MPLB
H901MPSC
H901MPSA
22
11
Manutenção Local Através da Porta Serial
H801MCUD /
H801MCUD1
Porta
gerencia Porta
Ethernet Console /
Serial
Curso - Huawei MA560x Series – Operação e Configuração 23
Luiz Oliveira – CREA: 75436-D
23
O Cabo Serial
24
12
Executar o software HyperTerminal
Inicie o HyperTerminal:
Start > Programs > Accessories > Communication > HyperTerminal.
Ou use outro programa qualquer para telnet.
Faça a seguinte configuração no programa.
9600 bit/s for baud rate
8 for data bits
None for parity
1 for stop bits
None for flow control
25
SCU PC
MA5600T CON
LAN WAN ETH
CON
ETH
Router
LAN
PC PC
SCU MA5600T
PC PC PC
26
13
Conteúdo
27
Nível do
Autoridade
Usuário
Similaridade:
• Executa todas as operações.
• Manutenção do MA5600T, contas de usuário e autoridade de
usuários.
Administrador e
Diferença:
Super usuário
• Somente um super usuário existe no sistema entretanto múltiplos
administradores podem existir.
• O super usuário tem o maior nível no sistema.
• O super usuário pode criar uma conta de administrador más um
administrador não tem autoridade para agregar um súper usuário.
28
14
Gerência de Usuários
29
Gerência de Usuários
30
15
Gerência de Usuários
Modificando um perfil criado por um usuário
31
Gerência de Usuários
Modificando o nível de um usuário
huawei(config)# terminal user level
Apagando um usuário
huawei(config)# undo terminal user name
32
16
Visualizar os operadores conectados
Command:
display client
------------------------------------------------------------------------------
ID Client name Domain name IP Address Login Time
------------------------------------------------------------------------------
1 root -- Serial 2000-01-01 11:21:19+08:00
3 talisson -- 192.168.100.2 2000-01-01 11:27:07+08:00
5 flavio -- 192.168.100.6 ssh 2000-01-01 11:28:17+08:00
8 junior -- 192.168.100.11 2000-01-01 11:29:58+08:00
9 alessandro -- 192.168.100.10 ssh 2000-01-01 11:31:19+08:00
11 emerson -- 192.168.100.7 ssh 2000-01-01 11:35:54+08:00
13 rafael02 -- 192.168.100.14 2000-01-01 11:39:00+08:00
15 luiz01 -- 192.168.100.12 2000-01-01 11:41:43+08:00
16 rafael01 -- 192.168.100.9 2000-01-01 11:45:18+08:00
------------------------------------------------------------------------------
Curso - Huawei MA560x Series – Operação e Configuração 33
Luiz Oliveira – CREA: 75436-D
33
34
17
Configurando Hora/Data/Timezone
35
Conteúdo
1. Utilizando a estrutura CLI
2. Configuração de Terminal de Manutenção
3. Gerência de Usuários
4. Gerência do Equipamento
36
18
NÃO EXECUTAR DURANTE O CURSO
MA5680T(config)# erase flash data ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
Options<E><active,standby>
Active board or standby board
37
38
19
Estado das Placas
Estado da
Descrição
Placa
Normal Indica que a placa está funcionando normalmente.
Failed indica que a placa está com falha.
Config indica que a placa está sendo configurada.
Indica que a placa esta conectada corretamente, más não está
Auto_find confirmada ainda.
Prohibited Indica que a placa está com o estado de proibido ou com bloqueio
39
40
20
Gerência do Equipamento
Frame-ID Description
Frame-ID
Frame-ID/slot-ID
41
Gerência do Equipamento
Frame-ID/slot-ID
MA5800-X2(config)# display board 0
{ <cr>||<K> }:
Command:
display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1 Online/Offline
-------------------------------------------------------------------------
0 H901PISB Normal
1 H901GPHF Normal
2
3 H901MPSC Active_normal CPCB
4 H901MPSC Standby_failed CPCB Offline
5
-------------------------------------------------------------------------
Curso - Huawei MA560x Series – Operação e Configuração 42
Luiz Oliveira – CREA: 75436-D
42
21
Gerência do Equipamento
43
Gerência do Equipamento
Criando as comunidades
huawei(config)# snmp-agent community read public01
huawei(config)# snmp-agent community write private01
44
22
Gerência do Equipamento
ou
MA5680T(config)# snmp-agent target-host trap-hostname “u2000” address 10.11.104.1 udp-
port 55555 trap-paramsname privado
Endereço IP do NMS (U2000
ou Zabbix PRTG, etc..)
Configurar Porta METH0 (interface de gerência local) ou VLAN como origem para envio dos traps.
huawei(config)# snmp-agent trap source meth 0
Outband : meth 0
OU Inband : vlanif <ID_VLAN>
45
Gerência do Equipamento
46
23
Manutenção Local Através da Porta Ethernet
Gerência Outband H801SCUB / H801SCUH
H801SCUK / H801SCUV
H801MCUD H802SCUB / H802SCUN
H801MCUD1
Porta
Ethernet
Gerência
OutBand
H901MPLA / H902MPLA
H901MPLB
H901MPSC
H901MPSA
47
Endereço IP do equipamento
Máscara
Adicionar uma rota.
huawei(config)# ip route-static 172.16.xx.0 24 172.16.4.1
48
24
Gerência Inband sobre LAN
GE0/19/0
CON
ETH
LAN
PC PC PC
SCU MA5600T
Internet
Router
PC
CON GE0/19/0
ETH
SCU MA5600T
Curso - Huawei MA560x Series – Operação e Configuração 49
Luiz Oliveira – CREA: 75436-D
49
LAN
Internet
Router
PC
PC PC
50
25
Configuração de Gerência Inband
Gerência Inband: É quando o tráfego da gerência flui por uma porta de uplink, junto com os dados do
cliente, mas em VLANs diferentes.
● Criar uma VLAN (de gerência) e agregar uma porta de uplink à esta VLAN.
huawei(config)# vlan 2000 smart
51
As VLANs
MA5680T(config)# vlan 1000 ?
---------------------------------------------
Command of config Mode:
---------------------------------------------
<cr> Please press ENTER to execute command
to VLAN range
vlantype<E><mux,standard,smart,super>
VLAN type
MA5680T(config)# vlan 1000 smart
vlan attrib vlanid [ to end-vlanid ] { q-in-q | stacking | common } undo vlan attrib vlanid [ to end-vlanid [ q-in-q | stacking ] ]
vlan attrib vlan-list { q-in-q | stacking | common } undo vlan attrib name vlan-name
vlan attrib name vlan-name { q-in-q | stacking | common } undo vlan attrib vlan-list [ q-in-q | stacking ]
vlan attrib bydesc description { q-in-q | stacking } undo vlan attrib bydesc description
Type ONU Port C-VLAN GEM DBA TCONT Traffic table S-VLAN OLT port
52
26
Visualizando VLANs
MA5680T(config)# display vlan all
{ <cr>|vlanattr<K>|vlantype<E><mux,standard,smart,super> }:
Command:
display vlan all
-----------------------------------------------------------------------
VLAN Type Attribute STND-Port NUM SERV-Port NUM VLAN-Con NUM
-----------------------------------------------------------------------
1 smart common 8 0 -
1000 smart common 1 1 -
-----------------------------------------------------------------------
Total: 2
Note : STND-Port--standard port, SERV-Port--service virtual port,
VLAN-Con--vlan-connect
53
Salvando as Configurações
MA5600T(config)# save
{ <cr>|configuration<K>|data<K> }: Comando
Command:
save
MA5600T(config)#
It will take several minutes to save configuration file, please wait...
MA5600T(config)#
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
MA5600T(config)#
The data is being saved, please wait a moment...
MA5600T(config)#
1[2015-08-19 11:52:13]:The percentage of saved data on 10 slot's main control board
is: 21%
MA5600T(config)#
1[2015-08-19 11:52:31]:The percentage of saved data on 10 slot's main control board
is: 98% Esperar por esta resposta.
MA5600T(config)#
1[2015-08-19 11:52:33]:The data of 10 slot's main control board is saved completely
Curso - Huawei MA560x Series – Operação e Configuração 54
Luiz Oliveira – CREA: 75436-D
54
27
Visualizando as Placas do Chassis
MA5680T(config)# display board 0
-------------------------------------------------------------------------
SlotID BoardName Status SubType0 SubType1 Online/Offline
-------------------------------------------------------------------------
0
1
2
3
4
5
6
7 H802SCUN Standby_normal
8 H802SCUN Active_normal
9 H805GPFD Normal
10
11
12
13
14
15
16
17 H801GICF Normal
18 H801GICF Normal
19
20
-------------------------------------------------------------------------
55
------------------------------------------------------------------------------
Power Status Power-off cause Power-off Time
------------------------------------------------------------------------------
POWER-ON - -
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Port Port Optic Native MDI Speed Duplex Flow- Active Link
Type Status VLAN (Mbps) Ctrl State
------------------------------------------------------------------------------
0 GE absence 1 - auto auto off active offline
1 GE absence 1 - auto auto off active offline
2 GE absence 1 - auto auto off active offline
3 GE absence 1 - auto auto off active offline
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Port Detecting Time(Min) TX State Auto-sensing
------------------------------------------------------------------------------
0 - - -
1 - - -
2 - - -
3 - - -
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Port 15Min 15Min 24Hour 24Hour
AlmProf WarnProf AlmProf WarnProf
------------------------------------------------------------------------------
0 - - - -
1 - - - -
2 - - - -
3 - - - -
------------------------------------------------------------------------------
Note: For any port, setting MDI to auto-negotiation is invalid, For a 1000 M
Electrical port in the full-duplex mode, setting MDI to any value is
invalid
Curso - Huawei MA560x Series – Operação e Configuração 56
Luiz Oliveira – CREA: 75436-D
56
28
Visualizando a Placa Controladora - Standby
---------------------------------------
Board Name : H802SCUN
Board Status : Standby normal
---------------------------------------
------------------------------------------------------------------------------
Power Status Power-off cause Power-off Time
------------------------------------------------------------------------------
POWER-ON - -
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Port Port Optic Native MDI Speed Duplex Flow- Active Link
Type Status VLAN (Mbps) Ctrl State
------------------------------------------------------------------------------
0 - - - - - - - - offline
1 - - - - - - - - offline
2 - - - - - - - - offline
3 - - - - - - - - offline
------------------------------------------------------------------------------
Note: For any port, setting MDI to auto-negotiation is invalid, For a 1000 M
Electrical port in the full-duplex mode, setting MDI to any value is
invalid
57
---------------------------------------
Board Name : H801GICF
Board Status : Normal
---------------------------------------
------------------------------------------------------------------------------
Power Status Power-off cause Power-off Time
------------------------------------------------------------------------------
POWER-ON - -
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Port Port Optic Native MDI Speed Duplex Flow- Active Link
Type Status VLAN (Mbps) Ctrl State
------------------------------------------------------------------------------
0 GE normal 1 - auto auto off active offline
1 GE absence 1 - auto auto off active offline
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Port Detecting Time(Min) TX State Auto-sensing
------------------------------------------------------------------------------
0 - - -
1 - - -
------------------------------------------------------------------------------
------------------------------------------------------------------------------
Port 15Min 15Min 24Hour 24Hour
AlmProf WarnProf AlmProf WarnProf
------------------------------------------------------------------------------
0 - - - -
1 - - - -
------------------------------------------------------------------------------
Note: For any port, setting MDI to auto-negotiation is invalid, For a 1000 M
Electrical port in the full-duplex mode, setting MDI to any value is
invalid
58
29
Visualizando GBIC na Porta de Uplink
Command:
display port ddm-info 0
Temperature(C) : 32.421876
Supply voltage(V) : 3.273800
TX bias current(mA) : 6.042000
TX power(dBm) : -2.797579
RX power(dBm) : -40.000000
59
Command:
display port state 1
--------------------------------------------------------
Port Information
--------------------------------------------------------
F/S/P 0/1/1
Port state Offline
Last down cause -
Last up time -
Last down time -
Port energy-saving flag No
xPON MAC chipset state Normal
Signal detect Normal
Available bandwidth(Kbps) 1237063
Illegal rogue ONT Inexistent
--------------------------------------------------------
Optical Module State
60
30
Visualizando a Placa de Serviço GPON
MA5680T(config)# display board 0/9
---------------------------------------
Board Name : H805GPFD
Board Status : Normal
---------------------------------------
-----------------------------------------------------------------------------
----------------------------------------------------------- F/S/P ONT SN Control Run Config Match Protect
Power Status Power-off cause Power-off Time ID flag state state state side
----------------------------------------------------------- -----------------------------------------------------------------------------
POWER-ON - - 0/ 9/0 1 4857544355F90A74 active offline initial initial no
----------------------------------------------------------- -----------------------------------------------------------------------------
----------------------------------------------------------- F/S/P ONT-ID Description
Port Port min-distance max-distance Optical-module -----------------------------------------------------------------------------
type (km) (km) status 0/ 9/0 1 TESTE
----------------------------------------------------------- -----------------------------------------------------------------------------
0 GPON 0 20 Online In port 0/ 9/0 , the total of ONTs are: 1, online: 0
1 GPON 0 20 Online In port 0/ 9/1 , the total of ONTs are: 0, online: 0
2 GPON 0 20 Online In port 0/ 9/2 , the total of ONTs are: 0, online: 0
3 GPON 0 20 Online In port 0/ 9/3 , the total of ONTs are: 0, online: 0
4 GPON 0 20 Online In port 0/ 9/4 , the total of ONTs are: 0, online: 0
5 GPON 0 20 Online In port 0/ 9/5 , the total of ONTs are: 0, online: 0
6 GPON 0 20 Online In port 0/ 9/6 , the total of ONTs are: 0, online: 0
7 GPON 0 20 Online In port 0/ 9/7 , the total of ONTs are: 0, online: 0
8 GPON 0 20 Online In port 0/ 9/8 , the total of ONTs are: 0, online: 0
9 GPON 0 20 Online In port 0/ 9/9 , the total of ONTs are: 0, online: 0
10 GPON 0 20 Online In port 0/ 9/10, the total of ONTs are: 0, online: 0
11 GPON 0 20 Online In port 0/ 9/11, the total of ONTs are: 0, online: 0
12 GPON 0 20 Online In port 0/ 9/12, the total of ONTs are: 0, online: 0
13 GPON 0 20 Online In port 0/ 9/13, the total of ONTs are: 0, online: 0
14 GPON 0 20 Online In port 0/ 9/14, the total of ONTs are: 0, online: 0
15 GPON 0 20 Online In port 0/ 9/15, the total of ONTs are: 0, online: 0
--------------------------------------------------------
61
{ catv-port<K>|eth-port<K>|pots-port<K>|tdm-port<K> }: eth-port
{ all<K>|ont-portid<U><1,255> }: all
Command:
display ont port state 1 0 eth-port all
huawei(config-if-gpon-0/5)#
------------------------------------------------------------------------
ONT-ID ONT ONT Speed(Mbps) Duplex LinkState RingStatus MA5680T(config)# display ont autofind
port-ID Port-type { all<K>|conflict-check<K>|time<K> }:all
------------------------------------------------------------------------
0 1 FE 100 full up - Command:
0 2 FE - - down loop display ont autofind all
0 3 FE - - down noloop ------------------------------------------------------
0 4 FE - - down - Number : 1
------------------------------------------------------------------------- F/S/P : 0/9/0
total: 4 current display: 4 Ont SN : 48575443C23A176A (HWTC-C23A176A)
huawei(config-if-gpon-0/5)# display ont port state Password : 0x00000000000000000000
{ portid<U><0,7> }:1 Loid :
{ ontid<U><0,63> }:0 Checkcode :
{ catv-port<K>|eth-port<K>|pots-port<K>|tdm-port<K> }:eth-port VendorID : HWTC
{ all<K>|ont-portid<U><1,255> }:1 Ont Version : 6A5.A
Ont SoftwareVersion : V3R015C10S106
Command: Ont EquipmentID : 310M
display ont port state 1 0 eth-port 1 Ont autofind time : 2018-02-07 02:28:33+08:00
------------------------------------------------------
huawei(config-if-gpon-0/5)# The number of GPON autofind ONT is 1
------------------------------------------------------------------------
ONT-ID ONT ONT Speed(Mbps) Duplex LinkState RingStatus
port-ID Port-type
------------------------------------------------------------------------
0 1 FE 100 full up -
------------------------------------------------------------------------
62
31
Visualizando Características das ONTs 2/2
huawei(config-if-gpon-0/5)# display ont port state 1 0 catv-port 1
{ <cr>||<K>|><K>|>><K> }:
MA5680T(config)# display ont ?
Command: ---------------------------------------------
display ont port state 1 0 catv-port 1
Command of privilege Mode:
huawei(config-if-gpon-0/5)# ---------------------------------------------
---------------------------------------------------- auto-load ONT automatic loading policy
ONT-ID ONT ONT LinkState TxPower autofind Automatically found ONT
port-ID port-type (dBmV) capability ONT capability
---------------------------------------------------- ftp-server-profile FTP server profile
0 1 CATV down 15.000 global-config Global configuration information
---------------------------------------------------- home-gateway-profile ONT home gateway profile
info ONT information
load ONT load
port ONT port management
power-shedding-profile
ONT power shedding profile
statistics <Group> statistics command group
tdm-vcl ONT TDM VCL
tr069-server-profile TR069 server profile
huawei(config-if-gpon-0/5)# display ont port state version ONT version information
{ portid<U><0,7> }: 1 wan-info The information about WAN ports
{ ontid<U><0,63> }: 0
{ catv-port<K>|eth-port<K>|pots-port<K>|tdm-port<K> }: pots-port
{ all<K>|ont-portid<U><1,255> }: 1
Command:
display ont port state 1 0 pots-port 1
huawei(config-if-gpon-0/5)#
---------------------------------------------------------------------------
Port Physical Admin Hook Session Service Call Service
ID State State State Type State State Codec
---------------------------------------------------------------------------
1 Normal Unlock OffHook Fax InService InCall T38
---------------------------------------------------------------------------
63
64
32
Visualizando uma ONTs Específica
MA5680T(config-if-gpon-0/9)# display ont info 0 1 ----------------------------------------------------------------
----------------------------------------------- Notes: * indicates Discrete TCONT(TCONT Unbound)
F/S/P : 0/9/0 ----------------------------------------------------------------
ONT-ID : 1 <T-CONT 0> DBA Profile-ID:1
Control flag : active <T-CONT 4> DBA Profile-ID:100
Run state : offline <Gem Index 100>
Config state : initial ---------------------------------------------------------------
Match state : initial |Serv-Type:ETH |Encrypt:off |Cascade:off |GEM-CAR:- |
DBA type : - |Upstream-priority-queue:0 |Downstream-priority-queue:- |
ONT distance(m) : - ---------------------------------------------------------------
ONT battery state : - Mapping VLAN Priority Port Port Bundle Flow Transparent
Memory occupation : - index type ID ID CAR
CPU occupation : - ----------------------------------------------------------------
Temperature : - 0 1000 - - - - - -
Authentic type : SN-auth ----------------------------------------------------------------
SN : 4857544355F90A74 (HWTC-55F90A74)
Management mode : OMCI
Software work mode : normal
Isolation state : normal -----------------------------------------------------------------
Description : TESTE Notes: Run the display traffic table ip command to query
Last down cause : - traffic table configuration
Last up time : - -----------------------------------------------------------------
Last down time : - Service profile ID : 100
Last dying gasp time : - Service profile name : FULL
ONT online duration : - -----------------------------------------------------------------
Type C support : - Port-type Port-number
Interoperability-mode : Unknown -----------------------------------------------------------------
----------------------------------------------- POTS adaptive
ETH adaptive
VoIP configure method : Default VDSL 0
------------------------------------------------- TDM 0
Line profile ID : 100 MOCA 0
Line profile name : FULL CATV 0
-------------------------------------------------
FEC upstream switch :Disable
OMCC encrypt switch :Off
Qos mode :PQ
Mapping mode :VLAN
TR069 management :Disable
TR069 IP index :0
65
66
33
MA5680T(config)# display file
{ <cr>|filename<S><Length 1-64> }:
Visualizando Arquivos
Command:
display file
flash:
FLASH VFS total size: 253952(K)
FLASH VFS idle size: 5751(K)
flash:
-----------------------------------------------------------------------------
File Name Size(B) Creation Time Attribute
-----------------------------------------------------------------------------
program.efs 28886278 2008-01-01 08:00:00+08:00 -rw
program_bak.efs 28886278 2008-01-01 08:00:00+08:00 -rw
voipfpga.efs 409738 2008-01-01 08:00:00+08:00 -rw
ver_match.efs
router_mode.efs
37638 2008-01-01 08:00:00+08:00
3 2018-02-06 12:37:37+08:00
-rw
-rw
• Configuração (.ini)
32_cpmu0107.efs 186118 2008-01-01 08:00:00+08:00 -rw
32_pmu02b03.efs 141446 2008-01-01 08:00:00+08:00 -rw
32_epmu0203.efs
32_h801esc.efs
57606 2008-01-01 08:00:00+08:00
18950 2008-01-01 08:00:00+08:00
-rw
-rw
• Database (.dat)
32_fan.efs 7942 2008-01-01 08:00:00+08:00 -rw
• Bios (.bin)
32_h801fcbc.efs 7814 2008-01-01 08:00:00+08:00 -rw
32_h801heud.efs 122374 2008-01-01 08:00:00+08:00 -rw
bios_h801biua.efs 12294 2008-01-01 08:00:00+08:00 -rw
io_h801biua.efs 41990 2008-01-01 08:00:00+08:00 -rw
• Program (.efs)
cpld_h801biua.efs 13958 2008-01-01 08:00:00+08:00 -rw
patch_load.efs 5803 2017-11-07 05:40:50+08:00 -rw
ZbTest 2395910 2008-01-01 08:00:00+08:00 -rw
cfm.efs 1412 2018-02-10 00:44:30+08:00 -rw
patch_load_bak.efs
lastword0.zip
lastword_managefile.bin
5803 2017-11-09 05:41:00+08:00
5958 2014-09-25 06:15:50+08:00
1020 2018-02-06 12:37:37+08:00
-rw
-rw
-rw
• Package (.bin)
blank_reserve.bin 133169152 2014-09-25 06:15:50+08:00 -rw
l2ss_maclearnextend.efs 4 2018-02-05 23:24:54+08:00 -rw
patchboardctrlblk_bak.pat 77 2017-11-09 05:41:05+08:00 -rw
patchboardctrlblk.pat 77 2015-12-27 04:05:55+08:00 -rw
brdxpon_snmp_cfg.efs 255 2015-12-27 04:08:55+08:00 -rw
lastword9.zip 6099 2017-10-17 04:03:04+08:00 -rw
boardtemplate.ini 2307 2018-02-10 00:44:38+08:00 -rw
lastword12.zip 7111 2017-10-25 05:01:09+08:00 -rw
frametemplate.ini 1168 2018-02-10 00:44:48+08:00 -rw
rsa_host_key.efs 1260 2017-11-07 05:36:41+08:00 -rw
topmemfilemngt 128 2018-02-06 12:37:37+08:00 -rw
sram_xpon_optic_exempt_lis 5132 2017-11-08 01:59:58+08:00 -rw
rsa_server_key.efs 540 2017-11-07 05:36:41+08:00 -rw
log_oper00.dat 99455 2017-11-07 05:37:06+08:00 -rw
data.dat 341586 2018-02-10 00:44:56+08:00 -rw
data_bak.dat 341586 2018-02-10 00:45:04+08:00 -rw
-----------------------------------------------------------------------------
Curso - Huawei MA560x Series – Operação e Configuração 67
Luiz Oliveira – CREA: 75436-D
67
Backup e Restore
68
34
Backup Configuration
69
Backup Configuration
Esse comando é usado para fazer backup do arquivo de configuração em um servidor especificado.
O arquivo de configuração contém dados configurados pelos usuários no dispositivo.
Para fazer o backup do arquivo de configuração do arquivo do sistema na memória flash da placa de controle para um PC ou terminal da rede, execute este comando.
Então, quando o sistema apresentar falha, é possível restaurar os dados configurados (dos usuários) carregando o arquivo de configuração de backup.
O arquivo de configuração pode ser editado usando uma ferramenta de texto. Desta forma, as configurações do dispositivo podem ser modificadas em lotes.
Após o backup do arquivo de configuração, o operador pode ver o arquivo de backup no caminho definido para salvar o arquivo.
huawei# backup configuration
{ ftp<K>|sftp<K>|tftp<K>|xmodem<K> }: tftp Comando
{ ServerIpAddress<I><X.X.X.X> }: 10.10.10.10
{ filename<S><Length 1-128> }: config.txt
Command:
backup configuration tftp 10.10.10.10 config.txt
Please save configuration file before backup, or the configuration file that
is backed up may not be the latest. Are you sure to continue? (y/n)[n]:y
Load(backup,duplicate,...) begins, please wait and notice the rate of progress
Any operation such as reboot or switchover will cause failure and unpredictable result
Backing up files starts from the host to the maintenance terminal
PARAMETERS :FrameID: 0, SlotID: 9, Position: -1, Backup type: Configuration file, Backup Object: Active
control board
huawei#
Esperar por esta
huawei#
resposta
Backing up files is successful from the host to the maintenance terminal
PARAMETERS :FrameID: 0, SlotID: 9, Position: -1, Backup type: Configuration file, Backup Object: Active
control board Curso - Huawei MA560x Series – Operação e Configuração 70
Luiz Oliveira – CREA: 75436-D
70
35
Autosave
Para habilitar a função de “Autosave”
huawei# autosave time
{ time_value<T><hh:mm:ss>|value<E><on,off> }:on
Command:
autosave time on
System autosave time switch: on
Autosave time: 00:00:00
Autosave type: data
Command:
autosave time 12:20:30
System autosave time switch: on
Autosave time: 12:20:30
Autosave type: data
71
Autosave
Command:
autosave interval on
System autosave interval switch: on
Autosave interval: 1440 minutes
Autosave type: data
72
36
Autosave
Para definir o “auto-save interval” para 60 minutos após as modificações:
huawei# autosave interval
{ configuration<K>|time<U><10,10080>|value<E><on,off> }:configuration
{ time<U><2,1440> }:60
Command:
autosave interval configuration 60
System autosave modified configuration switch: on
Autosave interval: 60 minutes
Autosave type: data
Command:
autosave interval 120
System autosave interval switch: on
Autosave interval: 120 minutes
Autosave type: data
73
Autobackup
Command:
auto-backup period data interval 2 time 03:20
auto-backup period data enable
74
37
Load Configuration
1
huawei# load configuration
2
{ ftp<K>|sftp<K>|tftp<K>|xmodem<K> }: tftp
{ ServerIpAddress<I><X.X.X.X> }: 10.10.10.10 huawei# active configuration system
{ filename<S><Length 1-128> }: config.dat System will reboot after this command, continue?
{ Options<E><active,standby,all> }: active (y/n)[n]: y
Command:
load configuration tftp 10.10.10.10 config.txt active
The new configuration file will overwrite the old one
Are you sure to load new configuration file? (y/n)[n]: y
Load(backup,duplicate,...) begins, please wait and notice the rate of progress
Any operation such as reboot or switchover will cause failure and unpredictable result
The loading starts
PARAMETERS :FrameID: 0, SlotID: 9, Position: -1, Load type: Configuration file, Load Object: Active control
board
huawei#
huawei#
The loading is successful
PARAMETERS :FrameID: 0, SlotID: 9, Position: -1, Load type: Configuration file, Load Object: Active control
board
huawei#
Note: The configuration file in 0 frame 9 slot will take effect after being activated
•NOTICE: - When you run the load configuration command to load a configuration file, activate the file directly but do not run the save configuration or
the save command to save it. Otherwise, the imported configuration file is lost.
•The system is reset after you run the active configuration system command. During the reset, the system selects the system configuration file for activating the
system configuration.
•When activating a large configuration file, the reboot time is long. For example, if there are 12 K service-ports, 12 K descriptors of service-ports, and mac-address
max-mac-count in each service-port, the reboot time is about 1 hour.
Curso - Huawei MA560x Series – Operação e Configuração 75
Luiz Oliveira – CREA: 75436-D
75
Verificar - IO Drivers
76
38