Escolar Documentos
Profissional Documentos
Cultura Documentos
APOSTILA
INGLS
TCNICO
INGLS TCNICO
OBJETIVO: Fornecer ao aluno o entendimento de termos tcnicos e expresses
idiomticas que facilitem a interpretao de textos em ingls.
Atividade I
Nesta unidade iremos discutir textos que mostram para ns a importncia da Lngua
Inglesa em nosso dia-dia.
PORTUGUESE
Population
(million)
% of
native
speakers
Native
speakers
Population
(million)
% of
native
speakers
Native
speakers
United
States
286
86
246
Brazil
173
100
173
United
Kingdom
59
97
57
Portugal
10
100
10
Canada
32
63
20
Angola
13.5
60
8.1
Australia
20
85
17
Moambique
18.6
20
3.7
New
Zealand
95
3.8
Ireland
95
3.8
COUNTRIES
TOTAL
405
347.6
COUNTRIES
215.1
194.8
Devido forte expanso do ingls atualmente, fica difcil determinar com preciso a
quantidade de falantes de ingls e sua distribuio geogrfica. Praticamente no mundo
inteiro se fala ingls, mas nos 6 pases acima fala-se predominantemente ingls como
primeira lngua. Os nmeros acima se referem a pessoas que falam ingls e portugus
como primeira lngua (L1). Se fossem considerados aqueles que possuem domnio
sobre o ingls, porm como segunda lngua (L2), a quantidade de anglfonos aumenta
substancialmente em relao a lusfonos. No Canad, a porcentagem de falantes de
ingls aumenta de 63% para 83% (26,5 milhes), se for considerada a populao
bilnge que fala ingls como L2.
A populao estimada de falantes de ingls como L2 significativa tambm nos
seguintes pases (em milhes): Nigria (43), ndia (37), Filipinas (36,4), Paquisto (16),
frica do Sul: (10), Camares (6,6), Malsia (6) e Nepal (6).
O nmero total de falantes de ingls no mundo, incluindo os pases acima e outros
menos expressivos, chega aproximadamente a 580 milhes. Conforme David Crystal,
estimativas mais radicais, incluindo falantes com nveis de menor percepo e fluncia,
sugerem a existncia atualmente de um total superior a um bilho.
Os dados acima so todos baseados em recenseamentos de 1995 e 2000, projetados
em 2002.
INTERPRETAO DE TEXTOS
Lngua fundamentalmente um fenmeno oral. , portanto indispensvel desenvolver
uma certa familiaridade com o idioma falado, e mais especificamente, com a sua
pronncia, antes de se procurar dominar o idioma escrito.
The principle [speech before writing] applies even when the goal is only to read
(Lado, 1964, p. 50).
O portugus se caracteriza por uma certa flexibilidade com relao ao sujeito. Existem
as figuras gramaticais do sujeito oculto, indeterminado e inexistente, para justificar a
ausncia do sujeito. Mesmo quando no ausente, o sujeito freqentemente aparece
depois do verbo, e s vezes at no fim da frase (ex: Ontem apareceu um vendedor l
no escritrio).
O ingls mais rgido: praticamente no existem frases sem
sujeito e ele aparece sempre antes do verbo em frases afirmativas e negativas. O
sujeito sempre um nome prprio (ex: Paul is my friend), um pronome (ex: He's my
friend) ou um substantivo (ex: The house is big). Pode-se dizer que o pensamento em
ingls se estrutura a partir do sujeito; em seguida vm o verbo, o complemento, e os
adjuntos adverbiais. Para uma boa interpretao de textos em ingls, no adianta saber
o vocabulrio apenas; preciso compreender a estrutura, e para isso de fundamental
importncia a identificao do verbo e do sujeito.
A ordem normal em portugus substantivo adjetivo (ex: casa grande), enquanto que
em ingls o inverso (ex: big house). Alm disto, qualquer substantivo em ingls
potencialmente tambm um adjetivo, podendo ser usado como tal. (ex: brick house =
casa de tijolos; vocabulary comprehension test = teste de compreenso de
vocabulrio). Sempre que o aluno se defrontar com um aparente conjunto de
substantivos enfileirados, deve l-los de trs para diante intercalando a preposio "de"
no meio.
...ing
gerund
noun
adjective
go - ir
turn on - ligar
turn off - desligar
turn down - desprezar
turn into - transformar em
Atividade II
Contextual guessing
Nesta unidade voc aprender o significado de palavras desconhecidas, fazendo uso de um
elemento vital: o contexto.
O texto no-linear uma rica fonte de informaes: o aspecto visual, as ilustraes, o tipo de
letra usado, as aspas, os nmeros, etc., ajudam-nos a descobrir muita coisa sobre o contedo
de um texto. Muitas vezes, porm, quando uma palavra no est dentro de um texto, isto ,
quando est descontextualizada, sua decodificao torna-se difcil, pois o leque de
alternativas que se coloca diante de ns muito amplo. A eliminao da incerteza nesse caso
mais complicada.
Ao contrrio, quanto tal palavra tem um contexto uma sentena, uma situao essa
desvantagem reduzida. Assim, a palavra j no esta mais sozinha, ela mantm laoscom o
restante da setena ou da situao. esse meio circundante que d palavra um significado
especifico, dentre tantos outros que ela poderia ter.
Quando encontramos uma palavra desconhecida no texto, podemos tomar as seguintes
atitudes:
Perguntar do colega do lado
Perguntar ao professor
Consultar o dicionrio
Tentar seguir adiante mesmo sem saber a palavra
Levantar hipteses a respeito do possvel significado da palavra, usando o contexto
como guia.
O texto abaixo est em portugus, mas contm algumas palavras imaginrias. Leiao e procure descobrir o significado de tais palavras. Identifique tambm os
elementos que o/a ajudaram a chegar a essas concluses.
Xington
A primeira instituio estabelecida pela regio domestica foi o xington. Essa instituio parece
ser to antiga quanto raa indo-europia e quanto prpria religio domstica.
Mesmo nos tempos antigos, tanto o turron quanto a turre tomavam parte ativa no ritual do
xington.
Entre os romanos, a cerimnia do xington constitua-se de trs defrats: na primeira, a turre
deixada o lar pafist. Na segunda, os dois turri faziam oraes diante da nova talas e,
finalmente, prestavam, juntos, um kirps aos deuses.
Na idade antiga, a instituio do xington era indissolvel e o mitanes quase impossvel. O
direito romano, por exemplo, facilmente permitia dissolver-se xington quando celebrado por
usus, mas dificilmente o permitia quando por lei.
Atividade III
Considere o seguinte de emprego publicado por uma empresa americana numa revista
especializada em eletrnica em eletrnica.
PROJECT ENGINEER
Challenging
Career Opportunities
Battelle, one of the worlds leading not-to-profit research development and educational
organizations, has immediate and rewarding opportunities for you in the following areas:
Communications
Circuit design
Automatic control design
Micro processor and minicomputer system control
Electronic inspection
Engineering and systems development
Computer-aided manufacturing
Ingls Tcnico - Pgina 8
Atividade IV
Especificaes em Corrente Contnua
Os fabricantes de dispositivos semicondutores, por meio de manuais (data book), catlogos ou
Internet, fornecem diversas especificaes dos diodos para operao em circuitos CC (ou DC)
e CA (ou AC). Analisaremos apenas as especificaes CC dos diodos.
1. Complete o quadro abaixo:
Especificaes
IFAV (IFDC) (max)
VF (max)
Ir (max)
Vr (max)
Ingls
Forward current
Forward voltage
Reverse current
Reverse voltage
Portugus
Atividade V
O texto seguinte refere-se a uma instruo de manuseio de dispositivos
semicondutores extrado da publicao Components Techinical Descriptions and
Characteristics for Students da Siemens.
Soldering Instructions
Any semiconductor components is extraordinary sensitive to an exceeding of the maximum
permissible junction temperature. When designing the devices, care must be taken that the
Ingls Tcnico - Pgina 9
0.5
4
1.5
5
5
10
mm
s
1.5
5
2.5
6
5
13
mm
s
The lead length is measured from the soldered joint onwards, i.e. with normally clad plates
from plate bottom onward, and with through-plated holes from the plate top onwards.
Exerccios de Interpretao de texto.
1.
2.
3.
4.
Atividade VI
Traduza cada tpico (respectivos pargrafos) do texto abaixo:
First International Satellite Plans
The United States and Russia were the first two nations to draw plans for an artificial satellite.
In 1955, the United States and Russia publicly announced their proposals concerning the
construction of satellites. Within two years, Russia accomplished their goal, and the United
States followed closely behind.
Sputnik 1
Sputnik 1 was the first artificial satellite to bring the Space Age to life. On October 4, 1957, the
Soviet Union launched Sputnik 1. Its official Russian name was Iskustvennyi Sputnik Zemli, or
"Fellow Traveler of the Earth." Sputnik 1 was launched by Russia's Old Number Seven rocket
at Baikonur Cosmodrome. The once secret cosmodrome is what makes Russia lead the rest of
the world in launching men and machines into space month after month. Sputnik 1 was
described as "a silver-zinc battery and a radio transmitter in a 23 inch polished aluminum ball"
(Curtis 1). The satellite was also pressurized with nitrogen circulated by a cooling fan. Two
Atividade VII
O texto seguinte foi adaptado do Manual do Software Simulador de Circuitos
Electronics Workbench Verso 5, produzido pela Interactive Image Technologies.
Diode
Diodes allow current to flow in only one direction and can therefore be used as simple solidstate switches in AC circuits, being either open (not conducting) or closed (conducting).
Terminal A is called the anode and terminal K is called the cathode.
Exerccios de Interpretao de texto
1. Faa a verso para portugus do primeiro pargrafo do texto.
2. De acordo com o texto, como so denominados os terminais do diodo?
Atividade VIII
O texto seguinte foi adaptado do Manual do Software Simulador de Circuitos
Eletronics Workbench verso 5, produzido pela Interactive Image Techologies.
Full-wave bridge rectifier
This component uses four diodes to perform full-wave rectification of an input AC voltage. Two
diodes conduct during each half cycle, giving a full-wave rectified output voltage.
Ingls Tcnico - Pgina 11
Atividade IX
Todos os enunciados dos exerccios de circuitos eltricos que se encontram abaixo
esto em ingls. A partir dos seus conhecimentos em circuitos eltricos e o
entendimento do enunciado de cada questo d sua respectiva resposta.
1. Which is the statement of the law of Kirchhoff?
2. Which are the fundamental characteristics of the circuits in series and parallel?
3. Which is the mathematical equation of the law of Ohm?
c) The same alarm of the previous problem (12Vcc) when discharged it absorbs 2A of the
battery. Which is your resistance when discharged?
d) An automobile tape recorder consume 0,6A of the battery. Is what being known your
internal resistance in this condition of 10ohms to determine for the law of Ohm if the
automobile has battery of 6 V or 12 V?
Atividade X
O texto seguinte foi adaptado do Manual do Software Simulador de Circuitos Eletronics
Workbench verso 5, produzido pela Interactive Image Technologies.
Zener Diode
A zener diode is designed to operate in the reverse breakdown, or zener region.
In the forward region, it starts conducting around 0.7V, just like an ordinary silicon diode.
In the leakage region, between zero and breakdown, it has only a small reverse current. The
breakdown has a sharp knee, followed by an almost vertical increase in current.
Zener diodes are used primarily for regulation because they maintain constant output voltage.
Atividade XI
O texto seguinte uma adaptao de um fragmento do tpico Discrete LED selecting made
easier, extrado da publicao Catalog of Optoelectronic Products da General Instrument.
Electrical Considerations
Most incandescents are rated in terms of voltage; LEDs, on the other hand, are currentdependent devices since they are basically diodes.
When operating from constant-voltage sources, incorporating a current-limiting resistor with
each LED should provide protection.
Basic DC circuit. For the simple circuit shown in Figure 1 the resistor value can be calculated
from : RL = Vcc Vf / If.
Where Vf and If are taken from an LED Data Sheet. The power rating required for the resistor
should also be kept in mind.
Exercicios de Interpretao de Texto
1. De acordo com o primeiro pargrafo do texto, o que diferencia os LEDs da maioria dos
dispositivos incandescentes?
2. Faa a verso para o portugus do segundo pargrafo do texto.
Atividade XII
O texto seguinte uma adptao de um fragmento do tpico Discrete LED selecting made
easier, extrado da publicao Catalog of Optoelectronic Products da General
Instrument.
Electrical Considerations
AC Operation. LEDs should be operated in the forward direction only. Therefore, the LED
circuit must provide reverse-voltage protection if applied voltage is expected to exceed the Vr
maximum rating of the LED.
We have a circuit that having an ordinary silicon diode (e.g. 1N914) placed back-to-back with
the LED.
We are an alternate and more novel approach that utilizes two LEDs in parallel. If no current
flows, neither LED lights. But as long as current does flow (in either direction), one of the LEDs
lights and one does not (because one LED will be conducting and the other not conducting.)
Atividade XIII
O texto seguinte uma adptao do tpico sobre transistores extrado da publicao
Components Techinal Descriptions and Characteristics for Students da Siemens.
Transistors
General
Transistors are semiconductor components witch can be used for amplification, generation of
oscillations and for control and for control and switching purposes.
Basic Transistor Configurations
Transistors may be operated in three basic circuit configurations. This results in considerable
differences in the electrical characteristics. It is therefore necessary to indicate not only the
parameters but also the pertinent basic circuit configuration.
Atividade XIV
O texto seguinte uma adaptao de um fragmento do tpico Discrete LED selecting
made easier, extrado da publicao Catalog of Optoelectronic Products da General
Instrument.
Electrical Considerations
Active-Low Drive Circuit. Shows a single-transistor drive circuit that lights the LED when the
transistor is low, i.e., conducting. The value for RL can be calculated from RL = (Vcc Vf
Vce (sat)) / If
Active-High Drive Circuit. Shows a single-transistor drive circuit that lights the LED when
the transistor is high, i.e., not conducting. The value for RL can be calculated from RL
=(Vcc Vf) / If
For both equations, Vf, If and Vce (sat) are taken from a Semiconductors Devices Data
Sheet. The power rating required for the resistors should also be kept in mind.
Exerccios de Interpretao de Texto
1. Faa a verso para portugus do texto Active-Low Drive Circuit.
2. Por que na equao referente ao texto Active-High Drive Circuit no aparece o termo
Vce (sat)?
Atividade XV
O texto seguinte refere-se a um equipamento de laboratrio, de fabricante fictcio, tendo sido
adaptado a partir da anlise de alguns manuais de instruo.
Instruction Manual udio Signal Generator
Model OF 992 Arthur Systems
Description
The Arthur Audio Signal Generator Model 0F992 is a frequency generator with low
distorcion output and large frequency response, that covers the frequencies from 1 Hz to 100
Atividade XVI
O texto seguinte foi adaptado do Manual do Software Simulador de Circuitos Eletronics
Workbench Verso 5 , produzido pela Interactive Image Technologies.
NPN & PNP Bipolar Junction Transistors (BJT)
A Bipolar junction transistor, or BJT, is a current-based valve used for controlling electronic
current. BTJs are commonly used in amplification and switching applications. They come in
two versions: NPN and PNP. The letters refer to the polarities, positive or negative, of the
materials that make up the transistor sandwich. For both NPNs and PNPs, the terminal with the
arrowhead represents the emitter.
An NPN transistor has two n-regions (collector and emiter) separated by a p-regions (collector
and emmiter) separated by an n-region (base).
Characteristcs Equations
IE = IC + IB
DC = IC/IB = hfe
where
DC = hFE = DC current gain
AC = hfe = small-signal current gain
Ic = collector current
Ib = base current
Ie = emmiter current
The model for the PNP transistor is the same as the NPN model, except the polarities of the
terminals currents and voltages are reversed.
Exerccios de Interpretao de Texto
1. De acordo com o texto, qual o material semicondutor correspondente a cada terminal
em cada verso do transistor?
2. De acordo com o texto, como representado o terminal emissor nas duas verses do
transistor?
3. De acordo com o texto, qual a diferena entre DC e AC?
4. Faa a verso para o portugus do ultimo pargrafo do texto.
Atividade XVII
Os textos informativos seguintes foram extrados do catlogo americano Radio Snack
Americas Techonolohgy Store.
Headphone I
Realistic LV 10. Electroacoustical design and 2 dynamic elements for clear, clean sound.
Foam earcushions. 20 20,000 Hz. 10 ft, coiled cord, plug.
Headphone II
Realistic New 45. Efficient rareerth magnets deliver deep, solid bass. Ideal for portable
CD players. Weigh just 3.3 ounces. 20 20,000 Hz. Light, flexible, 6 -ft, cord, 1/8 plug.
With 1/8 to adpter.
Atividade XVIII
Os textos informativos seguintes foram extrados do catlogo americano Radio Snack
Americas Technology Store.
Atividade XIX
A seguir, apresentaremos dois exemplos de amplificadores integrados com suas
especificaes. Estas so retiradas de manuais do fabricante.
Circuito integrado TODA 1510AQ Philips
Especificao
Vs[V]
(min/typ/mx.)
Ptot[W]
(mx.)
Itot[mA]
(typ/mx.)
Isb[mA]
(mx.)
Zi[M] (min.)
Ingls
Supply
voltage
range
Total power
dissipation
Total current
Portugus
Min.
6,0
Tp.
14,4
Mx.
18,0
15
75
Stand-by
current
Input
impedance
120
2
Ingls
Supply
voltage
Power
output
Output
current
Input
resistence
Portugus
Min.
4,0
Tp.
Mx.
28,0
8
2,5
Atividade XX
O anncio de propaganda seguinte foi extrado da revista americana Electronics.
Atividade XXI
Abaixo encontramos alguns termos tcnicos em ingls. Vamos aprender o que significa
cada termo, tentando traduzi-los.
Amplitude Modulation (AM)
The baseband signal is caused to vary the amplitude or height of the carrier wave to create the
desired information content.
Amplifier
A device used to boost the strength of an electronic signal.
Analog
A form of transmitting information characterized by continuously variable quantities, as
opposed to digital transmission, which is characterized by discrete bits of information in
numerical steps. An analog signal is responsive to changes in light, sound, heat and pressure.
Analog-to-Digital Conversion (ADC)
Process of converting analog signals to a digital representation. DAC represents the reverse
translation.
Atividade XXII
As respectivas definies abaixo so referentes aos componentes encontrados no Kit
Didtico de Microondas. Traduza as especificaes de cada componente.
Techinical descriptions of components used in ED-3000
1. Gunn Oscillator: is connected to a 8~10 V DC power source. The power out put of the
Gunn oscillator ranges from 5 to 20 milliwatts, depending upon the supply voltage.
2. PIN-diode modulator: utilizes the property of a PIN diode which is placed across a
waveguide.
3. Frequency meter: The basic principle of frequency meter is to join the frequency to a
waveguide.
4. Variable attenuator: provides na attenuation by varying the degree of insertion of a matched
resistive strip into a waveguide.
5. Slotted line: is used to probe the amplitude and the phase of the standing wave pattern.
6. Reflecting sheet; a mean of reflecting electrmagnetic waves in free space when measuring
the wavelength of a signal.
7. Waveguide: used in measurements of the wavelength and the phase velocity inside a
waveguide.
D o significado dos termos tcnicos abaixo:
Remote interfacecellphoneControlslotProcessphonecardSensorbuttonsReference outputpliersContorllerscrewFocusscrewdriverfloppy diskgeneratorkeyboardsocketmemoryplugcablepinmobile phoneelectrode-
Atividade XXIII
Exerccio de Interpretao de Texto
1. Leia o texto abaixo e responda as respectivas perguntas:
what you need in the telecommunication?
In the modern world, some companies are finding it more efficient to have certain employees
stay at home and do all of their work on their home computers. Then, using telecommunicatios,
they transmit their work over a modem into the office where it is printed and distributed.
Telecommunications are used now for hundreds of different applications. Investors routinely
check their stock market holdings, pilots file flight plans and get weather briefings, and
shoppers compare and purchase merchandise on their computers. national and international
electronic mail is sent and received with local phone calls, and electronic bulletin, boards are
used for everything from selling used cars to finding dates.
Telecommunicating is accomplished by linking your computer to telephone lines and contacting
someone through a device called modem.
a) Como podemos enxergar a Telecomunicaes nos dias de hoje?
b) De acordo com o texto quais as aplicaes diferentes nas Telecomunicaes?
c) Como feita a Telecommunicating?
2. Explique a definio de cada elemento relatado abaixo:
A modem
Modem transmission speeds are measured in baud, roughly equivalent to bits per
second(bps). Typical speeds are 9600, 14400 and 28800 baud.
E-mail
Eletronic mail requires some special software. You type a message onto your computer
screen, click a send button and it pops up on the recipient's screen - provide that he or she is
connected to your computer via a network like the Internet.
Fax-modem
Is a modem with software and hardware which can emulate a fax machine. this allows you to
receive a fax directly into your computer, where you can read it or your printer. To send a fax
you prepare the document on your computer- for example, by using a word processor.
A stand-alone fax service
Is a facsimile machine which transmits copies of original documents. It operates by scanning
pictorial or textual documents so that the image is converted into electrical signals which are
sent to and used by a receiving machine that produces a copy of the original.
Teletext on ITV and Channel Four
Is an information service in Britain which broadcsts a database alongside the TV signal. It
provides constantly updated and real time information.
Atividade XXIV
Significado de alguns termos tcnicos
D o significado dos termos tcnicos abaixo:
Full-wave bridge retifierCommunicationFrequencyCircuitAutomatic controlMicro processorComponentsSemiconductorsDiodeVoltageConductInputOutputDC terminalsElectricityPower stationsElectricity generatorsEquipamentAlternatorValveRotorElectric current700 watt outputlightstelevisionAC voltageNot conductingSoldering-
Atividade XXV
Encontramos abaixo alguns termos encontrados na rea de telecomunicaes.
AMPS - Advanced Mobile Phone System. Abreviatura do sistema celular analgico adotado no
Brasil. Nesse sistema de telefonia mvel, a rea de cobertura dividida em clulas para
permitir o maior nmero de ligaes simultneas.