Escolar Documentos
Profissional Documentos
Cultura Documentos
Transmissor
programável 2 fios
No. 5333V111-BR
De número de serial:
132094001 - 132094630
141115001
Revision Notes
The following list provides notes concerning revisions of this document.
1414
TRANSMISSOR PROGRAMÁVEL
2 FIOS
PRetop 5333
Conteúdo
Aplicação..................................................................................................... 2
Características técnicas........................................................................ 2
Montagem / instalação.......................................................................... 2
Aplicações................................................................................................... 3
Ordem: 5333.............................................................................................. 4
Especificações elétricas........................................................................ 4
Conexões..................................................................................................... 7
Diagrama de bloco................................................................................... 8
Programação.............................................................................................. 9
Especificações mecânicas.................................................................... 10
Montagem dos fios do sensor............................................................ 10
Appendix..................................................................................................... 11
ATEX Installation Drawing - 5333A............................................. 12
ATEX Installation Drawing - 5333D............................................. 13
IECEx Installation Drawing - 5333A............................................. 15
IECEx Installation Drawing - 5333D............................................. 16
FM Installation Drawing - 5333D.................................................. 18
CSA Installation Drawing - 5333D................................................ 20
INMETRO Instruções de Segurança - 5333A............................ 21
INMETRO Instruções de Segurança - 5333D............................ 22
5 333V1 1 1 - BR 1
TRANSMISSOR PROGRAMÁVEL 2 FIOS
PRetop 5333
Aplicação
• Medição de temperatura linearizada com Pt100...Pt1000 ou sensor Ni100...
Ni1000.
2 5333V1 1 1 - BR
Aplicações
Instalação de 2 fios
na sala de controle
RTD à 4...20 mA
+
- V+
mA
Instalação de 2 fios
na sala de controle
Resistência à 4...20 mA
V+
+
-
mA
5 333V1 1 1 - BR 3
Ordem: 5333
Tipo Versão
5333 Padrão :A
CSA, FM, ATEX, IECEx & INMETRO :D
Especificações elétricas
Especificações de range:
-40°C a +85°C
Especificações comuns:
Tensão de alimentação, DC
Padrão....................................................................... 8...35 V
CSA, FM, ATEX, IECEx & INMETRO.......... 8...30 V
Consumo interno....................................................... 25 mW...0.8 W
Queda de tensão....................................................... 8 VDC
Tempo de aquecimento.......................................... 5 min.
Interface de comunicações................................... Loop Link
Sinal / ruído................................................................. min. 60 dB
Tempo de resposta (programável)..................... 0.33...60 s
Dinâmicas de sinal, entrada.................................. 19 bit
Dinâmicas de sinal, saída....................................... 16 bit
Temperatura de calibração.................................... 20...28°C
Precisão, a melhor para valores gerais e básicos:
Valores Gerais
Tipo de Precisão Coeficiente de
entrada absoluta temperatura
Todas ≤ ±0.1% de span ≤ ±0.01% de span / °C
Valores básicos
Precisão Coeficiente de
Tipo de entrada básica temperatura
RTD ≤ ±0.3°C ≤ ±0.01°C/°C
Lin. R ≤ ±0.2 Ω ≤ ±20 mW / °C
4 5333V1 1 1 - BR
Efeito de variação da tensão
de alimentação.......................................................... ≤ 0,005% de span / VDC
Vibração........................................................................ IEC 60068-2-6 Teste FC
2...25 Hz................................................................... ±1,6 mm
25...100 Hz....................................................... ±4 g
Tamanho máximo do fio........................................ 1 x 1.5 mm2 fio flexível
Umidade....................................................................... < 95% RH (não-cond.)
Dimensões................................................................... Ø 44 x 20.2 mm
Grau de proteção (enclausurado / terminal).. IP68 / IP00
Peso................................................................................ 50 g
5 333V1 1 1 - BR 5
Aprovações:
EMC 2004/108/EC................................................... EN 61326-1
GOST R
Aprovação marinha:
Det Norske Veritas, Ships & Offshore.............. Stand. f. Certific. No. 2.4
Ex / S.I.:
ATEX 94/9/EC
5331A....................................................................... KEMA 10ATEX0003 X
5331D...................................................................... KEMA 03ATEX1535 X
Certificado FM............................................................ 2D5A7
Certificado CSA.......................................................... 1125003
IECEx.............................................................................. DEK 13.0036 X
INMETRO...................................................................... DEKRA 13.0002 X
GOST Ex
6 5333V1 1 1 - BR
Conexões
Entrada:
Resistência, Resistência,
RTD, 2-linhas RTD, 3-linhas 2-linhas 3-linhas
3 4 6 3 4 6 3 4 6 3 4 6
Saída:
Instalação de 2 fios
1 2
+ mA -
5 333V1 1 1 - BR 7
8
Alimentação +
1 8...35 VDC
DC
4 mA
Entrada + 6 DC
RTD Comm.
C PU
Resistência M UX PGA A /D
linear Comp. + 4
3
Entrada - D /A
5333V1 1 1 - BR
Circuito Ex, apenas 5333D
0...16
mA
E E PRO M
Alimentação -
Diagrama de bloco
2 mA
4...20 mA
5333
Programação
• Loop Link é uma interface de comunicações que é necessário para programar o
PRetop 5333.
• Loop Link não é aprovado para comunicação com módulos instalados em áreas
perigosas (Ex).
Equipamento
receptor
Desconectado
1 +VAlimentação
Vermelho * Amarelo
2 Entrada
Negro * Verde
PRetop 5333
Conector
08:30:00
Language O ption
O utput C om m unication
File Product Input PRetop 5331
2004-8-10
Date:
Serial no: 043201594
Tag no: PRelectronics
Analog output
Analog input O utput type: 4 - 20mA
Pt100 DIN/IEC
Input type: Sensor error: Upscale
0.00 - 50.00 C
Input range:
3-wire
C onnection:
L oop
p: ------
C old junction com
1.00 sec
Response time:
5909 - USB
L ink
5 333V1 1 1 - BR 9
Especificações mecânicas Montagem dos fios do sensor
+ -
+ -
ø 6 mm
33 mm 20.2 m m
ø 44 mm
Fios devem ser montados entre as chapas
de metal.
10 5333V1 1 1 - BR
Appendix
ATEX Installation Drawing - 5333A
5 333V1 1 1 - BR 11
5333QA02
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
For type of protection Ex nA, the transmitter shall be mounted in a metal enclosure providing a
degree of protection of at least IP54 according to EN60529.
For use in the presence of combustible dusts the transmitter shall be mounted in an enclosure
providing a degree of protection of at least IP6X in accordance with EN60529, the surface
temperature of the outer enclosure is 20 K above the ambient temperature
For an ambient temperature ≥ 60ºC, heat resistant cables shall be used with a rating of at least
20 K above the ambient temperature.
12 5333V1 1 1 - BR
5333QA01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Marking
II 1 G Ex ia IIC T4...T6 Ga
II 1 D Ex ia IIIC Da
II 1 M Ex ia I Ma
Hazardous area
Zone 0, 1, 2, 20, 21, 22 Non Hazardous Area
Terminal: 3,4,6 6
Uo: 27 VDC
Io: 7 mA 5 1+
Po: 45 mW
Lo: 35 mH 4 2 -
Co: 90 nF
3
5333D
Barrier
Terminal: 1,2
Ui: 30 VDC
Ii: 120 mA
Pi: 0.84 W
Li: 10μH
Ci: 1.0nF
5 333V1 1 1 - BR 13
5333QA01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Installation notes:
For installation in a potentially explosive dust atmosphere, the following instructions apply:
The transmitter shall be mounted in a metal enclosure form B that is providing a degree of
protection of at least IP6X according to EN60529, that is suitable for the application and
correctly installed.
Cable entries and blanking elements shall be used that are suitable for the application and
correctly installed.
For an ambient temperature ≥ 60ºC, heat resistant cables shall be used with a rating of at least
20 K above the ambient temperature.
The surface temperature of the enclosure is equal to the ambient temperature plus 20 K, for a
dust layer with a thickness up to 5 mm
14 5333V1 1 1 - BR
5333QI02
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Standards IEC 60079-0 : 2011, IEC 60079-11 : 2011, IEC 60079-15 : 2010
Terminal Ex nA [ic] Ex ic
1,2 Umax = 35V Ui : 35V, Ii:110mA, Ii:10µH, Ci:1,0nF
3,4,6 Uo: 5V, Io: 4mA, Po: 20mW, Lo: 900mH, Co: 1000µF
Installation note:
For installation in a potentialy explosive gas atmosphere, the following instructions apply:
For nA installation the transmitter must be installed in an metal enclosure e.g. a form B
enclosure, providing a degree of protection of at least IP54 according to IEC60529 or in an
enclosure with type of protection Ex n or Ex e.
Cable entry devices and blanking elements shall fulfill the same requirements
For an ambient temperature ≥ 60ºC, heat resistant cables shall be used with a rating of at
least 20 K above the ambient temperature.
For installation in a potentially explosive dust atmposphere, the following instructions apply:
The surface temperature of the enclosure is equal to the ambient temperature plus 20 K, for a
dust layer with a thickness up to 5 mm.
The transmitter must be mounted in a enclosure according to DIN 43729 that provides a
degree of protection of at least IP6X according to IEC60529, and that is suitable for the
application. Cable entry devices and blanking elements shall fulfill the same requirements.
5 333V1 1 1 - BR 15
5333QI01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Hazardous area
Zone 0, 1, 2, 20, 21, 22, M1 Non Hazardous Area
6
Terminal: 3,4,6
Uo: 30 VDC 5 1+
Io: 8 mA
Po: 60 mW 4 2 -
Lo: 35 mH 5333D
Co: 66 nF 3
5343B
Barrier
Terminal: 1,2
Ui: 30 VDC
Ii: 120 mA
Pi: 0.84 W
Li: 10μH
Ci: 1.0nF
16 5333V1 1 1 - BR
5333QI01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Installation notes.
In a potentially explosive gas atmosphere, the transmitter shall be mounted in a metal form B
enclosure in order to provide a degree of protection of at least IP20 according to IEC60529. If
however the environment requires a higher degree of protection, this shall be taken into
account.
For installation in a potentially explosive dust atmosphere, the following instructions apply:
For explosive dust atmospheres, the surface temperature of the outer enclosure is 20 K above
the ambient temperature.
The transmitter shall be mounted in a metal enclosure form B according to DIN43729 that is
providing a degree of protection of at least IP6X according to IEC60529, that is suitable for the
application and correctly installed.
Cable entries and blanking elements shall be used that are suitable for the application and
correctly installed.
For an ambient temperature ≥ 60ºC, heat resistant cables shall be used with a rating of at least
20 K above the ambient temperature.
5 333V1 1 1 - BR 17
5335QE01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Hazardous (Classified) Location Non Hazardous Location
Class I,Division1, Groups, A,B,C,D
Class I, Zone 0, IIC Associated Apparatus
or Barrier
+ with
Ambient temperature limits
T4: ‐40 to + 85 deg. Celcius
entity Parameters:
T6: ‐40 to + 60 deg. Celcius
UM < 250V
‐ Voc or Uo < Vmax or Ui
Terminal 1 , 2 Isc or Io < Imax or Ii
Vmax or Ui: 30 V Po < Pi
Imax or Ii: 120 mA Ca or Co > Ci + Ccable
Pmax or Pi: 0.84 W 1 2 La or Lo > Li + Lcable
Ci: 1 nF
Li:10 uH
18 5333V1 1 1 - BR
5335QE01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Equipment that is FM-approved for intrinsic safety may be connected to barriers based on the ENTITY
CONCEPT. This concept permits interconnection of approved transmitters, meters and other devices in
combinations which have not been specifically examined by FM, provided that the agency's criteria are
met. The combination is then intrinsically safe, if the entity concept is acceptable to the authority having
jurisdiction over the installation.
The entity concept criteria are as follows:
The intrinsically safe devices, other than barriers, must not be a source of power.
The maximum voltage Ui(VMAX) and current Ii(IMAX), and maximum power Pi(Pmax), which the device can
receive and remain intrinsically safe, must be equal to or greater than the voltage (Uo or VOC or Vt) and
current (Io or ISC or It) and the power Po which can be delivered by the barrier.
The sum of the maximum unprotected capacitance (Ci) for each intrinsically device and the interconnect-
ing wiring must be less than the capacitance (Ca) which can be safely connected to the barrier.
The sum of the maximum unprotected inductance (Li) for each intrinsically device and the interconnecting
wiring must be less than the inductance (La) which can be safely connected to the barrier.
The entity parameters Uo,VOC or Vt and Io,ISC or It, and Ca and La for barriers are provided by the barrier
manufacturer.
Model 5331C, 5331D, 5333C, 5333D, 5335C, 5335D, 5336D, 5337D and
5343B
Hazardous (Classified) Location Non Hazardous Location
Class I,Division2, Groups, A,B,C,D
Class I, Zone 2, IIC Associated Apparatus
or Barrier
+
Ambient temperature limits
T4: ‐40 to + 85 deg. Celcius
T6: ‐40 to + 60 deg. Celcius
Terminal 1 , 2
Vmax : 35 V
Ci: 0 µ F 1 2
Li:10 uH
6 3 This device must not be connected
to any associated apparatus which
5 4
uses or generates more than 250
VRMS
SENSOR
5 333V1 1 1 - BR 19
5335QE01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Hazardous area
Non Hazardous Area
T4: -40 ≤ Ta ≤ 85ºC
T6: -40 ≤ Ta ≤ 60ºC
Barrier
CLASS 2258 04 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe Entity - For Hazardous
Locations
Class I, Division 1, Groups A, B, C and D
Ex ia IIC, Ga
CLASS 2258 84 - PROCESS CONTROL EQUIPMENT - Intrinsically Safe Entity - For Hazardous
Locations - Certified to US Standards
Class I, Division 1, Groups A, B, C and D
Class I, Zone 0, AEx ia IIC, Ga
Warning:
Substitution of components may impair intrinsic safety.
The transmitters must be installed in a suitable enclosure to meet installation codes stipulated in
the Canadian Electrical Code (CEC) or for US the National Electrical Code (NEC).
20 5333V1 1 1 - BR
5333QB02
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Padrões ABNT NBR IEC 60079-0 : 2008, ABNT NBR IEC 60079-11 : 2009,
IEC 60079-15 : 2010, ABNT NBR IEC 60079-26 : 2008
Terminal Ex nA [ic] Ex ic
1,2 Umax = 35V Ui : 35V, Ii:110mA, Ii:10µH, Ci:1,0nF
3,4,6 Uo: 5V, Io: 4mA, Po: 20mW, Lo: 900mH, Co: 1000µF
5 333V1 1 1 - BR 21
5333QB01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Padrões ABNT NBR IEC 60079-0 : 2008, ABNT NBR IEC 60079-11 : 2009,
IEC 60079-15 : 2010, ABNT NBR IEC 60079-26 : 2008
Áreas perigosas
Zona 0, 1, 2, 20, 21, 22, M1 Sem áreas perigosas
6
Terminal: 3,4,5,6
Uo: 30 VDC 5 1+
Io: 8 mA
Po: 60 mW 4 2 -
Lo: 35 mH 5333D
Co: 66 nF 3
5343B
Barrier
Terminal: 1,2
Ui: 30 VDC
Ii: 120 mA
Pi: 0,84 W
Li: 10 μH
Ci: 1,0 nF
22 5333V1 1 1 - BR
5333QB01
LERBAKKEN 10, 8410 RØNDE DENMARK. WWW.PRELECTRONICS.COM
Notas de Instalação.
O transmissor deve ser montado em enclosure de metal forma B de acordo com DIN43729
que está fornecendo um grau de proteção de pelo menos IP6X de acordo com EN60529. Isso
é adequado para aplicação e corretamente instalado.
As entradas dos cabos e os elementos de obturação que podem ser utilizados são adequados
para a aplicação e corretamente instalados.
Para temperatura ambiente >= 60ºC, fios de resistência ao calor devem ser usados com uma
faixa de pelo menos 20K acima da temperatura ambiente.
5 333V1 1 1 - BR 23
Displays Displays programáveis com uma grande
variedade de entradas e saídas para visualização de temperatura,
volume, peso, etc. Linearização de fábrica, escala, e diferentes
funções de medição para programação via software PReset.
www.prelectronics.de
sales-de@prelectronics.com
www.prelectronics.es
sales-es@prelectronics.com
www.prelectronics.it
sales-it@prelectronics.com
www.prelectronics.se
sales-se@prelectronics.com
www.prelectronics.co.uk
sales-uk@prelectronics.com
www.prelectronics.com
sales-us@prelectronics.com
www.prelectronics.cn
sales-cn@prelectronics.com
Sede
Dinamarca www.prelectronics.com
PR electronics A/S sales-dk@prelectronics.com
Lerbakken 10 tel. +45 86 37 26 77
DK-8410 Rønde fax +45 86 37 30 85