Escolar Documentos
Profissional Documentos
Cultura Documentos
com
Opções de desenho
● Topologia - A topologia Flyback é suportada. Este valor não pode ser alterado.
● Tipo de otimização - Se a família de dispositivos lhe permitir escolher um tipo de
optimização, clique no ícone da calculadora para seleccionar entre optimização de
custos ou eficiência.
● Família - A alteração da opção família não está disponível para um desenho criado.
É necessário criar um novo desenho se quiser selecionar outra família.
● Pacote - Pode alterar esta opção para um desenho criado.
● Tensão de ruptura - Drenagem do dispositivo para a tensão de ruptura da fonte.
● Frequência - Dependendo da família do dispositivo, pode escolher o valor da
frequência de comutação a partir da lista.
● Limite de corrente - Para a família de dispositivos TinySwitch, clique no ícone da
calculadora para escolher entre Aumentado, Padrão e Reduzido no menu suspenso.
Escolha Increased (Aumentado) para que o dispositivo forneça a maior potência,
Reduced (Reduzido) para reduzir as perdas por condução no computador, e
Standard (Padrão) para um compromisso entre os modos de limite de corrente
reduzido e aumentado.
● Função M-pin - Este parâmetro está disponível para pacotes P/G das famílias
TopSwitch-HX e TopSwitch-GX onde existe M-pin. Selecionar ILIM/PLIM Only ou
UV/OV Only para ligar a programação de limitação de corrente e sobretensão.
● Feedback - Ao criar um novo design, PI Expert selecciona um tipo de feedback com
base na família de produtos PI Expert especificada. Para os dispositivos com
bobinagem de polarização opcional, é possível ligar a bobinagem de polarização
selecionando a caixa de verificação Utilizar polarização. Para os dispositivos com
bobinagem tendenciosa necessária, a caixa de verificação Use Bias está cinzenta. A
utilização de uma bobinagem tendenciosa quando é opcional reduz tipicamente a
quantidade de potência sem carga que o desenho irá consumir.
● Feedback - PI Expert selecciona um tipo de feedback com base na família de
produtos PI especificada. Alguns tipos de feedback requerem uma bobinagem
tendenciosa.
● Tipo de feedback
Para LinkSwitch-CV o tipo de feedback da família está definido para Feedback Winding e a
utilização de enviesamento é opcional. Ver Wizard - Opções de desenho para mais
informações.
Para os dispositivos com enrolamento de viés opcional, pode ligar o enrolamento de viés
selecionando a caixa de verificação Utilizar viés. Para os dispositivos com bobinagem de
polarização necessária, a caixa de verificação Utilizar polarização é cinzenta. A utilização de
uma bobinagem tendenciosa quando é opcional reduz tipicamente a quantidade de potência
sem carga que o desenho irá consumir.
Design Options
Use the Design Options form to view or change power supply specifications. The following
options are available:
● Optimization Type - If the device family allows you to choose an optimization type,
click the calculator icon to select between cost or efficiency optimization.
● Family - Changing the family option is not available for a created design. You need
to create a new design if you want to select another family.
● Frequency - Depending on the device family you can choose the switching frequency
value from the list.
● Current Limit - For the TinySwitch device family, click the calculator icon to choose
between Increased, Standard and Reduced in the drop down menu. Choose
Increased for the device to deliver the most power, Reduced for reduced conduction
losses in the switch, and Standard for a compromise between the reduced and
increased current limit modes.
● M-pin function - This parameter is available for P/G packages of TopSwitch-HX and
TopSwitch-GX families where M-pin exists. Select ILIM/PLIM Only or UV/OV Only to
turn on current limiting and overvoltage programming.
● Feedback – When creating a new design, PI Expert selects a feedback type based
on the specified PI Expert product family. For the devices with optional bias winding,
you can turn the bias winding on by selecting the Use Bias check box. For the
devices with required bias winding, the Use Bias check box is grayed out. Using a
bias winding when it is optional typically reduces the amount of no-load power the
design will consume.
Feedback Type
You can select the feedback type in the Feedback Type list. Use the Feedback Components
form to view and edit the feedback components. The number of available feedback schemes
depends on the PI Device family used. The most common feedback types are Secondary
Zener or Secondary TL431. For low cost designs there is also Primary Resistor or Primary
Zener feedback. If either Primary Resistor or Primary Zener is selected as the feedback
type, the Feedback Components form is unavailable for the design.
Bias Winding feedback is only available for the LinkSwitch-XT product family. Bias winding
feedback is very inexpensive and simple with regulation of about +/-10%. You cannot modify
any bias parameters when Bias Winding feedback type is selected. See the Feedback
Components form for more information.
Note: When the Feedback Type is either a secondary Zener or a TL431, PI Expert chooses
an Ultra Fast diode as the diode type for the bias diode.
Licenciado para - ABIMAEL JOSÉ VILLARROEL GONZÁLEZ - 70658972227 - Protegido por Eduzz.com
For LinkSwitch-CV family feedback type is set to Feedback Winding and using bias is
optional. See Wizard - Design Options for more information.
Indirect CC feedback consists of using the bias winding voltage to extract information about
the output. Any variations of the output are sensed by the bias winding and the controller will
make the necessary corrections based on this measurement.
Direct Secondary feedback can only be used in non-isolated designs, and basically it
consists of converting the output current into a voltage by means of a sense resistor. The
signal may or may not be filtered by a low pass filter, and is then connected to the feedback
pin.
The Fedback Type options available for InnoSwitch3-CP are summarized in the table below.
To note is the fact that InnoSwitch3-Pro does not need an external feedback network as it is
included in the secondary controller circuitry.
For the devices with optional bias winding, you can turn the bias winding on by selecting the
Use Bias check box. For the devices with required bias winding, the Use Bias check box is
grayed out. Using a bias winding when it is optional typically reduces the amount of no-load
power the design will consume.