Escolar Documentos
Profissional Documentos
Cultura Documentos
Report
Project
Customer:
Project Name: Project_Chupaca
Location: Peru, CUZCO
Date: 2022-10-21
Designer
Name:
Phone:
Email:
Address:
Software
Version: 2.0.0.71
DB version: 20221017-204042
Table of Abbreviations
Abbreviation Description
Add. Ref. Additional Refrigerant
AM Airflow Mode
Block Load Block Load
CM Cooling Operation Mode
Corr. Capa Correction Capacity
Corr. PI Correction Power Input
CR Combination Ratio
DB Dry Bulb Temperature
Des Temp Design Temperature
Dis. Temp. Discharge Temperature
Equip. Name Equipment Name
EWT Entering Water Temperature
FR Flow Rate
HM Heating Operation Mode
IDU Indoor Unit
LWT Leaving Water Temperature
Max. Capa Maximum Capacity
Min. HOR Minimum Heating Operation Ratio
ODU Outdoor Unit
Op. WF Range Operating Water Flow Range
Op. WT Range Operating Water Temperature Range
Operating Temp. Range Operating Temperature Range
PHE Plate Heat Exchanger
Pipe Mat. Piping Material
PL Pressure Loss
PWL Sound Power level
Ref. Pipe Refrigerant Pipe
Rq. Vent. Vol. Required Ventilation Volume
SHC Sensible Heat Capacity
SPL Sound Pressure Level
TC Total Capacity
WB Wet Bulb Temperature
47/43, 120 DB / WB, LWT (for DVM Chiller Heating capacity)
DVM Pro 2.0
Equipment List
Type Model Code Qty. Description
UMA-1.01-C 1
UMA-1.01-H 1
UMA-1.02-C 1
UMA-1.02-H 1
UMA-1.03-C 1
UMA-1.03-H 1
UMA-2.01-C 1
UMA-2.01-H 1
UMA-2.02-C 1
UMA-2.02-H 1
UMA-2.03-C 1
UMA-2.03-H 1
UMA-2.04-C 1
UMA-2.04-H 1
UMA-3.01-C 1
IDU
UMA-3.01-H 1
UMA-3.02-C 1
UMA-3.02-H 1
UMA-3.03-C 1
UMA-3.03-H 1
UMA-3.04-C 1
UMA-3.04-H 1
UMA-3.05-C 1
UMA-3.05-H 1
UMA-3.06-C 1
UMA-3.06-H 1
UMA-3.07-C 1
UMA-3.07-H 1
UMA-3.08-C 1
UMA-3.08-H 1
DVM Pro 2.0
UMA-3.09-C 1
UMA-3.09-H 1
UMA-4.01-C 1
UMA-4.01-H 1
UMA-4.02-C 1
UMA-4.02-H 1
UMA-4.03-C 1
UMA-4.03-H 1
UMA-4.04-C 1
IDU
UMA-4.04-H 1
UMA-4.05-C 1
UMA-4.05-H 1
UMA-5.01-C 1
UMA-5.01-H 1
UMA-5.02-C 1
UMA-5.02-H 1
UMA-5.03.H 1
UMA-5.03-C 1
MXJ-YA1509M 6 Y-joint
MXJ-YA2815M 1 Y-joint
UMA-1.01-C 1
IDU
UMA-1.01-H 1
UMA-1.02-C 1
IDU
UMA-1.02-H 1
UMA-1.03-C 1
IDU
UMA-1.03-H 1
UMA-2.01-C 1
IDU
UMA-2.01-H 1
UMA-2.02-C 1
IDU
UMA-2.02-H 1
UMA-2.03-C 1
IDU
UMA-2.03-H 1
UMA-2.04-C 1
IDU
UMA-2.04-H 1
UMA-3.01-C 1
IDU
UMA-3.01-H 1
UMA-3.02-C 1
IDU
UMA-3.02-H 1
UMA-3.03-C 1
IDU
UMA-3.03-H 1
UMA-3.04-C 1
IDU
UMA-3.04-H 1
UMA-3.05-C 1
IDU
UMA-3.05-H 1
UMA-3.06-C 1
IDU
UMA-3.06-H 1
UMA-3.07-C 1
IDU
UMA-3.07-H 1
UMA-3.08-C 1
IDU
UMA-3.08-H 1
UMA-3.09-C 1
IDU
UMA-3.09-H 1
UMA-4.01-C 1
IDU
UMA-4.01-H 1
UMA-4.02-C 1
IDU
UMA-4.02-H 1
UMA-4.03-C 1
IDU
UMA-4.03-H 1
UMA-4.04-C 1
IDU
UMA-4.04-H 1
UMA-4.05-C 1
IDU
UMA-4.05-H 1
UMA-5.01-C 1
IDU
UMA-5.01-H 1
UMA-5.02-C 1
IDU
UMA-5.02-H 1
UMA-5.03.H 1
IDU
UMA-5.03-C 1
Piping
System (UMA-1.01)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU60 UMA-1.01-C
IDU 1F
- IDU61 UMA-1.01-H
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU60 UMA-1.01-C - - - - - - - - -
IDU61 UMA-1.01-H - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-1.01 AM080JXVANH/TL - - - -
Combination Ratio
AM080JXVANH/TL 107.60 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 7.58
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-1.02)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU62 UMA-1.02-H
IDU 1F
- IDU63 UMA-1.02-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU62 UMA-1.02-H - - - - - - - - -
IDU63 UMA-1.02-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-1.02 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 122.71 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.22
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-1.03)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU55 UMA-1.03-H
IDU 1F
- IDU56 UMA-1.03-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU55 UMA-1.03-H - - - - - - - - -
IDU56 UMA-1.03-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-1.03 AM080JXVANH/TL - - - -
Combination Ratio
AM080JXVANH/TL 116.89 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 7.71
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-2.01)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU7 UMA-2.01-C
IDU 1F
- IDU10 UMA-2.01-H
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU7 UMA-2.01-C - - - - - - - - -
IDU10 UMA-2.01-H - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-2.01 AM080JXVANH/TL - - - -
Combination Ratio
AM080JXVANH/TL 115.99 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 7.69
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-2.02)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU65 UMA-2.02-C
IDU 1F
- IDU64 UMA-2.02-H
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU65 UMA-2.02-C - - - - - - - - -
IDU64 UMA-2.02-H - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-2.02 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 128.93 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.33
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-2.03)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU66 UMA-2.03-H
IDU 1F
- IDU67 UMA-2.03-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU66 UMA-2.03-H - - - - - - - - -
IDU67 UMA-2.03-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-2.03 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 110.41 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.20
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-2.04)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU91 UMA-2.04-H
IDU 1F
- IDU92 UMA-2.04-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU91 UMA-2.04-H - - - - - - - - -
IDU92 UMA-2.04-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-2.04 AM120JXVANH/TL - - - -
Combination Ratio
AM120JXVANH/TL 115.62 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 9.92
DVM Pro 2.0
Piping (Continued)
IDU
Pipe Mat
R
3000
MXJ-YA2512M
1/2''|1 1/8''(in) 3/8''|3/4''(in) 0 UMA-2.04-C | IDU92
3.00m|0EA 34104Btu/h | -Btu/h |34104Btu/h
3.00m|0EA
#
1/2''|1 1/8''(in)
0 UMA-2.04-H | IDU91
98455Btu/h | -Btu/h |98455Btu/h
3.00m|0EA
#
UMA-2.04
AM120JXVANH/TL
1F -Btu/h | -Btu/h
0
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.01)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU70 UMA-3.01-H
IDU 1F
- IDU71 UMA-3.01-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU70 UMA-3.01-H - - - - - - - - -
IDU71 UMA-3.01-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.01 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 116.39 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.11
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.02)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU72 UMA-3.02-H
IDU 1F
- IDU73 UMA-3.02-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU72 UMA-3.02-H - - - - - - - - -
IDU73 UMA-3.02-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.02 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 127.93 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.31
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.03)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU93 UMA-3.03-H
IDU 1F
- IDU94 UMA-3.03-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU93 UMA-3.03-H - - - - - - - - -
IDU94 UMA-3.03-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.03 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 128.26 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.52
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.04)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU101 UMA-3.04-H
IDU 1F
- IDU102 UMA-3.04-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU101 UMA-3.04-H - - - - - - - - -
IDU102 UMA-3.04-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.04 AM050KXMDCH/AZ - - - -
Combination Ratio
AM050KXMDCH/AZ 127.12 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 40.00 m). 40.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 50.00 m) (ODU higher
50.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 40.00 m) (ODU lower
40.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 4.18
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.05)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU103 UMA-3.05-H
IDU 1F
- IDU104 UMA-3.05-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU103 UMA-3.05-H - - - - - - - - -
IDU104 UMA-3.05-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.05 AM050KXMDCH/AZ - - - -
Combination Ratio
AM050KXMDCH/AZ 118.51 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 40.00 m). 40.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 50.00 m) (ODU higher
50.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 40.00 m) (ODU lower
40.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 4.10
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.06)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU105 UMA-3.06-H
IDU 1F
- IDU106 UMA-3.06-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU105 UMA-3.06-H - - - - - - - - -
IDU106 UMA-3.06-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.06 AM050KXMDCH/AZ - - - -
Combination Ratio
AM050KXMDCH/AZ 118.52 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 40.00 m). 40.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 50.00 m) (ODU higher
50.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 40.00 m) (ODU lower
40.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 4.10
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.07)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU107 UMA-3.07-H
IDU 1F
- IDU108 UMA-3.07-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU107 UMA-3.07-H - - - - - - - - -
IDU108 UMA-3.07-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.07 AM040KXMDCH/AZ - - - -
Combination Ratio
AM040KXMDCH/AZ 123.44 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 40.00 m). 40.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 30.00 m) (ODU higher
30.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 25.00 m) (ODU lower
25.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
15.00 m 0.00 m
(restriction: 15.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 3.50
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.08)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU76 UMA-3.08-H
IDU 1F
- IDU77 UMA-3.08-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU76 UMA-3.08-H - - - - - - - - -
IDU77 UMA-3.08-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.08 AM080JXVANH/TL - - - -
Combination Ratio
AM080JXVANH/TL 106.11 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 7.56
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-3.09)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU109 UMA-3.09-H
IDU 1F
- IDU110 UMA-3.09-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU109 UMA-3.09-H - - - - - - - - -
IDU110 UMA-3.09-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-3.09 AM050KXMDCH/AZ - - - -
Combination Ratio
AM050KXMDCH/AZ 120.18 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 40.00 m). 40.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 50.00 m) (ODU higher
50.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 40.00 m) (ODU lower
40.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 4.12
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-4.01)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU143 UMA-4.01-H
IDU 1F
- IDU136 UMA-4.01-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU143 UMA-4.01-H - - - - - - - - -
IDU136 UMA-4.01-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-4.01 AM050KXMDCH/AZ - - - -
Combination Ratio
AM050KXMDCH/AZ 120.58 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 40.00 m). 40.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 50.00 m) (ODU higher
50.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 40.00 m) (ODU lower
40.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 4.12
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-4.02)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU78 UMA-4.02-H
IDU 1F
- IDU79 UMA-4.02-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU78 UMA-4.02-H - - - - - - - - -
IDU79 UMA-4.02-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-4.02 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 129.09 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.34
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-4.03)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU80 UMA-4.03-H
IDU 1F
- IDU81 UMA-4.03-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU80 UMA-4.03-H - - - - - - - - -
IDU81 UMA-4.03-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-4.03 AM120JXVANH/TL - - - -
Combination Ratio
AM120JXVANH/TL 120.99 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 10.03
DVM Pro 2.0
Piping (Continued)
IDU
Pipe Mat
R
3000
MXJ-YA2512M
1/2''|1 1/8''(in) 3/8''|3/4''(in) 0 UMA-4.03-C | IDU81
3.00m|0EA 51697Btu/h | -Btu/h |51697Btu/h
3.00m|0EA
#
1/2''|1 1/8''(in)
0 UMA-4.03-H | IDU80
87014Btu/h | -Btu/h |87014Btu/h
3.00m|0EA
#
UMA-4.03
AM120JXVANH/TL
1F -Btu/h | -Btu/h
0
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-4.04)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU82 UMA-4.04-H
IDU 1F
- IDU83 UMA-4.04-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU82 UMA-4.04-H - - - - - - - - -
IDU83 UMA-4.04-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-4.04 AM080JXVANH/TL - - - -
Combination Ratio
AM080JXVANH/TL 115.62 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 7.69
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-4.05)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU144 UMA-4.05-H
IDU 1F
- IDU142 UMA-4.05-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU144 UMA-4.05-H - - - - - - - - -
IDU142 UMA-4.05-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-4.05 AM180JXVANH/TL - - - -
Combination Ratio
AM180JXVANH/TL 117.38 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 13.44
DVM Pro 2.0
Piping (Continued)
IDU
Pipe Mat
R
3000
MXJ-YA2815M
5/8''|1 1/8''(in) 3/8''|5/8''(in) 0 UMA-4.05-C | IDU142
3.00m|0EA 3.00m|0EA 27559Btu/h | -Btu/h |27559Btu/h
#
5/8''|1 1/8''(in)
0 UMA-4.05-H | IDU144
3.00m|0EA
174300Btu/h | -Btu/h |174300Btu/h
#
UMA-4.05
AM180JXVANH/TL
1F -Btu/h | -Btu/h
0
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-5.01)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU85 UMA-5.01-H
IDU 1F
- IDU86 UMA-5.01-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU85 UMA-5.01-H - - - - - - - - -
IDU86 UMA-5.01-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-5.01 AM080JXVANH/TL - - - -
Combination Ratio
AM080JXVANH/TL 117.86 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 7.72
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-5.02)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU87 UMA-5.02-H
IDU 1F
- IDU88 UMA-5.02-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU87 UMA-5.02-H - - - - - - - - -
IDU88 UMA-5.02-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-5.02 AM100JXVANH/TL - - - -
Combination Ratio
AM100JXVANH/TL 124.43 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 8.25
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Piping (Continued)
System (UMA-5.03)
Design Condition
Outdoor Indoor
Design Condition (Air)
CM HM CM HM
Temperature (DB/WB) [°C] 22.2 / 12.7 0.9 / -2.3 27.0 / 19.0 20.0 / 15.0
Installation
Type Floor Room Name Equip. Name Model Code
- IDU89 UMA-5.03.H
IDU 1F
- IDU90 UMA-5.03-C
Outdoor Unit
CM HM CM HM
Indoor Unit
Des Temp[°C] Max. Capa. [Btu/h] Corr. Capa. [Btu/h]
Equip.
Model Code AM CM HM CM HM CM HM
Name
WB DB TC SHC TC TC SHC TC
IDU89 UMA-5.03.H - - - - - - - - -
IDU90 UMA-5.03-C - - - - - - - - -
Accessory
Address
Equip. Name Model Code Accessory
Main RMC
UMA-5.03 AM120JXVANH/TL - - - -
Combination Ratio
AM120JXVANH/TL 117.91 HP - - - - -
DVM Pro 2.0
Piping (Continued)
Pipe length from first Y-Joint to the farthest IDU is 3.30 m (Restriction: 45.00 m). 45.00 m 3.30 m
Height difference between ODU and IDU is 0.00 m (restriction: 110.00 m) (ODU higher
110.00 m 0.00 m
than IDUs).
Height difference between ODU and IDU is 2.00 m (restriction: 110.00 m) (ODU lower
110.00 m 2.00 m
than IDUs).
Height difference between IDUs when there is no wall mounts with EEV is 0.00 m
50.00 m 0.00 m
(restriction: 50.00 m).
Refrigerant
Factory Charging and Additional Refrigerant Amount Refrigerant Amount [kg]
Total 9.96
DVM Pro 2.0
Piping (Continued)
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Controller
Controller Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-1.01)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-1.02)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-1.03)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-2.01)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-2.02)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-2.03)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-2.04)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.01)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.02)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.03)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.04)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.05)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.06)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.07)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.08)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-3.09)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-4.01)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-4.02)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-4.03)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-4.04)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-4.05)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-5.01)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-5.02)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Wiring
System (UMA-5.03)
Wiring Diagram
-The above system configuration may differ from The actual installation conditions.
Please refer to The installation manual for full details.
DVM Pro 2.0
Product Specification
UMA-1.01
Outdoor Unit
Model Name AM080JXVANH/TL
Module Single
Mode HP
HP 8
MCA A 18.00
Current
MFA A 25.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 3/4''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-1.01 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 57
Sound Pressure
Sound
Cooling dB(A) 77
Power Level
Net Weight kg 186.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-1.01 (Continued)
Indoor Unit
Model Code - UMA-1.01-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 24470
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 24470
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2151.00
Fan
External pressure Maximum Pa 498.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-1.01 (Continued)
Indoor Unit
Model Code - UMA-1.01-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 57774
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 57774
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2151.00
Fan
External pressure Maximum Pa 498.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-1.02
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-1.02 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-1.02 (Continued)
Indoor Unit
Model Code - UMA-1.02-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 74190
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 74190
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3530.00
Fan
External pressure Maximum Pa 424.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-1.02 (Continued)
Indoor Unit
Model Code - UMA-1.02-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 43050
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 43050
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3530.00
Fan
External pressure Maximum Pa 424.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-1.03
Outdoor Unit
Model Name AM080JXVANH/TL
Module Single
Mode HP
HP 8
MCA A 18.00
Current
MFA A 25.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 3/4''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-1.03 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 57
Sound Pressure
Sound
Cooling dB(A) 77
Power Level
Net Weight kg 186.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-1.03 (Continued)
Indoor Unit
Model Code - UMA-1.03-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 54803
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 54803
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2592.00
Fan
External pressure Maximum Pa 349.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-1.03 (Continued)
Indoor Unit
Model Code - UMA-1.03-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 34542
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 34542
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2592.00
Fan
External pressure Maximum Pa 349.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.01
Outdoor Unit
Model Name AM080JXVANH/TL
Module Single
Mode HP
HP 8
MCA A 18.00
Current
MFA A 25.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 3/4''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-2.01 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 57
Sound Pressure
Sound
Cooling dB(A) 77
Power Level
Net Weight kg 186.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-2.01 (Continued)
Indoor Unit
Model Code - UMA-2.01-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 34120
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 34120
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2513.00
Fan
External pressure Maximum Pa 374.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.01 (Continued)
Indoor Unit
Model Code - UMA-2.01-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 54537
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 54537
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2513.00
Fan
External pressure Maximum Pa 374.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.02
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-2.02 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-2.02 (Continued)
Indoor Unit
Model Code - UMA-2.02-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 49542
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 49542
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3195.00
Fan
External pressure Maximum Pa 523.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.02 (Continued)
Indoor Unit
Model Code - UMA-2.02-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 73642
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 73462
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3195.00
Fan
External pressure Maximum Pa 523.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.03
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-2.03 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-2.03 (Continued)
Indoor Unit
Model Code - UMA-2.03-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 85430
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 85430
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2281.00
Fan
External pressure Maximum Pa 398.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.03 (Continued)
Indoor Unit
Model Code - UMA-2.03-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 20055
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 20055
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2281.00
Fan
External pressure Maximum Pa 398.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.04
Outdoor Unit
Model Name AM120JXVANH/TL
Module Single
Mode HP
HP 12
MCA A 25.00
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 1/2''
Connections Type Welding
Gas Pipe
Diameter in 1 1/8''
Type R410A
Refrigerant
Factory Charging kg 6.50
DVM Pro 2.0
Product Specification
UMA-2.04 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 62
Sound Pressure
Sound
Cooling dB(A) 81
Power Level
Net Weight kg 210.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-2.04 (Continued)
Indoor Unit
Model Code - UMA-2.04-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 98455
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 98455
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3962.00
Fan
External pressure Maximum Pa 548.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-2.04 (Continued)
Indoor Unit
Model Code - UMA-2.04-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 34104
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 34104
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3962.00
Fan
External pressure Maximum Pa 548.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.01
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-3.01 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.01 (Continued)
Indoor Unit
Model Code - UMA-3.01-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 63403
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 63043
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3268.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.01 (Continued)
Indoor Unit
Model Code - UMA-3.01-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 47800
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 47800
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3268.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.02
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-3.02 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.02 (Continued)
Indoor Unit
Model Code - UMA-3.02-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 71329
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 71329
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2858.00
Fan
External pressure Maximum Pa 498.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.02 (Continued)
Indoor Unit
Model Code - UMA-3.02-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 50900
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 50900
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2858.00
Fan
External pressure Maximum Pa 498.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.03
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-3.03 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.03 (Continued)
Indoor Unit
Model Code - UMA-3.03-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 98540
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 98540
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2046.00
Fan
External pressure Maximum Pa 398.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.03 (Continued)
Indoor Unit
Model Code - UMA-3.03-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 24000
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 24000
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2046.00
Fan
External pressure Maximum Pa 398.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.04
Outdoor Unit
Model Name AM050KXMDCH/AZ
Mode HP
HP 5
MCA A 27.00
Current
MFA A 40.00
Compressor Quantity EA 1
Type Propeller
Output W 139
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 5/8''
Type R410A
Refrigerant
Factory Charging kg 2.50
DVM Pro 2.0
Product Specification
UMA-3.04 (Continued)
Outdoor Unit
Sound
Sound Cooling dB(A) 55
Pressure
Net Weight kg 83.50
W mm 940
W mm 1009
D mm 419
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -20.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.04 (Continued)
Indoor Unit
Model Code - UMA-3.04-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 30827
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 30827
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1974.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.04 (Continued)
Indoor Unit
Model Code - UMA-3.04-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 29900
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 29900
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1974.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.05
Outdoor Unit
Model Name AM050KXMDCH/AZ
Mode HP
HP 5
MCA A 27.00
Current
MFA A 40.00
Compressor Quantity EA 1
Type Propeller
Output W 139
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 5/8''
Type R410A
Refrigerant
Factory Charging kg 2.50
DVM Pro 2.0
Product Specification
UMA-3.05 (Continued)
Outdoor Unit
Sound
Sound Cooling dB(A) 55
Pressure
Net Weight kg 83.50
W mm 940
W mm 1009
D mm 419
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -20.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.05 (Continued)
Indoor Unit
Model Code - UMA-3.05-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 33114
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 33114
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1674.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.05 (Continued)
Indoor Unit
Model Code - UMA-3.05-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 23500
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 23500
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1674.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.06
Outdoor Unit
Model Name AM050KXMDCH/AZ
Mode HP
HP 5
MCA A 27.00
Current
MFA A 40.00
Compressor Quantity EA 1
Type Propeller
Output W 139
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 5/8''
Type R410A
Refrigerant
Factory Charging kg 2.50
DVM Pro 2.0
Product Specification
UMA-3.06 (Continued)
Outdoor Unit
Sound
Sound Cooling dB(A) 55
Pressure
Net Weight kg 83.50
W mm 940
W mm 1009
D mm 419
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -20.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.06 (Continued)
Indoor Unit
Model Code - UMA-3.06-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 43153
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 43153
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1319.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.06 (Continued)
Indoor Unit
Model Code - UMA-3.06-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 13465
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 13465
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1319.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.07
Outdoor Unit
Model Name AM040KXMDCH/AZ
Mode HP
HP 4
MCA A 24.00
Current
MFA A 32.00
Compressor Quantity EA 1
Type Propeller
Type BLDC
Output W 125
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 5/8''
Type R410A
Refrigerant
Factory Charging kg 2.00
Sound
Sound Cooling dB(A) 52
Pressure
DVM Pro 2.0
Product Specification
UMA-3.07 (Continued)
Outdoor Unit
Sound
Heating dB(A) 54
Sound Pressure
Sound
Cooling dB(A) 73
Power Level
Net Weight kg 79.00
W mm 940
W mm 1009
D mm 419
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -20.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.07 (Continued)
Indoor Unit
Model Code - UMA-3.07-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 37264
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 37264
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1266.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.07 (Continued)
Indoor Unit
Model Code - UMA-3.07-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 13700
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 13700
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1266.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.08
Outdoor Unit
Model Name AM080JXVANH/TL
Module Single
Mode HP
HP 8
MCA A 18.00
Current
MFA A 25.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 3/4''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-3.08 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 57
Sound Pressure
Sound
Cooling dB(A) 77
Power Level
Net Weight kg 186.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.08 (Continued)
Indoor Unit
Model Code - UMA-3.08-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 66140
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 66140
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1612.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.08 (Continued)
Indoor Unit
Model Code - UMA-3.08-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 14961
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 14961
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1612.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.09
Outdoor Unit
Model Name AM050KXMDCH/AZ
Mode HP
HP 5
MCA A 27.00
Current
MFA A 40.00
Compressor Quantity EA 1
Type Propeller
Output W 139
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 5/8''
Type R410A
Refrigerant
Factory Charging kg 2.50
DVM Pro 2.0
Product Specification
UMA-3.09 (Continued)
Outdoor Unit
Sound
Sound Cooling dB(A) 55
Pressure
Net Weight kg 83.50
W mm 940
W mm 1009
D mm 419
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -20.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-3.09 (Continued)
Indoor Unit
Model Code - UMA-3.09-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 44495
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 44495
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1289.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-3.09 (Continued)
Indoor Unit
Model Code - UMA-3.09-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 12913
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 12913
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 1289.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.01
Outdoor Unit
Model Name AM050KXMDCH/AZ
Mode HP
HP 5
MCA A 27.00
Current
MFA A 40.00
Compressor Quantity EA 1
Type Propeller
Output W 139
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 5/8''
Type R410A
Refrigerant
Factory Charging kg 2.50
DVM Pro 2.0
Product Specification
UMA-4.01 (Continued)
Outdoor Unit
Sound
Sound Cooling dB(A) 55
Pressure
Net Weight kg 83.50
W mm 940
W mm 1009
D mm 419
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -20.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-4.01 (Continued)
Indoor Unit
Model Code - UMA-4.01-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 50600
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 50600
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 737.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.01 (Continued)
Indoor Unit
Model Code - UMA-4.01-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 7000
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 7000
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 737.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.02
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-4.02 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-4.02 (Continued)
Indoor Unit
Model Code - UMA-4.02-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 78680
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 78680
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3273.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.02 (Continued)
Indoor Unit
Model Code - UMA-4.02-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 44656
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 44656
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3273.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.03
Outdoor Unit
Model Name AM120JXVANH/TL
Module Single
Mode HP
HP 12
MCA A 25.00
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 1/2''
Connections Type Welding
Gas Pipe
Diameter in 1 1/8''
Type R410A
Refrigerant
Factory Charging kg 6.50
DVM Pro 2.0
Product Specification
UMA-4.03 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 62
Sound Pressure
Sound
Cooling dB(A) 81
Power Level
Net Weight kg 210.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-4.03 (Continued)
Indoor Unit
Model Code - UMA-4.03-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 87014
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 87014
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3877.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.03 (Continued)
Indoor Unit
Model Code - UMA-4.03-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 51697
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 51697
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3877.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.04
Outdoor Unit
Model Name AM080JXVANH/TL
Module Single
Mode HP
HP 8
MCA A 18.00
Current
MFA A 25.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 3/4''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-4.04 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 57
Sound Pressure
Sound
Cooling dB(A) 77
Power Level
Net Weight kg 186.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-4.04 (Continued)
Indoor Unit
Model Code - UMA-4.04-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 66167
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 66167
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2494.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.04 (Continued)
Indoor Unit
Model Code - UMA-4.04-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 22200
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 22200
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2494.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.05
Outdoor Unit
Model Name AM180JXVANH/TL
Module Single
Mode HP
HP 18
MCA A 39.10
Current
MFA A 50.00
Type Propeller
Output W 620
Type Welding
Liquid Pipe
Piping Diameter in 5/8''
Connections Type Welding
Gas Pipe
Diameter in 1 1/8''
Type R410A
Refrigerant
Factory Charging kg 8.40
DVM Pro 2.0
Product Specification
UMA-4.05 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 64
Sound Pressure
Sound
Cooling dB(A) 86
Power Level
Net Weight kg 307.00
W mm 1295
W mm 1363
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-4.05 (Continued)
Indoor Unit
Model Code - UMA-4.05-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 174300
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 174300
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3062.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-4.05 (Continued)
Indoor Unit
Model Code - UMA-4.05-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 27559
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 27559
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3062.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-5.01
Outdoor Unit
Model Name AM080JXVANH/TL
Module Single
Mode HP
HP 8
MCA A 18.00
Current
MFA A 25.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 3/4''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-5.01 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 57
Sound Pressure
Sound
Cooling dB(A) 77
Power Level
Net Weight kg 186.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-5.01 (Continued)
Indoor Unit
Model Code - UMA-5.01-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 55084
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 55084
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2171.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-5.01 (Continued)
Indoor Unit
Model Code - UMA-5.01-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 35000
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 35000
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2171.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-5.02
Outdoor Unit
Model Name AM100JXVANH/TL
Module Single
Mode HP
HP 10
MCA A 21.10
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 3/8''
Connections Type Welding
Gas Pipe
Diameter in 7/8''
Type R410A
Refrigerant
Factory Charging kg 5.50
DVM Pro 2.0
Product Specification
UMA-5.02 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 58
Sound Pressure
Sound
Cooling dB(A) 79
Power Level
Net Weight kg 197.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-5.02 (Continued)
Indoor Unit
Model Code - UMA-5.02-H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 68277
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 68277
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2969.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-5.02 (Continued)
Indoor Unit
Model Code - UMA-5.02-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 50600
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 50600
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 2969.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-5.03
Outdoor Unit
Model Name AM120JXVANH/TL
Module Single
Mode HP
HP 12
MCA A 25.00
Current
MFA A 32.00
Type Propeller
Output W 830
Type Welding
Liquid Pipe
Piping Diameter in 1/2''
Connections Type Welding
Gas Pipe
Diameter in 1 1/8''
Type R410A
Refrigerant
Factory Charging kg 6.50
DVM Pro 2.0
Product Specification
UMA-5.03 (Continued)
Outdoor Unit
Sound
Cooling dB(A) 62
Sound Pressure
Sound
Cooling dB(A) 81
Power Level
Net Weight kg 210.00
W mm 880
W mm 948
D mm 832
Min. °C -5.0
Cooling
Operating Max. °C 48.0
Temp. Range Min. °C -25.0
Heating
Max. °C 24.0
DVM Pro 2.0
Product Specification
UMA-5.03 (Continued)
Indoor Unit
Model Code - UMA-5.03.H
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 86985
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 86985
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3233.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0
DVM Pro 2.0
Product Specification
UMA-5.03 (Continued)
Indoor Unit
Model Code - UMA-5.03-C
Power Specification (Φ, #, V, Hz) -
Total Capacity (Nominal) Btu/h 48200
Cooling
Capacity Sensible Heat (Nominal) Btu/h 0
Heating Total Capacity (Nominal) Btu/h 48200
Cooling Rated kW 0.00
Power Consumption
Heating Rated kW 0.00
Installation - Floor standing
Airflow Rate High CFM 3233.00
Fan
External pressure Maximum Pa 448.00
Flow Rate Rated LPM -
Heat Exchanger Pressure Loss Rated kPa -
Internal Volume liter -
Entering and Leaving Water Pipe in -
Liquid Pipe in
Piping Diameter
Gas Pipe in
Drain Pipe in
Weight (Dry) kg 0
Width (W) mm 0
Product Dimension Height (H) mm 0
Depth (D) mm 0