Escolar Documentos
Profissional Documentos
Cultura Documentos
R: Acidificação é uma ténica de estimulação que tem como objetivo remover os danos e/ou
aumentar a permeabilidade em regiões localizadas a poucos metros ao redor do poço. Os fatores
que influenciam no comportamento das misturas ácidas são: temperatura, concentração, pressão,
reações secundárias, produtos gasosos, velocidade de fluxo e composição da rocha.
R: Nos processos de acidificação que utilizam ácidos, o objetivo é uma reação mais lenta e de fácil
inibição contra corrosão em alta temperatura (150 – 200 °C).
R: Visto que o ácido nunca será distribuído igualmente entre todas as partes da formação
danificada, a eficiência do tratamento com ácido depende da taxa de injeção de ácido assim como
o volume de ácido, portanto é preciso ter a taxa de concentração de ácido.
R: Durante a preparação de soluções de misturas ácidas podem ocorrer acidente se não forem
manuseados com cuidado, ou se os procedimentos adequados não forem seguidos. Por isso é
UNIVERSIDADE DO ESTADO DE SANTA CATARINA – UDESC
CENTRO DE EDUCAÇÃO SUPERIOR DA FOZ DO ITAJAÍ- CESFI
DEPARTAMENTO DE ENGENHARIA DO PETRÓLEO – EPET
DISCIPLINA: ENGENHARIA DE POÇO II
7) For the reaction between 25 wt% HCl solution and calcite, calculate the gravimetric and
volumetric dissolving power of the acid solution.
9) A 30-ft thick, 40-md sandstone pay zone at a depth of 9000 ft is to be acidized with an acid
solution having a specific gravity of 1.07 and a viscosity of 1,2 cp down a 2-in. ID coil tubing.
The formation fracture gradiente is 0.7 psi/ft. The wellbore radius is 0,328 ft. Assuming a
reservoir pressure of 4000 psia, drainage área radius of 1500 ft and skin factor of 8, calculate:
a) the maximum acid injection rate using safety margin 200 psi.
b) the maximum expected surface injection pressure at the maximum injection rate.
10) A 18 wt% HCl is needed to propagate wormholes 2 ft from a 0,328-ft radius wellbore in a
limestone formation (specific gravity 2.71) with a porosity of 0,12. The designed injection
rate is 0,12 bbl/min-ft, the diffusion coefficient is 10-9 m2/sec, and the density of the 18% HCl
is 1,08 g/cm3. In linear core floods, 1,2 pore volume is needed for wormhole breakthrough at
the end of the core. Calculate the acid volume requirement using (a) Daccord’s model and (b)
the volumetric model.
RESPOSTAS:
Questão 7:
25% 𝐻𝐻𝐻𝐻𝐻𝐻 𝑒𝑒 𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶𝐶
• Dissolução graviometrica
𝑉𝑉𝑚𝑚 ∙ 𝑀𝑀𝑤𝑤𝑚𝑚 1 ∙ 100
𝛽𝛽 = 𝐶𝐶𝑎𝑎 ∙ → 𝛽𝛽 = 0,25 ∙ = 0,342
𝑉𝑉𝑎𝑎 ∙ 𝑀𝑀𝑤𝑤𝑎𝑎 2 ∙ 36,5
• Dissolução Volumetrica
𝜌𝜌𝑎𝑎 1,200
𝑋𝑋 = 𝛽𝛽 ∙ → 𝑋𝑋 = 0,34 ∙ = 0,15
𝜌𝜌𝑚𝑚 2,72
Questão 8:
𝑉𝑉𝑚𝑚 = 𝜋𝜋 ∙ (𝑟𝑟𝑎𝑎2 − 𝑟𝑟𝑤𝑤2 ) ∙ (1 − 𝜑𝜑)𝐶𝐶𝑚𝑚
𝑉𝑉𝑝𝑝 = 𝜋𝜋 ∙ (𝑟𝑟𝑎𝑎2 − 𝑟𝑟𝑤𝑤2 ) ∙ 𝜑𝜑 → 𝑉𝑉𝑝𝑝 = 𝜋𝜋 ∙ (1,5282 − 0,3282 ) ∙ 0,15 = 1,05 𝑓𝑓𝑡𝑡 3 /𝑓𝑓𝑓𝑓
• Dissolução gravimétrica
• Dissolução Volumetrica
𝑉𝑉𝑚𝑚 0,535
𝑉𝑉𝑎𝑎 = + 𝑉𝑉𝑝𝑝 + 𝑉𝑉𝑚𝑚 → 𝑉𝑉𝑎𝑎 = + 1,05 + 0,535 = 7,48 𝑓𝑓𝑡𝑡 3 𝑜𝑜𝑜𝑜 55,86 𝑔𝑔𝑔𝑔𝑔𝑔 18𝑤𝑤𝑤𝑤 %𝐻𝐻𝐻𝐻𝐻𝐻
𝑋𝑋 0,0907
Questão 9:
𝑎𝑎) 𝐴𝐴 𝑡𝑡𝑡𝑡𝑡𝑡𝑡𝑡 𝑑𝑑𝑑𝑑 𝑖𝑖𝑖𝑖𝑖𝑖𝑖𝑖çã𝑜𝑜 𝑚𝑚á𝑥𝑥𝑥𝑥𝑥𝑥𝑎𝑎
𝑏𝑏) 𝑝𝑝𝑤𝑤𝑤𝑤 = 𝑝𝑝𝑏𝑏𝑏𝑏 − ∆𝑝𝑝𝑠𝑠𝑠𝑠 → 𝑝𝑝𝑤𝑤𝑤𝑤 = 0,7 ∙ 9000 − 200 = 6100 𝑝𝑝𝑝𝑝𝑝𝑝
Questão 10:
𝑉𝑉𝑚𝑚 ∙ 𝑀𝑀𝑤𝑤𝑚𝑚 1 ∙ 100
𝛽𝛽 = 𝐶𝐶𝑎𝑎 ∙ → 𝛽𝛽 = 0,18 ∙ = 0,25 𝑙𝑙𝑙𝑙𝑙𝑙 𝐶𝐶𝐶𝐶𝐶𝐶𝑂𝑂3
𝑉𝑉𝑎𝑎 ∙ 𝑀𝑀𝑤𝑤𝑎𝑎 2 ∙ 36,5
𝜑𝜑 ∙ 𝛽𝛽 ∙ 𝛾𝛾𝑎𝑎 0,12 ∙ 0,25 ∙ 1,09
𝑁𝑁𝐴𝐴𝐴𝐴 = → 𝑁𝑁𝐴𝐴𝐴𝐴 = = 0,0137
(1 − 𝜑𝜑) ∙ 𝛾𝛾𝑚𝑚 (1 − 0,12) ∙ 2,71
𝑏𝑏𝑏𝑏𝑏𝑏 𝑚𝑚3
𝑞𝑞ℎ = 0,12 − 𝑓𝑓𝑓𝑓 → 𝑞𝑞ℎ = 1,04 × 10−9
𝑚𝑚𝑚𝑚𝑚𝑚 𝑠𝑠𝑠𝑠𝑐𝑐 − 𝑚𝑚
2 1
𝑑𝑑𝑑𝑑
𝜋𝜋 ∙ 𝜑𝜑 ∙ 𝐷𝐷 3 ∙ (𝑞𝑞ℎ )3 ∙ 𝑟𝑟𝑤𝑤ℎ
𝑉𝑉ℎ =
𝑏𝑏 ∙ 𝑁𝑁𝐴𝐴𝐴𝐴
2 1
𝜋𝜋 ∙ 0,12 ∙ (1 × 10−9 )3 ∙ (1,04 × 10−3 )3 ∙ 0,70961,6
𝑉𝑉ℎ = = 𝟎𝟎, 𝟏𝟏𝟏𝟏𝟏𝟏 𝒎𝒎𝟑𝟑 /𝒎𝒎
(1,2 × 10−5 ) ∙ 0,0137